Results 541 560 of about 2200.
|
Search took 0.01 CPU seconds.
|
|
| | Forced to use IR Tower?
|
| Hi all, sorry if off-topic, but perhaps anybody knows if there is anyway to communicate with RCX through my laptop ir port. Actually I connect with my Palm through COM4, but when I set Bricxcc to this port says can't find robot. Thanks Francis (23 years ago, 12-Dec-01, to lugnet.robotics.rcx)
| |
| ir, tower (score: 2.934) |
|
| | Re: IR transmission, strange coding ?
|
| (...) I forget exactly how I measured this. I think maybe I hooked a scope directly to the LEDs then sent a constant stream of something to the tower and looked at the waveform on the scope. I don't remember noticing anything funny with the start (...) (23 years ago, 6-Nov-01, to lugnet.robotics.rcx)
| |
| ir, tower (score: 2.933) |
|
|
| ir, tower (score: 2.933) |
|
| | Re: What about this for a new RCX 2.5 setup?
|
| (...) What might be doable and best is a documented bus extension (a card plug-in) slot. This could be taken to the extreme by making a cpu unit that just has power (plug-in option of course) and memory (expandable of course) and maybe the IR or (...) (22 years ago, 13-May-02, to lugnet.robotics.rcx)
| |
| usb, ir (score: 2.933) |
|
|
| ir, tower (score: 2.932) |
|
|
| usb, long, tower (score: 2.931) |
|
| | Re: IR transmission, strange coding ?
|
| hi Kekoa, thanks for your answer, About the strange stop bit, I was wrong (John Barnes also mailed me about that, thanks John) it was indeed the parity bit. About the startbit (which is inverted to the data) I'm (almost) absolutly sure, I measured (...) (23 years ago, 6-Nov-01, to lugnet.robotics.rcx)
| |
| ir, tower (score: 2.930) |
|
| | Re: COLOR light sensor
|
| (...) I can own up to having done some work in this area. It isn't "available" yet because I haven't found an easily producible way to mount the LEDs yet. The device works as follows; The heart of the thing is a small PIC microcontroller which (...) (23 years ago, 28-Nov-01, to lugnet.robotics.rcx)
| |
| range, ir (score: 2.929) |
|
| | Re: Apparent 'time-out'
|
| The GUI version is 2.1.0. The pbForth version (COLD) is 2.1.2. I am using the USB tower with RIS 2.0. Once the RCX stops responding, if I pull out a battery and re-upload the firmware, the RCX will respond again to the same GUI session. In other (...) (22 years ago, 9-May-02, to lugnet.robotics.rcx.pbforth)
| |
| usb, tower (score: 2.924) |
|
| | Re: USB tower
|
| (...) Ghost is included with the 2.0 SDK - (URL) USB support is different on every platform. For platforms that Lego supported, I needed to work through their drivers - otherwise people would have to install one set of drivers for NQC, and another (...) (22 years ago, 10-Jun-02, to lugnet.robotics.rcx)
| |
| usb, tower (score: 2.923) |
|
| | RE: Apparent 'time-out'
|
| (...) One more bit of useful information would be the version of pbForth (which you get by typing COLD) and which version of the GUI (top left of window) Also, are you using the serial or USB tower? What messages were you sending to the RCX before (...) (22 years ago, 9-May-02, to lugnet.robotics.rcx.pbforth)
| |
| usb, tower (score: 2.922) |
|
|
| usb, tower (score: 2.921) |
|
| | LNPD: communication between clients
|
| It seems that when a client of lnpd sends data to the IR tower, these are not sent to the other clients connected to the daemon. Unfortunately, I really need this feature... So I tried to call "deliver_packet(tx_buffer, tx_end-tx_buffer);" in (...) (23 years ago, 28-Dec-01, to lugnet.robotics.rcx.legos)
| |
| ir, tower (score: 2.921) |
|
|
| usb, tower (score: 2.919) |
|
| | Re: startin with robolab
|
| Do you have the building parts to an Intelligent House set? Do you have the illustrated building instructions? Do you have a RCX and an IR Tower? Do you have the RoboLab software? (...) (23 years ago, 27-Dec-01, to lugnet.robotics.rcx.robolab)
| |
| ir, tower (score: 2.918) |
|
| | XP vs USB Tower and BrixCC
|
| Does BrixCC support the USB tower in Windows XP? I cannot seem to make mine work. I have reinstalled the program, but to no avail. Any ideas? -- Bob Fay THE SHOP (URL) (22 years ago, 20-Jul-02, to lugnet.robotics.rcx.nqc)
| |
| usb, tower (score: 2.917) |
|
| | Re: startin with robolab
|
| I have only the building parts to an Intelligent House set and the illustrated building instructions... I suppose I can download the Robolab software right? But my doubt is if I must buy the RCX and IR Tower. -- Paula Berger E-mail: (...) (23 years ago, 27-Dec-01, to lugnet.robotics.rcx.robolab)
| |
| ir, tower (score: 2.917) |
|
|
| usb, ir (score: 2.916) |
|
|
| usb, tower (score: 2.915) |
|
|
| usb, tower (score: 2.911) | More: Next Page >>
|