To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / 3096 (+20)
  Flexible axles!!!!
 
I've got a tip for everyone: In the ZNAP box 3552 are two appr. 20 cm long FLEXIBLE AXLES included. It also contains a 9v technic motor. I bought the boxes because they were cheaper than ordering single motors from lego and the axles were a pleasant (...) (28 years ago, 22-Jan-99, to lugnet.robotics)
 
  Re: legOS
 
I dunno.. that's why I'm askin... -----Original Message----- From: Kekoa Proudfoot <kekoa@pixel.Stanford.EDU> To: lego-robotics@crynwr.com <lego-robotics@crynwr.com> Date: Friday, January 22, 1999 8:43 PM Subject: Re: legOS (...) up.. (...) -- Did (...) (28 years ago, 22-Jan-99, to lugnet.robotics)
 
  Re: Sensor monitoring
 
I'm new here and don't have much experience yet with the RCX, but I was just wondering... Is it possible to attach both sensors to a single input using one of the multi-input multiplexers (voltage divider arrangements) that I've read about on here? (...) (28 years ago, 22-Jan-99, to lugnet.robotics)
 
  Re: Sensor monitoring
 
(...) You can multiplex simple switchs that way, but not the light sensor. I requires power and outputs an analog value. (28 years ago, 22-Jan-99, to lugnet.robotics)
 
  navigation with compass
 
(...) Light sensor with a magnifier? :-) I tried using the differential gear to "remember" the initial heading of my robot, and painfully discovered that the result would drift off after many turns. Now I think compass is the way to go. (I wonder (...) (28 years ago, 22-Jan-99, to lugnet.robotics)
 
  (canceled)
 
 
  (canceled)
 
 
  (canceled)
 
 
  Re: is Mindstorm/RCX Y2K Compliant???
 
(...) microcontroller in the RCX does this, or not. Jasper (28 years ago, 22-Jan-99, to lugnet.robotics)
 
  Re: Flexible axles!!!!
 
what exactly is znap? thanks! -- Chris Stanley cstanley@usit.net (...) (28 years ago, 22-Jan-99, to lugnet.robotics)
 
  Re: RCX 2.0 -- ideas.
 
(...) The big cost in these things, wqould be that you need 5 of the 2*2*2/3 plates at the end of Technic leads, unless you homebrew those too. AFAIK, you can only get leads, at least as far as Service packs are concerned, for about $5-$6 (with 2 (...) (28 years ago, 22-Jan-99, to lugnet.robotics)
 
  Re: expansion ports
 
(...) Reductio ad absurdam: You buy, say, 8880. You lose one of the, say, #12 axles. You replace with 2 #6 and an axle extender. You sell it on (bad move, IMHO, but hey, it could happen :) ). By your reasoning, you now have sold a product, not made (...) (28 years ago, 22-Jan-99, to lugnet.robotics)
 
  Re: Smooth Plates
 
(...) Set 6567 Speed Splasher has two red 1*8 tiles. It is available under $2.50, generally. But don't tell your SO, or you won't be able to buy a few multiples of 8277 :) (just bought two myself, over the last few days... I now have a _really_ (...) (28 years ago, 22-Jan-99, to lugnet.robotics)
 
  Re: Squishy Brick
 
(...) Is that the page where there is a 1*4 grey technic beam, pierced by a #3 or 4 axle, with a 16-tooth bevel (?) gearon one side, and a washer on the other? I think they put that picture in all Technic sets, to tell you that the axles have to be (...) (28 years ago, 23-Jan-99, to lugnet.robotics)
 
  Re: homebrew Temp sensor
 
(...) Hmm.. why no elco? that is, if you make sure you alway plug your sensor on in the same way, you should get a constant +ve and -ve... Mindstorms does use the standar measuring trick of having DC current run thru the resistor, right? Jasper (28 years ago, 23-Jan-99, to lugnet.robotics)
 
  Re: The Handyboard (was Re: RCX 2.0 -- ideas.)
 
(...) How about using a few large plates (of the type found as baseplates in small to medium sets), and a few basic bricks, possibly with the addition of glue to keep it all together? Jasper (28 years ago, 23-Jan-99, to lugnet.robotics)
 
  Re: expansion ports
 
Jasper Janssen wrote in message <36a90add.169456990@...et.com>... (...) Your examples are irrelevant because they probably don't still have active patents on the pieces and may or may not have ever had patents on all of them. What I was talking (...) (28 years ago, 23-Jan-99, to lugnet.robotics)
 
  NQC 1.1 b1
 
Due to feature creep, NQCC 1.0 never got out of beta. I've merged nqcc and the various utiltites (rcxfirm, rcxlog, etc) into a single program called nqc, and added some minor improvements to the compiler as well. The command line has changed quite a (...) (28 years ago, 23-Jan-99, to lugnet.robotics)
 
  Re: homebrew Temp sensor
 
Jasper Janssen wrote in message <36a914e5.172025205@...et.com>... (...) Right, you could use an electrolytic if you wanted to make sure you always plugged your sensor the right way. Many people who are in this group do not know the subtleties of (...) (28 years ago, 23-Jan-99, to lugnet.robotics)
 
  Re: The Handyboard (was Re: RCX 2.0 -- ideas.)
 
(...) But that would do nothing towards making it truly LEGO electric compatible; coming up with a suitable compartment for the motherboard that leaves room for the expansion board, even if it's not actually connected yet; leaving the display and (...) (28 years ago, 23-Jan-99, to lugnet.robotics)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR