To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / *26504 (-20)
  RE: Fiber Optics System controlling multiple motors
 
You can't actually do this the way you describe. You can't pulse the motor outputs as required to drive the FOS with the standard firmware. The FOS has only one LED, and the VLL signal is a bit more complicated than on/off. You can use the scout VLL (...) (26 years ago, 2-Feb-01, to lugnet.technic, lugnet.robotics.scout, lugnet.robotics.microscout)
 
  RE: Pneumatic tubing...
 
I measured some today, and I'd bet a micro scout that it's 4mm OD x 2mm ID. I suspect the material is actually polyurethane, although silicone would work just as well. It's easy to find the 4mm OD, but the 2mm ID is tough. I couldn't find anything (...) (26 years ago, 2-Feb-01, to lugnet.robotics)
 
  Sale price for Fiber Optics System at LSAH
 
You can get Fiber Optics at reduced price. LSAH Weekly Specials through Feb 6, 2001 has #9732 "Extreme Creatures" for sale US$25 (reg $50). See (URL) It has the FOS (Fiber Optic System) with 8 fiber optic cables and the 8-LED rotary part. For info (...) (26 years ago, 2-Feb-01, to lugnet.technic, lugnet.robotics.scout, lugnet.robotics.microscout, lugnet.robotics.vll)
 
  Fiber Optics System controlling multiple motors
 
You can build a Technic mechanical and optical system to control Mindstorms Scouts and Micro Scouts. The lights and optic cables from the FOS (Fiber Optic System) rotary LED assembly can provide the light sources and channels to the light sensors on (...) (26 years ago, 2-Feb-01, to lugnet.technic, lugnet.robotics.scout, lugnet.robotics.microscout)
 
  Remote Control of 3 motors with Scout & Micro Scout
 
You can remotely control each of 3 motors in both directions with a Scout and a Micro Scout. You need these parts: 1) Mindstorms Remote Control, 2) Mindstorms Scout, 3) Mindstorms Micro Scout, 4) 2 motors, 5) Lego Fiber Optic Cable (optional). You (...) (26 years ago, 2-Feb-01, to lugnet.technic, lugnet.robotics.scout, lugnet.robotics.microscout, lugnet.robotics.vll)
 
  Re: legOS lcd management and thoughts on velocities
 
Hello jochen, (...) Thank you for your precision about your velocity handler For now, unfortunaly my the hard disk does not boot any more, and, fortunatly, my wife gave birth to a girl on wednesday! So I'll test all those nice handlers in a few (...) (26 years ago, 2-Feb-01, to lugnet.robotics.rcx.legos)
 
  Re: Visual NQC 2001
 
Tim Webber pointed out to me that I must set the path to nqc.exe in the preferences. All is well now, thanks to Tim. -- Bob Fay California, USA rfay@we.mediaone.net (URL) (26 years ago, 2-Feb-01, to lugnet.robotics.rcx.nqc)
 
  Re: TLG support
 
Hej Marco! (...) At least in Germany it works this way, too. No hassles - free replacement - great service. And until now they've always responded to my emails within 3 to 5 days... Happy building, Sven (26 years ago, 2-Feb-01, to lugnet.robotics)
 
  Re: Pneumatic tubing...
 
(...) I use tubing that is typically used for the fuel lines in R/C airplanes. The tubing I bought is a little more "rubbery" than the lego tubing, but it still fits snuggly and works fine. I don't recall the ID, OD, etc. I just brought the lego (...) (26 years ago, 2-Feb-01, to lugnet.robotics)
 
  Re: Anyone using Mac beige G3
 
(...) The serial ports weren't changed in a major way (still RS-422, etc), but there could have been subtle changes to the driver/receiver that would cause problems when hooked to marginal RS-232 devices (such as the IR tower). Fred Martin reported (...) (26 years ago, 2-Feb-01, to lugnet.robotics.rcx.nqc)
 
  Re: Pneumatic tubing...
 
(...) Has anyone tried the tubing from Pitsco/Dacta? See: (URL) It has a 1/8" ID and a 100 foot roll is $9.00. Is it like the tubing in Pneumatic sets or is it a hard plastic tubing instead of rubber? Thomas (26 years ago, 2-Feb-01, to lugnet.robotics)
 
  Re: Pneumatic tubing...
 
(...) I believe that TLC has used the same tubing in a few non-pneumatic sets. I have one older pneumatic set here so I took a piece of tubing off of it and compared to some pieces that came off of the 6180 Hydro Search Sub. They appear to be quite (...) (26 years ago, 2-Feb-01, to lugnet.robotics)
 
  Re: Short Circute Problem -- EMERGENCY
 
Hi guys , i tried all the tests mentioned in the HB assembly to find out which part of the HB blown. No luck. i am giving the results here: 1) Tested the interface and charger board - looks good. (Both power supply and the MAX232 circuit) 2) Tested (...) (26 years ago, 2-Feb-01, to lugnet.robotics.handyboard)
 
  Re: Pneumatic tubing...
 
(...) the (...) Heck, ya got me ;-) Could be rubber, extremely soft polyurethane, or any number of compounds. You'd probably have to ask someone at TLG to identify it. I just bought a few packs of tubing from S@H to make sure I had enough. I get it (...) (26 years ago, 1-Feb-01, to lugnet.robotics)
 
  Re: Pneumatic tubing...
 
Dear Tom (...) it should have been in my original post) is the *material* and *x-sectional dimensions* for the LEGO pneumatic tubing. I have several sources for different kinds of tubing, but I want to get something as near identical to the LEGO (...) (26 years ago, 1-Feb-01, to lugnet.robotics)
 
  Re: Visual NQC 2001
 
<Runtime error 380 fix If you get Runtime error 380 during compile start you need to change the subdirectory where NQC.exe is stored. Use a directory without a space in the name. Example C:\NQC\nqc.exe This will work.> That did not work. I am still (...) (26 years ago, 1-Feb-01, to lugnet.robotics.rcx.nqc)
 
  Re: Anyone using Mac beige G3
 
(...) One thing to keep in mind about Mac serial ports is that they are not RS-232, rather they are RS-422. IIRC, RS-232 is a singled-ended voltage standard (ref to ground only), where RS-422 is a differential standard. The 'common' method of using (...) (26 years ago, 1-Feb-01, to lugnet.robotics.rcx.nqc)
 
  Re: Pneumatic tubing...
 
(...) I suppose you could check medical supply shops... You could also try www.newark.com, and request a catalog. If you are using Netscape Communicator, just type "pneumatic tubing" (without the quotes) into the URL field, and start with those (...) (26 years ago, 1-Feb-01, to lugnet.robotics)
 
  RE: 68HC11 (Evaluation Board)
 
I was wondering if anyone was aware of any pre-existing library calls that would allow an individual using an Evaluation Board (EVB-68HC11)+ Buffallo Monitor(ImageCraft C v5.0) to access the system clock. I've noticed that with using Interactive C (...) (26 years ago, 1-Feb-01, to lugnet.robotics.handyboard)
 
  Re: Pneumatic tubing...
 
Dear Tom (...) Thanks for your reply. You'll notice that I mentioned in my original question that the tubing available in the RC shops (which I referred to as poly tubing rather than neoprene -- my bad) is a bit stiff. I had a vague memory of (...) (26 years ago, 1-Feb-01, to lugnet.robotics)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR