 | | expansion board of rug warrior
|
|
Hi all, I have installed an expansion board on rug warrior. Do I need to download/include any specific library for it or it will work fine with previous libraries of Rug Warrior. Thanks Regards Javaid Iqbal (26 years ago, 30-Mar-99, to lugnet.robotics.handyboard)
|
| |
| | Re: GCC 2.8.1 for HC11
|
|
Great, everything I need is there, thanks a lot. ---...--- (...) what (...) nice (...) to (...) student (...) (26 years ago, 30-Mar-99, to lugnet.robotics.handyboard)
|
| |
| | H-board/Expansion board seperate battery question.
|
|
Hello everyone... I have an expansion board attached and working just fine on my Handy board and wish to accomplish the following... Create a separate power source of 12v, using a small 2-4 amp hour rechargeable battery from radio shack, to the (...) (26 years ago, 29-Mar-99, to lugnet.robotics.handyboard)
|
| |
| | Help
|
|
Hi Friends, i need the most simple circuit for the conection of the hc11, thanks. ___...___ Do You Yahoo!? Get your free @yahoo.com address at (URL) (26 years ago, 29-Mar-99, to lugnet.robotics.handyboard)
|
| |
| | Re: GCC 2.8.1 for HC11
|
|
(...) I'm extrememly surprised. It was sort of a no-brainer when I did it and I've never had a problem on any number of weird systems. Please keep us updated. --Ken (26 years ago, 29-Mar-99, to lugnet.robotics.handyboard)
|
| |
| | Re: GCC 2.8.1 for HC11
|
|
(...) At the above link. That one appears to be an HC11 emulator with some nice features. I haven't played with it much yet. I think it might be able to single-step on the target machine also? Go look at the link above, and then knock of a directory (...) (26 years ago, 29-Mar-99, to lugnet.robotics.handyboard)
|
| |
| | Re: GCC 2.8.1 for HC11
|
|
(...) 'Cuz I couldn't get it to compile. I suppose I could have tried some other flavors of Linux, or Solaris, but I'd rather start from something newer, therefore the excitement in finding a new port. (...) Thanks a bunch! I think... Once it is (...) (26 years ago, 29-Mar-99, to lugnet.robotics.handyboard)
|
| |
| | Re: Help needed!
|
|
(...) Marc, First of all, using IC, or probably any form of programming, takes patience. If you mess around with IC3.2 long enough, you will eventually get it to run. Try messing with port speeds, etc. There is nothing wrong with your Handy Board! (...) (26 years ago, 29-Mar-99, to lugnet.robotics.handyboard)
|
| |
| | Re: GCC 2.8.1 for HC11
|
|
Excuse me, but I ' ve already heard this "wookie"...so many times, but what is it ? If it's an reditor, can you say me where can I find a copy ? ---...--- (...) Hornstein <kenh@cmf.nrl.navy.mil>; Dave Yoest <dyoest@splat.gsfc.nasa.gov> (...) set (...) (26 years ago, 29-Mar-99, to lugnet.robotics.handyboard)
|
| |
| | Re: Java class libraries for HandyBoard
|
|
Thanks a lot, I was just looking for this. Stefano Falconetti ---...--- (...) (26 years ago, 29-Mar-99, to lugnet.robotics.handyboard)
|
| |
| | Re: GCC 2.8.1 for HC11
|
|
(...) How come you didn't simply use the 2.6.3 cross-compiler? I doubt the optimizer is improved _that_ much for the HC11. (...) It was a while ago, and I don't remember how much of Carlos's work is left. It all had to be converted to the new (...) (26 years ago, 29-Mar-99, to lugnet.robotics.handyboard)
|
| |
| | Help needed! Additional info
|
|
Hi everybody! Will Bain alerted me that I was using the wrong library files. I've corrected this, but am still having the "board not responding" problem! Any help on this is still very much welcome!! Thanks and best regards, Marc msmkatz@wxs.nl (...) (26 years ago, 28-Mar-99, to lugnet.robotics.handyboard)
|
| |
| | Re: Polaroid Sonar Device fried!!!!
|
|
(...) The most common causes would probably be: (1) Not having a transducer hooked up when the ping is initiated; (2) Having the flat flex cable plugged in backwards (you can't trust the stripe to be on the correct side! Make sure pin 1 goes to (...) (26 years ago, 28-Mar-99, to lugnet.robotics.handyboard)
|
| |
| | Re: Help needed!
|
|
MSMKatz wrote: <snip> (...) <snip> Marc, I wonder if the hardware is perfectly ok, but you're inadvertently attempting to load the wrong software. I'm not sure where your lib_hs.lis came from or why IC automatically loads it, but I think it might be (...) (26 years ago, 28-Mar-99, to lugnet.robotics.handyboard)
|
| |
| | Polaroid Sonar Device fried!!!!
|
|
The C3279 chip ("Q1") on my sonar device fried. I checked the expansion board and it is assembled correctly. I am not sure why it would fry. I added the 0.1uF electrolytic capacitor to C7 position as stated in the sonar.html site and suggeted by an (...) (26 years ago, 28-Mar-99, to lugnet.robotics.handyboard)
|
| |
| | Java class libraries for HandyBoard
|
|
Users interested in running Java on HandyBoard can now download demonstration application and a set of library class files at (URL) Gasparik (26 years ago, 28-Mar-99, to lugnet.robotics.handyboard)
|
| |
| | Help needed!
|
|
Hi, I have assembled my recently bought Handy Board kit and have run into major problems: In paragraph 6.0.5 of the assembly manual, the Handy Board is tested for the microprocessor and memory circuits. After powering up the board and running IC (...) (26 years ago, 28-Mar-99, to lugnet.robotics.handyboard)
|
| |
| | Re: Handy Board inputs
|
|
Hi Becky, If you are using the HB with the expansion board, you *do* need new library files loaded. Check the web site at: (URL) easiest way to run new library files is to edit lib_hb.lis to include them. To test the HB inputs w/o the expansion (...) (26 years ago, 27-Mar-99, to lugnet.robotics.handyboard)
|
| |
| | Handy Board inputs
|
|
Hi, my name is Becky Browning. I am currently working on building a robot using the Handy Board. I am having considerable troubles though getting either the digital or analog inputs to work. Right now I have analogs ports 0 and 1 working with (...) (26 years ago, 27-Mar-99, to lugnet.robotics.handyboard)
|
| |
| | analog inputs on expansion board
|
|
Hi, Two questions: 1) When I plug a Lego reflectance sensor into the expansion board it seems to work fine. When I use the angle sensor it seems to work fine. When I plug them in at the same time the angle sensor stops working. No change to the (...) (26 years ago, 27-Mar-99, to lugnet.robotics.handyboard)
|
