 | | Creating a GBC for a train layout
|
|
We were talking about this off line, and I'd like to continue this discussion on-line. We're trying to figure out how to make a GBC that looks like it should be part of a train layout. (...) Right. (...) The problem is actually getting paint that (...) (19 years ago, 3-Jan-06, to lugnet.org.us.laflrc)
|
| |
| | Re: Creating a GBC for a train layout
|
|
(...) Agreed. (...) Yes. I've got this on most of my modules, but would develop it a lot more for a train layout. At ChiBots I even had one minifig who had fallen off of the top level, and was being held over the roiling ball stream below only by (...) (19 years ago, 4-Jan-06, to lugnet.org.us.laflrc)
|
| |
| | Re: Creating a GBC for a train layout
|
|
(...) Some clubs build 8 wide trains. We could be one. :) Actually, many the trains have decoration that sticks out that wide. I've had to make changes to the engines I'm using so they don't trigger the train sensor. That won't be a problem. (...) (...) (19 years ago, 4-Jan-06, to lugnet.org.us.laflrc)
|
| |
| | Re: Creating a GBC for a train layout
|
|
(...) Absolutely. I was thinking more along the lines of how many clubs could allow us to "rent track" through their layout if we used 8-wide? I'm still trying to figure out how to run two trains on one track and *ABSOLUTELY* not collide them - (...) (19 years ago, 4-Jan-06, to lugnet.org.us.laflrc)
|
| |
| | Re: Creating a GBC for a train layout
|
|
(...) You need to drop the idea of using the "Horta eggs". Unless you can suppily enough for everyone to replace the soccer balls. Mixing the really nice, realistic balls (which are a different size) with soccer balls will only cause the stream of (...) (19 years ago, 4-Jan-06, to lugnet.org.us.laflrc)
|
| |
| | Re: Creating a GBC for a train layout
|
|
(...) Well, I've got 50, but I get your point. At just 20 cents a ball off-the-shelf at Meijers, they're not too bad compared to soccer balls on Bricklink... except that we already have 1000's of soccer balls in circulation free. (...) A very good (...) (19 years ago, 4-Jan-06, to lugnet.org.us.laflrc)
|
| |
| | Re: Creating a GBC for a train layout
|
|
(...) The latest idea was to have one RCX control train detection and switching (off the main line) for up to three stations and have another RCX for each station (load/unload/train-control) Each "siding" RCX would have to make sure it doesn't put (...) (19 years ago, 4-Jan-06, to lugnet.org.us.laflrc)
|
| |
| | Re: Creating a GBC for a train layout
|
|
(...) If we stay with the current 6-wide cars that we have (with the 8-wide sensing mechanism) would there be a problem with other 8-wide trains triggering the touch sensors and triggering the GBC sidings? I can't remember much about the 8-wide (...) (19 years ago, 5-Jan-06, to lugnet.org.us.laflrc)
|
| |
| | Re: Creating a GBC for a train layout
|
|
[crossposting to .trains to get some feedback, so limit LafLRC discussion to on-topic on this thread] (...) I don't know, but it's a question that we might like answered before we go too much further with this. Understand we can always limit things (...) (19 years ago, 5-Jan-06, to lugnet.org.us.laflrc, lugnet.trains)
|
| |
| | Re: Creating a GBC for a train layout
|
|
--SNIPPED-- (...) I can't answer the question but it might be useful if you could do up a CAD diagram of the sensor and train mechanisms for easy reference. I'm afraid I can't really understand what you mean here. It would also give a way of (...) (19 years ago, 5-Jan-06, to lugnet.org.us.laflrc, lugnet.trains)
|
| |
| | Re: Creating a GBC for a train layout
|
|
In lugnet.org.us.laflrc, Timothy Gould wrote: -SNIP- (...) Here's a link to the rendering of the train car we're asking about. (URL) The blue 2x2 round bricks slung between the train wheel sets is what we're concerned about. In this 6-wide train (...) (19 years ago, 6-Jan-06, to lugnet.org.us.laflrc, lugnet.trains)
|
| |
| | Re: Creating a GBC for a train layout
|
|
(...) Well, if the GMLTC 8-wide trains were involved, it would definitely be "mutilate, in a spectacular crash"... (URL) Here's one of my 8-wide locos> But, I'd suggest just go with what works for you. If an 8-wide train doesn't work, don't run (...) (19 years ago, 6-Jan-06, to lugnet.org.us.laflrc, lugnet.trains, FTX)
|
| |
| | Creating a GBC for a train layout, chapter 2
|
|
Another apect I was recently thinking about is where tracks usually cross baseplates. For instance, is it "easier" to get a straight section right next to the edge of a 32x32 baseplate, or six studs away? Or eight? Or... what? Does this always have (...) (19 years ago, 13-Jan-06, to lugnet.org.us.laflrc, lugnet.trains, FTX)
|
| |
| | Re: Creating a GBC for a train layout, chapter 2
|
|
(...) Parallel tracks usually have eight studs between them, because that's the spacing you get when you add a siding. It's also the spacing you get if you put cross tracks across them. In fact, the 16x16 cross track is the best piece to work out (...) (19 years ago, 13-Jan-06, to lugnet.org.us.laflrc, lugnet.trains, FTX)
|
