 | | Re: Darn those definitions (was: The new Super Car)
|
|
(...) easy (...) Like I said, everything is compressible, with the probable exception of the stuff in a black hole. Even the exclusion principle (the law that controls elecron 'orbits' round an atom) is reconed to be overcome by sufficient force (...) (27 years ago, 9-Aug-99, to lugnet.robotics)
|
| |
 | | Re: Lego is like nanomachines
|
|
Robert Munafo wrote in message ... (...) a (...) mechanical (...) design. (...) Being serious, this wouldn't work. Scaling down would call for different structures. Eric (27 years ago, 9-Aug-99, to lugnet.robotics)
|
| |
 | | Re: Mechanical question
|
|
This thread already offers a lot of interesting explanation about the thrack slip, but on the wheels part you may want to have a look at: (URL) in menu: going in circles Animations explain how side slip in wheels is (practically) zero as long as (...) (27 years ago, 9-Aug-99, to lugnet.robotics)
|
| |
 | | RE: Handy Board software
|
|
(...) They're both really decent 8bit micros. Similar IO capabilities, and I think the HC11 has better timers, but only 8 bit A/D. I've worked a LOT with the HC11 and it's really a good part. (...) Beleive it or not, there is a FORTH for the HC11 (...) (27 years ago, 9-Aug-99, to lugnet.robotics, lugnet.robotics.rcx.legos)
|
| |
 | | Re: Using the Motor as a Tachometer
|
|
(...) SNIP (...) SNIP (...) Todd, The danger as I see it is not electrical but physical. If the sensor mode of the input port is "active" the port will provide power to the motor (sensor). Thus you could have 2 motors either working together or (...) (27 years ago, 9-Aug-99, to lugnet.robotics)
|
| |
 | | RE: Using the Motor as a Tachometer
|
|
(...) In fact, this is how the RCX motor controller internally sets the motor up for "brake" instead of "off"... Cheers, Ralph Hempel - P.Eng ---...--- Outside of a dog, a book is a man's best friend. Indside of a dog, it's too dark to read... (...) (27 years ago, 9-Aug-99, to lugnet.robotics)
|
| |
 | | Re: Power steering for 8448
|
|
(...) Good point! Well I'll have to change my model a bit then - the rotation sensor should not go onto the motor axle, but onto the axle driving the rack (stilled geared I guess). Hmm, what can I use this touch sensor for now?? An extra bumper (...) (27 years ago, 9-Aug-99, to lugnet.robotics)
|
| |
 | | Re: Using the Motor as a Tachometer
|
|
(...) Try to short circuit the motor used as tarcometer / generator, and you'll see. Also try preventing the second motor from spinning, and you'll experience the same thing. About efficiency: this is not what you are experiencing, but the motor (...) (27 years ago, 9-Aug-99, to lugnet.robotics)
|
| |
 | | Re: Power steering for 8448
|
|
(...) I wouldn't say /just/ for steering. And in fact I only use in input, since the touch sensor can be connected in parallel with a light sensor or such thing. The touch sensor is by the way only used during initialization, when the outer limits (...) (27 years ago, 9-Aug-99, to lugnet.robotics)
|
| |
 | | Re: Using the Motor as a Tachometer
|
|
In fact, if you hook up two motors using the black cords and turn one of them, the increased voltage will cause the other one to turn without any physical effort applied to it. That's pretty rad. I'm not sure if I understand the brake concept? Could (...) (27 years ago, 9-Aug-99, to lugnet.robotics)
|