To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / *5641 (+20)
  Choosing a shaft encoder?
 
As a neophyte robot builder and HandBoard user, may I ask for help in choosing the best shaft encoder? What vendor/supplier should I use? The current project is a very simple robot with a goal of accurate navigation. Thanks! (28 years ago, 28-Nov-98, to lugnet.robotics.handyboard)
 
  When people answer a question, I would like to broaden my knowledge as well.
 
Please either carbon copy your solutions to me, or the HB mailing list. I see a lot of good questions, but only a very few peoples responses. Thank you, (28 years ago, 28-Nov-98, to lugnet.robotics.handyboard)
 
  CyberMaster memory limit?
 
I've been playing around with programming the CyberMaster unit with NQC. I've noted that when the size of the program gets too large, the execution of the program fails in some way. The way it fails is sometimes somewhat inconsistent. I don't know (...) (28 years ago, 28-Nov-98, to lugnet.robotics)
 
  Re: How to use the addition analog port ?
 
You can time share both your digital and your analog so long as your signal update speeds are not critical. Use a 4 to 8 demultiplexing chip for 4 of your digital I/O and an 8 to 4 multiplexer for the other 4. This effectively provides 8 digital (...) (28 years ago, 28-Nov-98, to lugnet.robotics.handyboard)
 
  Re: Worm Drive Question
 
(...) This is an excellent solution for travel up to 7 inches or so, with a couple of minor drawbacks. 1) This part doesn't seem to be in production any more. I got a few copies, courtesy of Bill Katz, but had to trade away one joint of my little (...) (28 years ago, 28-Nov-98, to lugnet.robotics)
 
  Re: Worm Drive Question
 
(...) Nope, not me. I never cut on purpose, and anything that breaks gets tossed. (28 years ago, 28-Nov-98, to lugnet.robotics)
 
  Re: Worm Drive Question
 
(...) tend to slide on the axle over time? (28 years ago, 28-Nov-98, to lugnet.robotics)
 
  Re: Choosing a shaft encoder?
 
(...) I've had good results using the Hall-effect magnetic sensors that Patrick Hui sent with my HandyBoard. I glued magnets into three of the six holes in a Lego pulley wheel and glued the sensor into a small Lego brick. I don't know the part (...) (28 years ago, 28-Nov-98, to lugnet.robotics.handyboard)
 
  Re: CyberMaster memory limit?
 
Your program generates a .RCX file of 440 bytes. I've created one with 452 that works OK, but had to stop around that number because after more 2 or 3 lines of code the last task simply disappeared (my program had 1 main plus 3 tasks). I guess the (...) (28 years ago, 28-Nov-98, to lugnet.robotics)
 
  Re: Worm Drive Question
 
Try a little white glue. The glue helps prevent slippage and can be easily removed with warm water. Another option is a low-temperature "hot" glue gun. Many of the "hot" glue gun glues can be removed with vinegar. Use these at your own risk. matt (...) (28 years ago, 28-Nov-98, to lugnet.robotics)
 
  Re: Worm Drive Question
 
(...) When did TLG start making white glue?? Cool! <grins, ducks and runs...> (28 years ago, 28-Nov-98, to lugnet.robotics)
 
  Re: Choosing a shaft encoder?
 
(...) hy, I used HewlettPackard shaft encoders HEDL5540 (500 steps per revoltion) with HCTL2020 quadrature shaft counters/decoders. With them you get 500*4=2000 steps per revolution, which is quite a lot. For me They seem to be a good (but not (...) (28 years ago, 28-Nov-98, to lugnet.robotics.handyboard)
 
  Re: CyberMaster memory limit?
 
In message <4.1.19981128170141....lepac.pt>, Laurentino Martins <lau@mail.telepac.pt> writes (...) This use of software to determine direction is what I was alluding to in an earlier post when the others were trying to get their mobile to travel in (...) (28 years ago, 28-Nov-98, to lugnet.robotics)
 
  Re: CyberMaster memory limit?
 
In message <4.1.19981128170141....lepac.pt>, Laurentino Martins <lau@mail.telepac.pt> writes (...) Does this work on Windows NT or Win 95? Dennis (28 years ago, 28-Nov-98, to lugnet.robotics)
 
  Re: legOS corruption
 
(...) Yeah, yeah. I'm sure we've all got "I debugged that with no more than an LED and 3 inches of wire" stories, but only a fool would spurn a logic analyser when it was available. Cheers, Ben. (28 years ago, 28-Nov-98, to lugnet.robotics)
 
  Optrex lcd displays
 
I am trying to interface an Optrex DMC display to a miniboard. What pins besides the data lines need to be connected and to what? Anyone used these displays yet, I have two a one line x 16 characters and a two line x 16 characters. The pin out (...) (28 years ago, 28-Nov-98, to lugnet.robotics.handyboard)
 
  Re: CyberMaster memory limit?
 
(...) There's nothing unknown about the Tachos. If you need help using them, gimme a call. :-) (...) Yeah, I've also started with that bot. It's very well designed! And I've never exchanged any batteries! :-) (...) The best vehicle would be one with (...) (28 years ago, 28-Nov-98, to lugnet.robotics)
 
  Re: CyberMaster memory limit?
 
(...) You bet it does! My system is a Win98, which is great since I will need to use the SPIRIT.OCX that only works in Windows machines. Laurentino Martins PS: Why you always send every mail twice? (28 years ago, 28-Nov-98, to lugnet.robotics)
 
  Re: Choosing a shaft encoder?
 
i use US Digital encoders, www.usdigital.com. they are a bit costly, but very accurate, and have quite a few numbers of resolutions. good luck justin (28 years ago, 28-Nov-98, to lugnet.robotics.handyboard)
 
  Re: Optrex lcd displays
 
I must apologize for my last request, upon further investigation I found an excellent resource that answers the questions i posed earlier. For anyone who might be interested, the source can be found at : LCD MODULE TECHNICAL REFERENCE (FAQ) Version (...) (28 years ago, 28-Nov-98, to lugnet.robotics.handyboard)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR