 | | Re: List software?
|
|
Steve Baker writes: > Chris 'Xenon' Hanson wrote: > > > I can't enumerate the number of time's (like just a moment ago) > > that I replied directly to the sender, not to the list, forgetting > > to change the To line. > > What ends up happening is (...) (24 years ago, 3-Apr-01, to lugnet.robotics)
|
| |
| | Re: Lubricating technic turntables
|
|
(...) DISCLAIMER: I've never tried this... I'd definitely avoid any kind of liquid lubricant. I'd guess that a dry graphite lubricant would work - the kind of thing that's recommended for lubricating door locks that comes with a nice thin nozzle to (...) (24 years ago, 3-Apr-01, to lugnet.robotics)
|
| |
| | Lubricating technic turntables
|
|
Greetings, Any suggestions to safely yet effectively lubricate technic turntables? I have four which are somewhat stiff and require a fair amount of torque to rotate. Thanks in advance! Cheers, Carl Jagt (24 years ago, 3-Apr-01, to lugnet.robotics)
|
| |
| | Re: List software?
|
|
(...) Ditto. I find this *INCREDIBLY* annoying - because this is the only one of over a dozen mailing lists that I'm subscribed to that works this way. What ends up happening is that people *don't* politely edit the 'To:' lines - instead they hit (...) (24 years ago, 2-Apr-01, to lugnet.robotics)
|
| |
| | Re: Racing Line Follower
|
|
(...) I've built a few line followers to see how fast I can do the test track - but I've concluded that you have a quality/speed tradeoff. I've built robots that *approximately* follow the track at these kinds of speeds - but without some kind of (...) (24 years ago, 2-Apr-01, to lugnet.robotics)
|
| |
| | Re: Racing Line Follower
|
|
In Creative Projects I make recommendations on line followers. One of them is to add a touch sensor that you can use as a trigger to grab the light levels of the line and the surface and store them in memory. Then you can use the average of those (...) (24 years ago, 2-Apr-01, to lugnet.robotics)
|
| |
| | Delayed BrickBots contest results
|
|
Hi Folks, Two BrickBots.Com contests ended last week, and here is a rundown of the results. First, the Top Spinning Challenge - Get as many tops spinning simultaneously for as long as possible. (URL) Tip Top Top Tipper Score: 27 points! (URL) (...) (24 years ago, 2-Apr-01, to lugnet.robotics)
|
| |
| | Re: List software?
|
|
(...) In my experience, one wants to reply to the list more often than just to the sender. Perhaps I'm wrong. In any case, anyone wishing to just reply to the sender would remove the list address from their outgoing message, and fill in the sender's (...) (24 years ago, 2-Apr-01, to lugnet.robotics)
|
| |
| | Re: List software?
|
|
(...) No no no no no no no!!!! I ABSOLUTELY hate mailing lists that do that; it makes it near impossible to reply just to the sender. --Ken (24 years ago, 2-Apr-01, to lugnet.robotics)
|
| |
| | Re: Racing Line Follower
|
|
(...) HeHeHe !!! :-) (24 years ago, 2-Apr-01, to lugnet.robotics)
|
| |
| | Re: Racing Line Follower
|
|
I think I would take your stop watch back to the jeweler. -- Bob Fay rfay@we.mediaone.net (URL) Fasting" <lego-robotics@crynwr.com> wrote in message news:3.0.6.32.200104...line.no... (...) (24 years ago, 2-Apr-01, to lugnet.robotics)
|
| |
| | List software?
|
|
What software runs this mailing list? I ask because I'd like to find out what it would take to get it to put the ML address into messages as the Reply-To address. I run a couple of lists myself (using 7-line SED scripts) and it seems like this (...) (24 years ago, 2-Apr-01, to lugnet.robotics)
|
| |
| | Re: Shutting off illumination LED on Light Sensor for LIDAR
|
|
(...) Yes, this is the result I discovered this weekend. My conclusion is that setting the sensor to raw mode does not fully remove the light produced by the LED, and detrimentally impacts the sensor performance. I think my next approach is to try (...) (24 years ago, 2-Apr-01, to lugnet.robotics)
|
| |
| | Racing Line Follower
|
|
Hello I've built a line follower which is quite fast (approx 4 secs per lap on the testpad). It consists of two motors, each powering a 2/3 geared large wheel. Two light sensors are attached to the front pivot wheel. The distance between the sensors (...) (24 years ago, 2-Apr-01, to lugnet.robotics)
|
| |
| | Re: David Schilling
|
|
Oh I see. thanx....good luck! (...) (24 years ago, 2-Apr-01, to lugnet.robotics, lugnet.org.us.smart)
|
| |
| | Re: David Schilling
|
|
(...) I built the Killough platform for the March SMART meeting mini-challenge. (SMART is the Seattle Mindstorms and Robotic Techies group.) The basic idea was to build a robot to wander around a table, without falling off, and stop beside a heavy (...) (24 years ago, 2-Apr-01, to lugnet.robotics, lugnet.org.us.smart)
|
| |
| | Re: David Schilling
|
|
I built a Killough platform based on Leo Dorst's site and Doug Carlson's site. I have a quicktime movie and links to Leo's and Doug's sites available at: (URL) this helps! (...) (24 years ago, 2-Apr-01, to lugnet.robotics)
|
| |
| | Re: David Schilling
|
|
Looks like a form of the Killough platform on Leo Dorst's site. The rods appear to provide a 'shell' to keep the blue base from getting stuck in the v area. There are movies of the motion on Doug Carlson's site. I do not have any links handy, but (...) (24 years ago, 1-Apr-01, to lugnet.robotics)
|
| |
| | RE: Curved Feet
|
|
Scott, I see this set frequently on eBay. There are six there now. Just search for "8880". I got two that way. It's a great set, though I feel that the suspension and joints to transmit driving power to the wheels are rather inflexible. Most of the (...) (24 years ago, 2-Apr-01, to lugnet.robotics)
|
| |
| | Re: Solar Cell Output (Shell logo)
|
|
Here's another link. (URL) Regards Micah J. Mabelitini - LUGNET #918 The University of Kentucky SECC Middlesboro Academic Skills Resource Center accutron@kih.net - (URL) (24 years ago, 2-Apr-01, to lugnet.robotics)
|
