To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / *5701 (-20)
  Re: Cybermaster Sensors
 
(...) What do you mean parallel? I once connected 2 touch sensors to the same port and they worked like a logic OR if is that you are asking. (28 years ago, 30-Nov-98, to lugnet.robotics)
 
  Re: CyberMaster memory limit?
 
(...) Automatic Gain Control voltage. I misspelled it in the source (sorry!) -> Change ACG() to AGC(). As stated in the RCX.NQH, refer to the LEGO SDK for information about these functions. The only reference to this function in in the page 45 of (...) (28 years ago, 30-Nov-98, to lugnet.robotics)
 
  Logic level conversion
 
I have a device that uses 0 - 3V logic levels for the data output. What can I do to convert the output to match the 68HC11's 0 - 5V logic level? Thanks for the help, Dave (28 years ago, 30-Nov-98, to lugnet.robotics.handyboard)
 
  Re: Good 9V motor source -Reply
 
These motors are exellent quality and very powerful the gears are metal and the motors does not exed 300 mA @12V stalled. I currently use the same motors on my robot and had no problems at all. I drive them using the motor drivers on the Handy Board (...) (28 years ago, 30-Nov-98, to lugnet.robotics.handyboard)
 
  Re: Print to IC's console window
 
(...) there is no builtin way of doing this. to get msgs back over the serial line, see the FAQ question at: (URL) Is it true that the handy board can only work when the LCD is plugged onto (...) you need a replacement pcode file to let the HB work (...) (28 years ago, 30-Nov-98, to lugnet.robotics.handyboard)
 
  Re: CyberMaster memory limit?
 
(...) Excuse me for being stupid, but what is AGC()? I couldn't find any reference to it in the rcx.nqh file. Fredrik (28 years ago, 30-Nov-98, to lugnet.robotics)
 
  Good 9V motor source -Reply
 
jameco (www.jameco.com) has several new gear head motors in the 3-12v range with various gear ratios. I ordered two for my latest project and they seem to be solid and up to the task. jameco's latest catalog also has some robotic stuff including (...) (28 years ago, 30-Nov-98, to lugnet.robotics.handyboard)
 
  Re: Extra output for clocking
 
Hugo Robertson: One of the nice things about the 68HC11 chip is its well rounded timming system. Grab your Handy board Technical reference manual and have a look at page 48. PA0-3 are "Input Capture" pins. When the logic level changes (according to (...) (28 years ago, 30-Nov-98, to lugnet.robotics.handyboard)
 
  Re: Cybermaster Sensors
 
(...) Thinking ahead, and also if I recall because the set had the idler gear in it, I bought several of the rubber-skirted hovercraft some years ago. It isn't flexible but it's soft and it looks cool. And implausibly enough it's real LEGO. Haven't (...) (28 years ago, 30-Nov-98, to lugnet.robotics)
 
  Print to IC's console window
 
Hi, Does anyone know how to print messages to the IC's console window while running IC.exe. Is it true that the handy board can only work when the LCD is plugged onto the handy board ? It is because when ever it unplugged the LCD from the handy (...) (28 years ago, 30-Nov-98, to lugnet.robotics.handyboard)
 
  Cybermaster Sensors
 
In message <4.1.19981128213514....lepac.pt>, Laurentino Martins <lau@mail.telepac.pt> writes (...) In the book "Mobile Robots" by A.M.Flynn it suggests three bump sensors which are activated by circular plastic skirt made out of acrylic plastic. It (...) (28 years ago, 30-Nov-98, to lugnet.robotics)
 
  Re: Pneumatic Air Tanks
 
Shane Weston wrote in message (...) You will have much better luck with a micro motor on that switch. I can't even imagine what would happen when the switch reached the end of its throw and a geared motor is still going. A micro motor stalls, but it (...) (28 years ago, 30-Nov-98, to lugnet.robotics)
 
  Re: Worm Drive Question
 
toys r us has 8735 for around $38. tim (...) (28 years ago, 30-Nov-98, to lugnet.robotics)
 
  Left and right axles rotating at same speed
 
In regard to propelling a robot with both the left and right axles turning at the same speed (or, moving in a straight line): Perhaps this was already suggested, but if not, here is another solution that uses only one differential and two motors, (...) (28 years ago, 30-Nov-98, to lugnet.robotics)
 
  uncondition jump to label
 
Hi all, Can we use goto command in IC for unconditional jump to label. If yes, how. If no, any alternative any body using for this. Help would be much appreciated. regards Javaid Iqbal (28 years ago, 30-Nov-98, to lugnet.robotics.handyboard)
 
  Extra output for clocking
 
I have a stepper motor controlled by a Motorola MC3479 driver, which basically allows me to input a clock and the direction from the handyboard and the driver does the sequencing. So I'm using 2 pins from the HB's motor output for controlling the (...) (28 years ago, 30-Nov-98, to lugnet.robotics.handyboard)
 
  Re: Good 9V motor source
 
(...) The Bulldozer kit has a decent gearbox in it, however there are some problems with it. The motors are 3v, so you really need to use an alternate power supply. Also, the tracks are not very good at all and will not last under any real use. the (...) (28 years ago, 30-Nov-98, to lugnet.robotics.handyboard)
 
  Re: Good 9V motor source
 
(...) Try Lego Technic kits. Start with a basic kit like the Giant Model Set (#8277) for $44, and add a couple 9V mini gear motors (#5225) for $17.50 each and a gear assortment for $4.50. Call Lego Shop-At-Home for a catalog (1-800-453-4652). If (...) (28 years ago, 29-Nov-98, to lugnet.robotics.handyboard)
 
  Re: Choosing a shaft encoder?
 
(...) I would have to agree. We evaluated incremental encoders from US Digital. We purchased the "low cost" encoders and paid just over $54 US. -d # rsh -l God universe.all find / -name '*windows*' -exec rm -rf {} \; (28 years ago, 29-Nov-98, to lugnet.robotics.handyboard)
 
  Good 9V motor source
 
Hi all....I'm looking for a good source of 9V gear motors that i could use with the handyboard for a mobile robot. Currently, i am just using the little 9v motors that came with the board, which i have plugged into the cheap gearbox from a toy tank, (...) (28 years ago, 29-Nov-98, to lugnet.robotics.handyboard)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR