 | | Re: IC serial hog?
|
|
yes, it is possible for an ic program to use the serial port. see randy's instructions at (URL) (29 years ago, 12-Feb-96, to lugnet.robotics.handyboard)
|
| |
| | Re: Sony IR decoding routine!
|
|
ic is very sensitive to linefeed termination in icb files. if you are runnnin on an ms-dos system, i believe it requires unix style (e.g., ctrl-j) termination, rather than ms-dos ctrl-m ctrl-j style. try removing the ctrl-m's from your copy of the (...) (29 years ago, 12-Feb-96, to lugnet.robotics.handyboard)
|
| |
| | IC serial hog?
|
|
Is there any way for my IC program to use the serial port? I am guessing the answer is no, as IC needs it for communicationg to the host computer. (Mac in my case.) So then the question becomes, is it possible to modify IC so that I can use the (...) (29 years ago, 12-Feb-96, to lugnet.robotics.handyboard)
|
| |
| | RE: Sony IR decoding routine!
|
|
I'm having trouble getting sony-ir.icb to load. Every time I try, I get the following error message: FATAL INTERNAL ERROR: ILLEGAL LINE IN .s19 FILE I've re-downloaded and installed both the sony-ir.icb and pcode_hb.s19 files but continure to get (...) (29 years ago, 11-Feb-96, to lugnet.robotics.handyboard)
|
| |
| | NEW! - Handyboard Hard-to-Get Parts Kit!
|
|
CW Technology is now offering a kit of only the "hard to get" parts for the Handyboard 1.2. Basically, the kit includes everything you can't get at DigiKey and Mouser. The price is very competitive if you consider the minimum orders, shipping, etc. (...) (29 years ago, 11-Feb-96, to lugnet.robotics.handyboard)
|
| |
| | Can't initialize CONFIG register
|
|
Hello, Everyone: Help! I'm trying to configure the HB. Here's what I get: C:\IC> dlm config0c.s19 -port COM2 -eeprom DLM: 6811 File Downloader... etc. Using COM2 Downloading to EEPROM Downloading config0c.s19, press ESC to abort Downloading eeprom (...) (29 years ago, 11-Feb-96, to lugnet.robotics.handyboard)
|
| |
| | Re: charger board problems
|
|
You could just get an adapter that is rated for a lower voltage. Try a nine volt adapter or a universal one that you can experiment with. -Fred -- This message was composed using Articulate Systems' PowerSecretary. Please forgive any sloppiness in (...) (29 years ago, 11-Feb-96, to lugnet.robotics.handyboard)
|
| |
| | Re: charger board problems
|
|
(...) Or just use different motors. ;-) (29 years ago, 11-Feb-96, to lugnet.robotics.handyboard)
|
| |
| | charger board problems
|
|
I've managed to stick a wire onto a point in my battery pack which yields 6V. (temporary solution, at least...) However, the charger board doesn't seem to like this new arrangement much. With the lower battery voltage, too much current is flowing (...) (29 years ago, 11-Feb-96, to lugnet.robotics.handyboard)
|
| |
| | battery voltages
|
|
I'm currently trying to get 6V out of my 9.6V battery pack. (I actually looked around for a 6V one, but couldn't find one that would work...) I've opened up the pack, and can access the cell where I can get 6V. However, I'm not sure how to get a (...) (29 years ago, 11-Feb-96, to lugnet.robotics.handyboard)
|
| |
| | Quad encoders
|
|
Thx to the advice of many of you I am using encoders from mice as shaft encoders. The code in the libraries does not seem to take into account encoders with TTL signal in quadrature. Therefore I do not get direction from the current software. Maybe (...) (29 years ago, 11-Feb-96, to lugnet.robotics.handyboard)
|
| |
| | IC Problems
|
|
(...) Brian> But then the question still remains, how can I define a list of Brian> consecutive memory locations in a .icb file and then access Brian> them from within a loop in a .c file? [ ... ] Brian> Anybody run into this before or have any (...) (29 years ago, 8-Feb-96, to lugnet.robotics.handyboard)
|
| |
| | IC Problems
|
|
OK, OK. RTFM, I know. I looked at the on-line manual, and now realize that IC arrays are different than normal C arrays, and so you can't do stuff like int m() { int *address; address=&a0; address++; } But then the question still remains, how can I (...) (29 years ago, 8-Feb-96, to lugnet.robotics.handyboard)
|
| |
| | IC Problems
|
|
OK all of you IC gurus. How come I can't do this: int m() { int *address; address=&a0; address++; } a0 is a variable defined in an .icb file. I also can't do something like address=address+2; or address[4]=7; Why not? This is all pretty standard C (...) (29 years ago, 8-Feb-96, to lugnet.robotics.handyboard)
|
| |
| | Re: 5mm range reflectance sensor
|
|
(...) Very nice ASCII graphics. I don't know this part but assuming that the + and L pins are the pins which control the transmitter, and asuming the reciever is a photo transistor that should act as a switch, I would say that you should connect the (...) (29 years ago, 8-Feb-96, to lugnet.robotics.handyboard)
|
| |
| | 5mm range reflectance sensor
|
|
Hello, I've got a 5mm range reflectance sensor which I am trying to get to work with the handyboard, without much success. Here is what I have: DigiKey part #: OR506-ND Manufacturer #: EE-SB5V The labels on the leads are as follows: .--- (+) .--, / (...) (29 years ago, 8-Feb-96, to lugnet.robotics.handyboard)
|
| |
| | announcing the HB Expansion Board version 2.0!!
|
|
Greetings all, The Handy Board Expansion Board version 2.0 design is complete! I'm pretty excited about the feature set, which includes a bunch of things not on the older (not released) expansion boards: * high-impedance analog inputs * PIC (...) (29 years ago, 7-Feb-96, to lugnet.robotics.handyboard)
|
| |
| | Caster Substitute
|
|
While there is some discussion on robot bases, let me add a bit about the "third wheel", usually a caster, used on differential drive systems. Casters have the advantage that they are plentiful, cheap, and come in lots of sizes and configurations. (...) (29 years ago, 7-Feb-96, to lugnet.robotics.handyboard)
|
| |
| | Using cheap RC chasis as 'bot
|
|
I used a Fischer Price RC car: well built with two gear settings and quite battery efficient. Once the RC receiver was ripped out, there was plenty of space for the Miniboard to be mounted internally. However, I chose to mount it on top in a (...) (29 years ago, 7-Feb-96, to lugnet.robotics.handyboard)
|
| |
| | Re: battery voltages
|
|
(...) I'd use 6V instead of the 9.6V main power supply - connect it where the main battery terminals are. It'd be really nice if the handy board had a way to use voltages other than 9.6V for the motor driver chips, ya know. :-) (29 years ago, 7-Feb-96, to lugnet.robotics.handyboard)
|
