 | | Re: Sign of center pin on power adaptor
|
|
(...) You must be dealing with a different release of the battery pack than I am, since the only portion of the US instructions that mentions numbers states the output of the battery pack (10VAC, 7VA) and the approximate charge time (4 hours). There (...) (17 years ago, 12-Jul-07, to lugnet.robotics.rcx)
|
| |
| | Re: problem with the RCX
|
|
"Brian Davis" <brdavis@iusb.edu> wrote in message news:JL1oK5.K84@lugnet.com... (...) This might help! (URL) (...) (17 years ago, 12-Jul-07, to lugnet.robotics.rcx)
|
| |
| | Re: problem with the RCX
|
|
(...) Is the RCX still working? Does it "get hot" when it's running an unloaded motor? I would have thought that the 500 mA limit within the RCX case would prevent this, but perhaps it's marginal for some plastic piece "nearby". If the RCX is dead, (...) (17 years ago, 12-Jul-07, to lugnet.robotics.rcx)
|
| |
| | problem with the RCX
|
|
One of my students accidently left a tied up gear train running for a while, i.e. In the midst of running a RCX, the case not only gets very hot, but also has a very strong plastic burning smell. At first I thought it is due to the stuck gear train, (...) (17 years ago, 11-Jul-07, to lugnet.robotics.rcx)
|
| |
| | Re: Sign of center pin on power adaptor
|
|
(...) I agree. (...) The spec on the train AC adapter exactly matches the spec in the Li-Ion battery pack instructions. Jürgen (17 years ago, 11-Jul-07, to lugnet.robotics.rcx)
|
| |
| | Re: Sign of center pin on power adaptor
|
|
(...) Whoops, I missed that there was a third option. I concur with this, as it's both the right voltage and confirmed AC. The mA rating, BTW, is a capacity rating, so it will work for anything that draws 800mA or less. The NXT adapter is rated for (...) (17 years ago, 11-Jul-07, to lugnet.robotics.rcx)
|
| |
| | Re: Sign of center pin on power adaptor
|
|
(...) All my train PSUs are 10V AC, but are rectified and regulated to a nice 9V internally. (17 years ago, 11-Jul-07, to lugnet.robotics.rcx)
|
| |
| | Re: Sign of center pin on power adaptor
|
|
Usually AC will either say AC or have a ~ symbol. DC will either say DC or have a symbol that looks like = or _-_ -Rob A> (...) (17 years ago, 10-Jul-07, to lugnet.robotics.rcx)
|
| |
| | Re: Sign of center pin on power adaptor
|
|
(...) The AT&T 9v AC 800mA supply sounds just about right. (17 years ago, 10-Jul-07, to lugnet.robotics.rcx)
|
| |
| | Re: Sign of center pin on power adaptor
|
|
(...) _ALWAYS_ assume DC on an actual power adapter (at least in the US). Most AC devices will just use a simple cord, like you'd find on a portable stereo. A handful of devices will need AC power in a non-standard voltage and will use DC-like power (...) (17 years ago, 10-Jul-07, to lugnet.robotics.rcx)
|
| |
| | Re: Sign of center pin on power adaptor
|
|
(...) The one used for the RCX may be, but the NXT power supply is sold as a different item, and is listed as a 10VAC adapter vs. the 9VAC adapters used by trains and various other systems. Not that it matters unless you also buy the Li-Ion battery (...) (17 years ago, 10-Jul-07, to lugnet.robotics.rcx)
|
| |
| | Re: Sign of center pin on power adaptor
|
|
(...) I now have a Dynamic Instruments 16VAC 375mA, AT&T AC 9V 800mA, and a Black & Decker 9V 200mA from a Dust Buster but it does not say if it is DC or AC, I am assuming AC. Which one should I use? I am hoping the AT&T but the 800mA makes me a (...) (17 years ago, 10-Jul-07, to lugnet.robotics.rcx)
|
| |
| | Re: Sign of center pin on power adaptor
|
|
(...) It's the same PSU as used for the 9V train controllers. (17 years ago, 10-Jul-07, to lugnet.robotics.rcx)
|
| |
| | Re: Sign of center pin on power adaptor
|
|
(...) The wall wart for my RCX says "output 10.8VAC 700mA 8w" so it sounds like the rectifier is in the RCX, not the wall wart. (17 years ago, 10-Jul-07, to lugnet.robotics.rcx)
|
| |
| | Re: Sign of center pin on power adaptor
|
|
(...) Wow, I do not have a 10V AC adapter but I am sure I can get one at Radio Shack. Thanks a million, Tom (17 years ago, 10-Jul-07, to lugnet.robotics.rcx)
|
| |
| | Re: Sign of center pin on power adaptor
|
|
(...) I once came across a box full of old wall wart power supplies at a rummage sale and after digging through it for 10 minutes or so I found three that had 12V AC and the correct plug for the RCX. They work perfectly and I think I paid about $1 (...) (17 years ago, 10-Jul-07, to lugnet.robotics.rcx)
|
| |
| | Re: Sign of center pin on power adaptor
|
|
(...) 9V (orientation doesn't matter). But I wouldn't recommend it as there have been reports of burnt out rectifiers from people doing that. Hope this helps, ROSCO (17 years ago, 10-Jul-07, to lugnet.robotics.rcx)
|
| |
| | Sign of center pin on power adaptor
|
|
I am looking for the sign of the center pin on the RCX 1.0 power adaptor plug. I have a DC 9v 200ma transformer and want to plug it into the RCX but I do not know what the sign is on the center of the plug. It looks like the rush on buying the old (...) (17 years ago, 10-Jul-07, to lugnet.robotics.rcx)
|
| |
| | RCX Code - Light Raw Values
|
|
Hi people, Its possible to configure/read RAW light sensor values with RCX CODE? I think i saw it sometime ago, but i could not find it. Thanks in Advance Patrick J. Levy ___...___ Omiccron Programação Gráfica Ltda. 11 3288-4832 (...) (17 years ago, 30-Jun-07, to lugnet.robotics.rcx)
|
| |
| | Alternate firmware upload from MacOSX
|
|
Hi all, We're trying to wrap up our alternative runtime for the RCX (first), and soon the NXT. I am struggling, however, to upload our firmware from the Mac using a USB tower. I can upload using a serial or USB tower from both Windows and Linux... (...) (17 years ago, 10-Jun-07, to lugnet.robotics.rcx)
|
