 | | Re: IR Tower not working when downloading firmware
|
|
(...) Which physical pins are 2 and 3? I assume they would be the Tx and Rx pins, but I don't know where they are. Pretty cool - data going through a paperclip. (24 years ago, 11-Jan-03, to lugnet.robotics)
|
| |
 | | Re: IR Tower not working when downloading firmware
|
|
Andrew J. Huang wrote: > Wendy's problem is (...) The way to figure out which serial port on the back of the PC corresponds to which COM port is to use the world's cheapest piece of test equipment...the lowly paperclip. Bend your paperclip into a U (...) (24 years ago, 11-Jan-03, to lugnet.robotics)
|
| |
 | | Re: Not really LEGO...
|
|
"Michael Obenland" <obenland@t-online.de> wrote in message news:H8I2sr.9Lz@lugnet.com... (...) Iain (24 years ago, 11-Jan-03, to lugnet.robotics)
|
| |
 | | Re: Can't run software
|
|
(...) Thanks again Matthais, I have downloaded and installed this driver. But unfortunately there is no change. Bill Lane (24 years ago, 11-Jan-03, to lugnet.robotics.spybotics)
|
| |
 | | Re: IR Tower not working when downloading firmware
|
|
No! Unless you need two RCXs - and that's a different question ;) Donwloading the firmware seems to be the most "stressful" exercise of the tower/RCX link. The download functions offered include a high speed mode and normal mode. The tower and RCX (...) (24 years ago, 10-Jan-03, to lugnet.robotics)
|
| |
 | | Re: Spybotics Internals
|
|
(...) Sure...that would be a good reference for the page as well. I'll try and do that next week. Steven (24 years ago, 10-Jan-03, to lugnet.robotics.spybotics)
|
| |
 | | RE: IR Tower not working when downloading firmware
|
|
Andy, It is not COM port problem. I have used the same PC and the same configuration to successfully download to RCX the night before I took all the batteries out of the RCX. After 24 hours without battery, the RCX lost its firmware. It fails to (...) (24 years ago, 10-Jan-03, to lugnet.robotics)
|
| |
 | | RE: IR Tower not working when downloading firmware
|
|
Wendy, Dick, I'm fighting the same issue on a RIS 1.5. I haven't resolved the problem yet but let me share what I've found. Character echo means only that you've connected to the IR tower. Using hyperterminal, I get perfect echoes, but I get them (...) (24 years ago, 10-Jan-03, to lugnet.robotics)
|
| |
 | | RE: IR Tower not working when downloading firmware
|
|
Thanks for the response. I just got back from a trip and see this message. I did perform the test you mentioned in the email. I used the hyper terminal program to determine that the problem is lack of echoed characters. What is your advice on fixing (...) (24 years ago, 10-Jan-03, to lugnet.robotics)
|
| |
 | | Re: Big synchro drives: vacuum cleaner, lawn mower
|
|
Thanks everyone for the comments. Iain: I know the offset solutions. Two wheeled seemed to be a lot more stable back then. Rob: Good stuff on your page. Do you thing BrickOS will read the rotation sensor faster? That might solve everything. BTW, I (...) (24 years ago, 10-Jan-03, to lugnet.robotics)
|
| |
 | | Re: Can't run software
|
|
(...) the (...) led (...) you (...) motherboard (...) here we go: Windows 95, 98 and Me will automatically recognize and load a driver for the Tseng Labs chip sets on all of the Ultimate VGA boards. All of the resolutions and color depths that the (...) (24 years ago, 10-Jan-03, to lugnet.robotics.spybotics)
|
| |
 | | RE: H-bridge for PDA?
|
|
(URL) (...) (24 years ago, 10-Jan-03, to lugnet.robotics)
|
| |
 | | Not really LEGO...
|
|
...but stunning nevertheless. Take a look at: (URL) (24 years ago, 10-Jan-03, to lugnet.robotics)
|
| |
 | | Re: Big synchro drives: vacuum cleaner, lawn mower
|
|
(...) A disclaimer should be used when the LEGO trademark appears on a Web page. An appropriate disclaimer would be "LEGO® is a trademark of the LEGO Group of companies which does not sponsor, authorize or endorse this site". However, a disclaimer (...) (24 years ago, 10-Jan-03, to lugnet.robotics)
|
| |
 | | Re: Big synchro drives: vacuum cleaner, lawn mower
|
|
(...) IIRC, LEGO's Fair Play page has an example: (URL) (24 years ago, 10-Jan-03, to lugnet.robotics)
|
| |
 | | Re: Packaging!
|
|
(...) Sorry I was off the point I haven't been able to find the original context of this question. I hope there is another way to access them because I don't have enough COM ports to connect to the Spybot and the internet at the same time. If I try (...) (24 years ago, 10-Jan-03, to lugnet.robotics.spybotics, lugnet.lego)
|
| |
 | | Re: Can't run software
|
|
(...) The Display Adapter is a Tseng Labs ET4000/W32 PCI. It didn't come with the PC. I had trouble trying to run something a while back. Some research led me to this driver and it solved the problem. I must say I find the whole Display Adapter (...) (24 years ago, 10-Jan-03, to lugnet.robotics.spybotics)
|
| |
 | | Re: Can't run software
|
|
(...) Thanks for the thought Andy, I definitely have 320 MB of RAM. Yes it is a bit overboard. But when I had a hard drive replaced last year RAM was very cheap so I bought up. Yes, I understand I will have other bottlenecks that will diminish the (...) (24 years ago, 10-Jan-03, to lugnet.robotics.spybotics)
|
| |
 | | Re: H-bridge for PDA?
|
|
Now The idea is - Make a kit - sell it, the income shall go to a foundation for creative people around this email list.. And I guess all the schools that are outside there. Was money the problem How much time was it about to take? Maybe of topic: (...) (24 years ago, 10-Jan-03, to lugnet.robotics)
|
| |
 | | Re: Big synchro drives: vacuum cleaner, lawn mower
|
|
(...) Wow! That is so cool! When I first got my RIS I thought of making a platform that could drag our Vacuum along with it but never got around of doing one. Your all LEGTO solution is great! To bad you had to make such a complicated platform for (...) (24 years ago, 10-Jan-03, to lugnet.robotics)
|