 | | Re: Variants of 4.5v / 12v train motors
|
|
(...) I checked my motors again, only one per type (I didn't want to dismantle all my locomotives that use the motors). Here are my measurement results: x570c01 (blue): Outer plug diameter: 5 mm Inner plug diameter: 2.1 mm Plug height: 2.1 mm (...) (20 years ago, 16-Jul-04, to lugnet.cad.dev)
|
| |
| | Re: Blender LDraw support
|
|
(...) Part detection is problematic due to changes over time in the library. For reference, LDView uses the following to identify parts: File is in the Parts directory, and isn't a descendent of any other parts at the time the file is loaded (sub (...) (20 years ago, 15-Jul-04, to lugnet.cad.dev)
|
| |
| | Re: LDRAWPREDIRS LDRAWPOSTDIRS - additional search paths
|
|
(...) Directory separators were added in DOS 2, which accepted both / and \ for that purpose. The feature was imitated from Unix. At the time, there also appeared a config.sys setting for *switch* character, which would default to / but could be set (...) (20 years ago, 15-Jul-04, to lugnet.cad.dev)
|
| |
| | Re: Variants of 4.5v / 12v train motors
|
|
(...) Would you be able to take a critical look at the sizes of the connector studs and the holes in them. There is a suggestion that these differ between the versions designed to work with the old Blue 2-pin connectors ((URL) those which fit the (...) (20 years ago, 15-Jul-04, to lugnet.cad.dev, lugnet.trains)
|
| |
| | Re: Blender LDraw support
|
|
(...) Well, I'm a bit further along now. No MPD support yet, but it'll be easy to add. It now supports hierarchical loading with piece recognition, loading even the Masakari model in a tolerable amount of time. In the process I noticed not all parts (...) (20 years ago, 15-Jul-04, to lugnet.cad.dev)
|
| |
| | 2003-2004 LSC Annual Report
|
|
LSC Annual Report August 2003 - July 2004: During this period of time the LSC handled the following issues to completion: - A location was established on the ldraw.org website listing all of the current LDraw library updates. This page is script (...) (20 years ago, 15-Jul-04, to lugnet.cad, lugnet.cad.dev, lugnet.cad.dev.org.ldraw)
|
| |
| | Re: Blender LDraw support
|
|
(...) I'm not a Blender user. Yet. I would like MPD support if/when I start using Blender and your script. (20 years ago, 12-Jul-04, to lugnet.cad.dev)
|
| |
| | Blender LDraw support
|
|
I hope this isn't off topic for this list. I've begun writing some scripts for Blender to import (and eventually export) LDraw DAT files. Cropped screenshot of result (pieces 105, 10 and 73057): (URL) location (currently 5KB): (2 URLs) features: (...) (20 years ago, 12-Jul-04, to lugnet.cad.dev)
|
| |
| | Re: Variants of 4.5v train motors
|
|
(...) I just checked my motor cases. The Type I motor cases and Type 2 motor cases are NOT interchangable. To update a Type I motor to a Type II motor you need a Type II top case, a Type II bottom case and a Type II gearbox. (The gearbox is the (...) (20 years ago, 1-Jul-04, to lugnet.cad.dev)
|
| |
| | Re: Variants of 4.5v train motors
|
|
(...) The cases were also sold separately: (URL) Set 1215 which was only the lower half of a Type II housing. It allowed a user to change a Type I motor (an earlier version without the hole) into the updated Type II (with the centre hole). HTH, (...) (20 years ago, 30-Jun-04, to lugnet.cad.dev)
|
| |
| | Re: Variants of 4.5v train motors
|
|
(...) The Type I motor (x564c01) supports both the old style power pickup brick with the plugs at the front (URL) as well as the new style power pickup brick with the plugs at the rear. (URL) The Type II motor (x581c01) supports only the new style (...) (20 years ago, 29-Jun-04, to lugnet.cad.dev, FTX)
|
| |
| | Re: Variants of 4.5v train motors
|
|
(...) The actual motors (both 12V and 4.5V) were sold seperately as replacement packs, so users can screw open the case and replace the motor (either replacing a broken motor or replace a 4.5V motor with a 12V motor or vice versa). (URL) 12V (peeron (...) (20 years ago, 29-Jun-04, to lugnet.cad.dev, FTX)
|
| |
| | Re: Variants of 4.5v train motors
|
|
(...) Yes, including case is good. As Niels indicated, the 4 x 12 x 3 1/3 versions are openable with a screwdriver, allowing the actual motors to be replaced, so I think the term "Shortcut" is correct. The 4 x 12 x 4 version is glued, so I'll change (...) (20 years ago, 29-Jun-04, to lugnet.cad.dev)
|
| |
| | Re: Variants of 4.5v train motors
|
|
(...) I'm confused. Are these parts generally openable - are the actual motors removeable (by the average user)? If they are removeable, then the (shortcut) names should include "case", since they aren't actually the motor. If the motors are not (...) (20 years ago, 29-Jun-04, to lugnet.cad.dev)
|
| |
| | Re: Variants of 4.5v train motors
|
|
<SNIP> Thanks Niels for taking the time to research this. I have updated the part names based on this information - to remove the voltage designation and correct the dimensions. Regarding your comment "The parts look good, I only miss metal (...) (20 years ago, 29-Jun-04, to lugnet.cad.dev)
|
| |
| | Re: Variants of 4.5v train motors
|
|
(...) I have checked my collection of train motors (which has reached an amount of 9), including all three mentioned variants. (Please note that I have changed the order of the quoted lists from Chris' message) (...) Got this one in blue, with a (...) (20 years ago, 27-Jun-04, to lugnet.cad.dev)
|
| |
| | Variants of 4.5v train motors
|
|
Hi We have a collection of 4.5V train motors on the LDraw Parts Tracker, and I'd like some help sorting out the variants of this part. On the PT right now we have x579c01 (by Michael Heidemann) - (URL) - this is the 4x12x4 version x581c01 (by (...) (20 years ago, 26-Jun-04, to lugnet.cad.dev, lugnet.inv)
|
| |
| | Re: Primitive Generator program update
|
|
(...) I have been doing a little bit of work on the calculator. It is really overdue for a major overhaul. I was trying to impliment some other additions that have not worked out very well so far. (...) have you tried Ctrl+ins=copy, Shift+Ins=Paste, (...) (20 years ago, 23-Jun-04, to lugnet.cad.dev)
|
| |
| | Re: Primitive Generator program update
|
|
(...) ok. (...) Might need to job parts reviewers memories to this detail. (maybe this post will) (...) I have uploaded the update to the webpage; (URL) me know if that is any better, and if I caused any other bugs. I did not spend much time (...) (20 years ago, 23-Jun-04, to lugnet.cad.dev)
|
| |
| | Re: LDBoxer - Next Step and My Datsville Plans
|
|
(...) (snip) (...) I *am* working on it, though slowly :-( The idea is that you can specify any number of part directories, e.g.: <MODELDIR> <LDRAWDIR>\P <LDRAWDIR>\Boxer <LDRAWDIR>\Boxer\B <LDRAWDIR>\Boxer\B\A <LDRAWDIR>\Boxer\BB <LDRAWDIR>\PARTS (...) (20 years ago, 22-Jun-04, to lugnet.cad.dev)
|
