To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / *13621 (+20)
  Droid Dev. Kit, reprise
 
Well, I've built a small "droid" from it now. And I have to admit, since it is a Technic kit, it was fun. It is only a little smarter than a Technic kit that only has a motor because of its programs (such as they are) and the light detector - but, (...) (27 years ago, 20-Aug-99, to lugnet.robotics)
 
  Re: Droid Dev. Kit, reprise
 
(...) Well, A week or two back, when I was in Jacksonville, I had a nice conversation with a TRU store manager. He pulled up Mindstorms on his CRT and let me watch. Down at the bottom of the screen was a second something listed as 'RIS' (or (...) (27 years ago, 20-Aug-99, to lugnet.robotics)
 
  r/c servos
 
In response to the question about RC servos, I noted, while probing the signals on the I/O ports with a scope, that the motor power settings result in varying duty cycle square waves from 1:7 through 7:1 and finally full on as the parameter value (...) (27 years ago, 20-Aug-99, to lugnet.robotics)
 
  Re: [Off-Topic] Re: X10 X-Cam
 
<SNIP> (...) Actually I believe the software that comes with the "MP3 Anywhere" is something similar to Ampapod (URL) allows you to use the X10 Mouse Remote to control Winamp. Ampapod is strictly 9x/NT though. (...) X10 is the king of marketing (...) (27 years ago, 20-Aug-99, to lugnet.robotics)
 
  Re: r/c servos
 
I love the idea of controlling an R/C servo with the RCX, but I don't think it is possible with only software. On the other hand, a relatively simple circuit could be made to convert a duty cycle to a R/C servo signal. Is anyone out there interested (...) (27 years ago, 20-Aug-99, to lugnet.robotics)
 
  Re: r/c servos
 
If the pwm is really being controlled by an 8 bit counter, that might be fine for the servos. The current rcx output has a cycle time of 8mS and uses 1mS increments. If those are the top 3 bits, then the resolution is 5 bits worth or 0.03mS. This (...) (27 years ago, 20-Aug-99, to lugnet.robotics)
 
  Re: r/c servos
 
(...) It is a software-based PWM. The topic of controlling a servo with the RCX has been discussed before. Generating the pulse stream for a servo would not be too difficult with the RCX, assuming you program the H8 directly using e.g. LegOS or (...) (27 years ago, 20-Aug-99, to lugnet.robotics)
 
  Re: r/c servos
 
(...) To get rid of the speculation here, the PWM is controlled by a programmable timer that the code in ROM configures to generate an interrupt every 1 ms. Output for each of 8 power levels is stored in a small table of waveforms, with the 1 ms (...) (27 years ago, 20-Aug-99, to lugnet.robotics)
 
  RE: Droid Dev. Kit, reprise
 
Or could it be that new 2 in 2 out screen programmable (blue RCX) RIS? JT -----Original Message----- From: Ray Sanders [mailto:rsanders@gate.net] Sent: Friday, August 20, 1999 6:03 AM To: lego-robotics@crynwr.com Subject: Re: Droid Dev. Kit, reprise (...) (27 years ago, 20-Aug-99, to lugnet.robotics)
 
  RE: X10 X-Cam
 
Don't buy the X-10 system expecting to use it for robotics. Those 2.4Ghz transmitters are directional and therefore are not well suited for the robotics application. Go to Best Buy or shopping.com etc. and buy a 900Mhz transmitter/receiver (actually (...) (27 years ago, 20-Aug-99, to lugnet.robotics)
 
  I/R Strobe/Omnidirectional sender/receiver
 
Greetings all, Looking at some of the new posts like the conductor/piano player has got me to thinking about the multiple RCX interacting scenario. The biggest inefficiency to start with is having to direct the entire RCX toward the other one, have (...) (27 years ago, 20-Aug-99, to lugnet.robotics)
 
  Re: Droid Dev. Kit, reprise
 
(...) They'll probably do what LEGO wants them to do. LEGO appears to be fairly inflexible and uncreative and will probably stick to their normal policy. LEGO's normal policy seems to be to tell the store it has been discontinued and allow the store (...) (27 years ago, 20-Aug-99, to lugnet.robotics)
 
  Re: r/c servos
 
(...) If all you need to do is generate a pulse of a certain length, why can't you do something like this? Sleep(1); // synchronize with the centisecond timer Fwd(OUT_A, 7); Sleep(1); // 1/100 of a second Off(OUT_A); Sleep(2); // 2/100 of a second (...) (27 years ago, 20-Aug-99, to lugnet.robotics)
 
  Re: r/c servos
 
(...) I can't understand this. Can you correct your grammar so it is clear what you're saying the average servo needs? - Robert Munafo (URL) LEGO: TC+++(8480) SW++ #+ S-- LS++ Hsp M+ A@ LM++ YB64m IC13 (27 years ago, 20-Aug-99, to lugnet.robotics)
 
  Re: r/c servos
 
(...) The answer is pretty simple, actually. In order to control a servo, you need to use pulses whose lengths are on the order of 1-2 ms. The more steps you get in that range, the more servo positions you can use. NQC can't produce pulses as short (...) (27 years ago, 20-Aug-99, to lugnet.robotics)
 
  a correction! to r/c servo
 
Sorry about that! The resulting 0.03 mS pulse width increments would result in 5 degree increments in the position of the servo shaft. How about that? JB -- Did you check the web site first?: (URL) (27 years ago, 20-Aug-99, to lugnet.robotics)
 
  Re: r/c servos
 
(...) I think what John was trying to say was that pulse widths between 0.7 ms and 2.0 ms give servo rotations between 0 and 180 degrees. With 45 steps in that range, you can control the servo in 5 degree increments. Seems to me he was approximating (...) (27 years ago, 20-Aug-99, to lugnet.robotics)
 
  Re: r/c servos
 
okay.. how about this.. avg servo needs.. 60hz pulses.. 1.0ms pulse width = end point 1.5ms pulse width = middle of rotation 2.0ms pulse width = other end point that is the form of the data to the servo. so you need to out put pulses 60 times a (...) (27 years ago, 20-Aug-99, to lugnet.robotics)
 
  Re: r/c servos
 
(...) That doesn't make sense either. If a single step of 2.0 ms causes 180 degrees of rotation, then how does 45 steps allow you to control it 5 degrees at a time? (...) Are you saying that the servo actually operates in steps of one degree each? (...) (27 years ago, 20-Aug-99, to lugnet.robotics)
 
  RE: r/c servos and firmware
 
Ok, Here's my 2 cents on servos...read to the bottom if you are interested in helping to develop the code for this. The servo takes a 60Hz (approx) pulse width signal between 1 and 2 msec The pulses are fed into a little circuit that generates an (...) (27 years ago, 20-Aug-99, to lugnet.robotics)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR