 | | (canceled)
|
|
|
| |
 | | (canceled)
|
|
|
| |
 | | (canceled)
|
|
|
| |
 | | Re: is Mindstorm/RCX Y2K Compliant???
|
|
(...) microcontroller in the RCX does this, or not. Jasper (28 years ago, 22-Jan-99, to lugnet.robotics)
|
| |
 | | Re: Flexible axles!!!!
|
|
what exactly is znap? thanks! -- Chris Stanley cstanley@usit.net (...) (28 years ago, 22-Jan-99, to lugnet.robotics)
|
| |
 | | Re: RCX 2.0 -- ideas.
|
|
(...) The big cost in these things, wqould be that you need 5 of the 2*2*2/3 plates at the end of Technic leads, unless you homebrew those too. AFAIK, you can only get leads, at least as far as Service packs are concerned, for about $5-$6 (with 2 (...) (28 years ago, 22-Jan-99, to lugnet.robotics)
|
| |
 | | Re: expansion ports
|
|
(...) Reductio ad absurdam: You buy, say, 8880. You lose one of the, say, #12 axles. You replace with 2 #6 and an axle extender. You sell it on (bad move, IMHO, but hey, it could happen :) ). By your reasoning, you now have sold a product, not made (...) (28 years ago, 22-Jan-99, to lugnet.robotics)
|
| |
 | | Re: Smooth Plates
|
|
(...) Set 6567 Speed Splasher has two red 1*8 tiles. It is available under $2.50, generally. But don't tell your SO, or you won't be able to buy a few multiples of 8277 :) (just bought two myself, over the last few days... I now have a _really_ (...) (28 years ago, 22-Jan-99, to lugnet.robotics)
|
| |
 | | Re: Squishy Brick
|
|
(...) Is that the page where there is a 1*4 grey technic beam, pierced by a #3 or 4 axle, with a 16-tooth bevel (?) gearon one side, and a washer on the other? I think they put that picture in all Technic sets, to tell you that the axles have to be (...) (28 years ago, 23-Jan-99, to lugnet.robotics)
|
| |
 | | Re: homebrew Temp sensor
|
|
(...) Hmm.. why no elco? that is, if you make sure you alway plug your sensor on in the same way, you should get a constant +ve and -ve... Mindstorms does use the standar measuring trick of having DC current run thru the resistor, right? Jasper (28 years ago, 23-Jan-99, to lugnet.robotics)
|
| |
 | | Re: The Handyboard (was Re: RCX 2.0 -- ideas.)
|
|
(...) How about using a few large plates (of the type found as baseplates in small to medium sets), and a few basic bricks, possibly with the addition of glue to keep it all together? Jasper (28 years ago, 23-Jan-99, to lugnet.robotics)
|
| |
 | | Re: expansion ports
|
|
Jasper Janssen wrote in message <36a90add.169456990@...et.com>... (...) Your examples are irrelevant because they probably don't still have active patents on the pieces and may or may not have ever had patents on all of them. What I was talking (...) (28 years ago, 23-Jan-99, to lugnet.robotics)
|
| |
 | | NQC 1.1 b1
|
|
Due to feature creep, NQCC 1.0 never got out of beta. I've merged nqcc and the various utiltites (rcxfirm, rcxlog, etc) into a single program called nqc, and added some minor improvements to the compiler as well. The command line has changed quite a (...) (28 years ago, 23-Jan-99, to lugnet.robotics)
|
| |
 | | Re: homebrew Temp sensor
|
|
Jasper Janssen wrote in message <36a914e5.172025205@...et.com>... (...) Right, you could use an electrolytic if you wanted to make sure you always plugged your sensor the right way. Many people who are in this group do not know the subtleties of (...) (28 years ago, 23-Jan-99, to lugnet.robotics)
|
| |
 | | Re: The Handyboard (was Re: RCX 2.0 -- ideas.)
|
|
(...) But that would do nothing towards making it truly LEGO electric compatible; coming up with a suitable compartment for the motherboard that leaves room for the expansion board, even if it's not actually connected yet; leaving the display and (...) (28 years ago, 23-Jan-99, to lugnet.robotics)
|
| |
 | | RCX message's
|
|
Hi everybody, I'm new to this newsgroup, and I've found much interesting information on this group. I'm writing a hypercard XFCN to control the Cybermaster and it is working right now, but I have problems with the following messaging commands : 90 (...) (28 years ago, 23-Jan-99, to lugnet.robotics)
|
| |
 | | Re: Flexible axles!!!!
|
|
It is Lego's answer to K'nex. The sets are searchable by there number at Lugnet. try 3552 I think its on the Lego catalog page as well. LINC Chris Stanley wrote in message <36A8FB60.F345807A@usit.net>... (...) (28 years ago, 23-Jan-99, to lugnet.robotics)
|
| |
 | | DATALOG and C
|
|
Hi all, Could someone write a C program that just hangs out and waits for the RCX to send a datalog to it? RCXLOG is great but not quite what I need. RCXLOG.exe Tells the RCX to upload a datalog, prints it out, then quits. I'd like something that (...) (28 years ago, 23-Jan-99, to lugnet.robotics)
|
| |
 | | Re: mouse
|
|
(...) Personally, I've never been able to figure out just jow a mouse does that, either :) Jasper (28 years ago, 23-Jan-99, to lugnet.robotics)
|
| |
 | | Re: DATALOG and C
|
|
Brandon wrote in message <36A93B81.4F96@sprynet.com>... (...) I doesn't work that way. The RCX sends up to 50 data points at a time when it sees the UploadDatalog command. The RCX won't do anything thing like that from a program. The UploadDatalog (...) (28 years ago, 23-Jan-99, to lugnet.robotics)
|