To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.trainsOpen lugnet.trains in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Trains / 24972
    Re: 10170 TTX Intermodal Double-Stack Car Preview —Larry Pieniazek
   (...) Long time readers may recall my repeated ranting against using stacked technic plates for the receivers of the pin on bogie plates. Same issue here, in my view. Apparently the design may possibly have room for improvement. Having the trucks (...) (19 years ago, 4-May-05, to lugnet.trains, FTX)
   
        Re: 10170 TTX Intermodal Double-Stack Car Preview —Bryan Kinkel
     (...) technic (...) What is a better approach? Can you provide a link? -- Bryan "Larry Pieniazek" <larry.(mylastname)@...e.DOT.com> wrote in message news:IFyz9B.1sDD@lugnet.com... (...) seems the (...) (URL) >> (URL) (...) axle, to (...) click in (...) (19 years ago, 4-May-05, to lugnet.trains)
    
         Re: 10170 TTX Intermodal Double-Stack Car Preview —Larry Pieniazek
     (...) Only use one plate, and leave the second (upper) layer hollow so the pin can move up and down vertically and also move a bit out of the vertical axis. This helps with track conformance when the track is uneven. Note that if you use LEGO's (...) (19 years ago, 4-May-05, to lugnet.trains)
    
         Re: 10170 TTX Intermodal Double-Stack Car Preview —Bryan Kinkel
     Ah. The single plate approach is what I use as well for my custom cars. On first read, I thought you are advocating not using Technic plates at all. And I was trying to figure out what else could possibly be used (besides wagon plates.) My mistake. (...) (19 years ago, 4-May-05, to lugnet.trains)
    
         Re: 10170 TTX Intermodal Double-Stack Car Preview —Larry Pieniazek
      (...) whew! (...) Na, I like them. (...) One other thing I have toyed with is using a 1x2 technic brick, sideways. There is just enough of a cut in shoulder there that the pin doesn't bind the way it does in two plates. However it doesn't allow that (...) (19 years ago, 4-May-05, to lugnet.trains)
     
          Re: 10170 TTX Intermodal Double-Stack Car Preview —Samarth Moray
       (...) <Shameless Self-Plug> I'm doing the same thing with my newest under-construction diesel: (URL) This image is a bit outdated although it gives you an idea why I did so. I may/may not put pics of the updated version. It's all classified at the (...) (19 years ago, 4-May-05, to lugnet.trains, FTX)
     
          Re: 10170 TTX Intermodal Double-Stack Car Preview —Mathew Clayson
      (...) I used this part to atach a 9v train motor to a train baseplate, with the motor centered on the wire hole. I wanted the motor closer to the center for a My Train steam engine. Mat (19 years ago, 4-May-05, to lugnet.trains)
    
         Re: 10170 TTX Intermodal Double-Stack Car Preview —Ross Crawford
     (...) I have used both 2x2 and 4x4 turntables to attach bogies. The 2x2 allows for a good amount of movement from the vertical, but is a pig to re-attach the bogies if they come off. The 4x4 allows very little such movement, but as the MOC in (...) (19 years ago, 4-May-05, to lugnet.trains)
    
         Re: 10170 TTX Intermodal Double-Stack Car Preview —Samarth Moray
     (...) Random thought: Has anyone tried using Bionicle-style ball-and-socket joints as bogie attachments? My guess is that they would have enough friction to keep the stock from tilting over yet have the articulation to handle track unevenness as (...) (19 years ago, 4-May-05, to lugnet.trains)
   
        Re: 10170 TTX Intermodal Double-Stack Car Preview —John Neal
     (...) I can tell you that that probably is the best approach, especially when dealing with this sort of train car. My 5 well Huskey Stack: (URL) is a bear to set up, because I have to find the couplings blindly (2x2 turntables). Since it's been (...) (19 years ago, 4-May-05, to lugnet.trains, FTX)
   
        Re: 10170 TTX Intermodal Double-Stack Car Preview —Christopher Masi
   (...) [snip] (...) But it is prototypical, isn't it :?) Chris (19 years ago, 5-May-05, to lugnet.trains)
   
        Re: 10170 TTX Intermodal Double-Stack Car Preview —Larry Pieniazek
   (...) Oh, very much so! Even steam locomotive drivers (in most US prototypes I'm aware of) are held in place by gravity, much less individual freight car trucks. But they have a bit more weight to work with. Most model railroad models don't use this (...) (19 years ago, 5-May-05, to lugnet.trains)
   
        Re: 10170 TTX Intermodal Double-Stack Car Preview —Frank Filz
   (...) Of course for a 5 long unit car, having the trucks integral would make for a pretty unwieldy model... Frank (19 years ago, 6-May-05, to lugnet.trains)
 

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR