 | | Re: Very strange problems
|
|
(...) Yes. We ran into similar problems when writing neural network code. Persist- you can write really cool stuff on legOS- we did. Also, emulegos (which is still around somewhere, though I'm not sure if anyone has ported it to 0.2.x) would (...) (26 years ago, 21-May-00, to lugnet.robotics.rcx.legos)
|
| |
 | | Re: Very strange problems
|
|
(...) That is really bad news. Since we are writing a genetic programming system with six RCXs involved that communicate with each other, the programs tend to get pretty long. Often things fail. Right now I have the problem that if I save a program (...) (26 years ago, 21-May-00, to lugnet.robotics.rcx.legos)
|
| |
 | | Re: Very strange problems
|
|
(...) As far as I can tell, legOS has some really strange bugs. I've learned to take it for granted that some programs (without warning) will just crash and lock up the machine. This is unfortunate, but I've never found a pattern to them so there is (...) (26 years ago, 21-May-00, to lugnet.robotics.rcx.legos)
|
| |
 | | Re: lnp communication question
|
|
(...) lnp does a checksum and throws away bad data. I think it is a 1 byte checksum so 1 out of 256 errors gets through anyway. There is no retry so timeout and retry has to be handled by some higher level code. (26 years ago, 21-May-00, to lugnet.robotics.rcx.legos)
|
| |
 | | Very strange problems
|
|
Hi! I am experiencing some very strange problems when programming my RCX. Sometimes (too often) the RCX just locks up when I run my program and I have to remove the batteries and reload the firmware. I have now found that very small changes in my (...) (26 years ago, 21-May-00, to lugnet.robotics.rcx.legos)
|
| |
 | | RE: Help with Terminal Emulator
|
|
(...) I have run into this too, Jerry. A few especially bothersome noise sources include video cameras, security systems, and remote controls. You might consider covering the RCX and tower with a box or towel... I'm glad the terminal emulator works (...) (26 years ago, 21-May-00, to lugnet.robotics.rcx.pbforth)
|
| |
 | | handyboard in Canada? (Montreal?)
|
|
I'd like to know, is anyone here from Montreal or the rest of Canada? Is there any distributor for handyboard parts or kits around here? All the ones I find are in the states (or hong kong...) -- You do not wish to know anything, you wish only to (...) (26 years ago, 21-May-00, to lugnet.robotics.handyboard)
|
| |
 | | Re: Help with Terminal Emulator
|
|
I think my problem is bounce back noise. I doubled checked the port settings, started with a fresh set of batteries, made sure I had a clear buffer, but what made the difference is where I am doing my programming. I'm working off of a laptop, and (...) (26 years ago, 20-May-00, to lugnet.robotics.rcx.pbforth)
|
| |
 | | Autonomous(ish) Robot Project
|
|
Hi, As a group project at Loughborough University we have been developing an autonomous explorer robot using Lego Mindstorms. The results of this years work are now complete and can be viewed at the following URL. From this link click on the (...) (26 years ago, 20-May-00, to lugnet.robotics)
|
| |
 | | Re: Sharp analog distance sensor
|
|
Follow this link for data about the GP2D12. At the bottom, there is another link for Handy Board interfacing information. You have to cut a trace because the analog inputs on the Handy Board are connected to pullup resistors. The GP2D12 won't work (...) (26 years ago, 20-May-00, to lugnet.robotics.handyboard)
|
| |
 | | arbitrary motor code
|
|
Did anyone ever write the wrapper to allow motor_dir(motor_label x, MotorDirection dir) or some such? There was a variant of it way, way back (0.1.5?) but I don't see anything like it in the current CVS code. Anyone? Anyone? -Luis ---...--- "Going (...) (26 years ago, 20-May-00, to lugnet.robotics.rcx.legos)
|
| |
 | | Interface B & Lego Engineer
|
|
Is anyone using the Lego Dacta Interface B and the Lego Engineer Plug-in to Robolab 2.0? Can the interface B source enough current to actually drive 8 motors? Does Lego Engineer/Interface B provide all the functions that Robolab 2 does with the RCX? (...) (26 years ago, 20-May-00, to lugnet.robotics)
|
| |
 | | Question Droid Developer Kit
|
|
I am writing assembly instructions for a person that is totally blind. These are for the Droid Developer Kit. The person will not be able to experience the digital display. My question is "does the display default to a certain program number when it (...) (26 years ago, 20-May-00, to lugnet.robotics)
|
| |
 | | Re: lnp communication question
|
|
(...) Ok, this brings up more questions :). I have never had any problems with errors when sending messages. Sometimes the message is not recieved but when it is, I have never seen any errors in the transmission. Am I missing your point? Second, (...) (26 years ago, 20-May-00, to lugnet.robotics.rcx.legos)
|
| |
 | | Sharp analog distance sensor
|
|
Greetings, I've looked, but don't seem to be able to find any relevant info. How does one hook up one of these beasts to the handyboard? I remember reading something somewhere that a track needs to be cut to do this - something I would like to avoid (...) (26 years ago, 20-May-00, to lugnet.robotics.handyboard)
|
| |
 | | Re: Quick Q : 9v Motors
|
|
(...) There's a big difference - some of the details are here: (URL) Baum (26 years ago, 20-May-00, to lugnet.robotics)
|
| |
 | | Re: IR communication PC <-> brick with NQC
|
|
(...) The RCX uses a special packet protocol which involes a lot of binary (non-ASCII) bytes, so controlling it with Hyperterminal won't work very well. Your best bet is to either write your own code to send the packets of the serial port or just (...) (26 years ago, 20-May-00, to lugnet.robotics.rcx.nqc)
|
| |
 | | Re: Is there a compatible h8 assembler for forth words?
|
|
(...) A good rule. I just know I'm going to need fast so I am planning ahead. Somehow I'm usually at the bleeding edge of trying to squeeze everything possible out of limited hardware. I originally learned my Forth on a 68000 (Mac Forth on the (...) (26 years ago, 20-May-00, to lugnet.robotics.rcx.pbforth)
|
| |
 | | RE: Spirograph Formulas??
|
|
You might enjoy the book "Turtle Graphics" - (URL) - uses the Logo language to control robotic turtles - descibes everything not in the mathematics of analysis but in terms of local geometric movement. Not sure if it has spirograph in it or not, but (...) (26 years ago, 19-May-00, to lugnet.robotics)
|
| |
 | | RE: Is there a compatible h8 assembler for forth words?
|
|
(...) No there is not. That being said, it's pretty easy to write one...if you have the time. I fiddled around with it a bit and then gave up since the GNU tools worked pretty quick. It was strictly a time/value exchange. From bitter experience, (...) (26 years ago, 19-May-00, to lugnet.robotics.rcx.pbforth)
|