 | | Re: Something else is needed, I think...
|
|
(...) I think new firmware is a good way to go. I would vote for a completely new byte code, perhaps similar in spirit to the original, but designed fresh from the ground up. There is no source for the current firmware, although there is pseudocode (...) (28 years ago, 3-May-99, to lugnet.robotics)
|
| |
 | | Re: Something else is needed, I think...
|
|
I think that a good solution would be to have Legos work as a true operating system that stayed loaded in the brick and would accept downloading compiled programs for it to run. Maybe the firmware replacement idea that has been tossed around could (...) (28 years ago, 3-May-99, to lugnet.robotics)
|
| |
 | | Re: Something else is needed, I think...
|
|
(...) If you believe you have good ideas for a language, my opinion is that you should propose something to the list, find people who want to work with you on this (assuming you don't want to work alone), ignore the people who say you know nothing (...) (28 years ago, 3-May-99, to lugnet.robotics)
|
| |
 | | Re: Something else is needed, I think...
|
|
(...) I am not sure how much you can extend the capabilities of the firmware while maintaining its basic dispatch loop. There are some very basic design constraints that would be difficult to change without redoing all of the firmware. If you (...) (28 years ago, 3-May-99, to lugnet.robotics)
|
| |
 | | Re: Something else is needed, I think...(long)
|
|
In article <000101be94cb$a8fd58...a@pro150>, Ralph Hempel <rhempel@bmts.com> writes (...) My QBasic program available from www.phesk.demon.co.uk/lego/ can download the Lego firmware from DOS - where can I find your new firmware to test it with, (...) (28 years ago, 3-May-99, to lugnet.robotics)
|
| |
 | | Re: LEGO light sensor schematic
|
|
(...) OK, I fixed that and in the process discovered they should be PNPs. 3Hp83 is a BC857 GP PNP from Philips. Looks better now. (...) I think photo diode used in photovoltaic mode. It looks like it pushes the voltage down from that established by (...) (28 years ago, 3-May-99, to lugnet.robotics)
|
| |
 | | Re: LEGO light sensor schematic
|
|
(...) Ah... much better, I figured one or two components were backwards. Just to clean up the schematic a bit you could flip R1 (75R) to the right side of the Q4. I would also bring R8 (12R) in line with the LED. This would then be a more standard (...) (28 years ago, 3-May-99, to lugnet.robotics)
|
| |
 | | Re: Something else is needed, I think...
|
|
(...) we must definitely remain compatible (at least partially) with Spirit.ocx protocols. (...) outside world with endless possibilities, and processing power that it will never be able to match! (...) already been done for us. And please, do not (...) (28 years ago, 3-May-99, to lugnet.robotics)
|
| |
 | | Re: Something else is needed, I think...
|
|
(...) I don't know if you guys realize this but if anything like this is ever done we must definitely remain compatible (at least partially) with Spirit.ocx protocols. The Spirit.ocx control is a HUGE bonus we must not throw away!! It makes possible (...) (28 years ago, 3-May-99, to lugnet.robotics)
|
| |
 | | Re: Something else is needed, I think...
|
|
(...) I agree on this point. I've been forced to move to legOS not by intrinsic NQC limitations but by those imposed by the RCX firmware. I still prefer to use RcxCC/NQC when I don't need legOS: programs load much faster, it's a pleasant and (...) (28 years ago, 3-May-99, to lugnet.robotics)
|