To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / 3021 (+20)
  Sensor monitoring
 
I have a project that I am building, it is a finish line monitor for a pinewood derby track. What I am doing is putting two light sensors above the track pointing down so the ambient light will change when the car crosses the finish line. One sensor (...) (28 years ago, 20-Jan-99, to lugnet.robotics)
 
  Re: Sensor monitoring
 
To my knowledge the LEGO firmware executes one instruction at a time for each task, so there is one and only one instruction being executed at a certain instant even if you have multiple tasks. Because NQC uses the LEGO firmware, I don't think you (...) (28 years ago, 20-Jan-99, to lugnet.robotics)
 
  Re: Voltage generator
 
In article <Pine.GSO.3.96.99012....uen.org>, jeff <jeff@uen.org> writes (...) Wait for a calm day and mount it 3 ft above a car, or on the front of a bike with a speedometer. Make several runs in opposite directions at constant speed and take the (...) (28 years ago, 20-Jan-99, to lugnet.robotics)
 
  Re: Dacta in Canada? (Was Re: Differentials also available from LegoDacta)
 
The catalog from Spectrum that I have seen has all the Technic related Dacta Service Packs. (...) of (...) I can clear up the "unlikely" scenario that you mentioned. if you tell me what you are looking for, I will just look in the catalog and tell (...) (28 years ago, 20-Jan-99, to lugnet.robotics)
 
  Re: Voltage generator/Anemometer
 
In article <Pine.GSO.3.96.99012....uen.org>, jeff <jeff@uen.org> writes (...) Measuring the voltage would be more accurate. (28 years ago, 20-Jan-99, to lugnet.robotics)
 
  Re: Dacta in Canada? (Was Re: Differentials also available from LegoDacta)
 
(...) The most recent S@H catalog for Canada was over 50 pages, and more than half of the sets listed were new. Granted, they use large flashy layouts, but would you really want to have a lego catalog in the style of Digi-Key (who can put 450 (...) (28 years ago, 20-Jan-99, to lugnet.robotics)
 
  Re: Voltage generator
 
(...) I figure it would take quite a gale to turn over the gear motor with any degree of accuracy, but you might be able to rig something with the rotation sensor and a model airplane prop. Daniel "Dan'l" Miller Senior, School of Aeronautics and (...) (28 years ago, 20-Jan-99, to lugnet.robotics)
 
  Re: Sensor monitoring
 
(...) I think the sensors are read every 3ms and the value stored somewhere. I don't think they are read just when you ask for them in software. You get the last value read. I base this on the way the rotation sensor and some of the sensor modes (...) (28 years ago, 20-Jan-99, to lugnet.robotics)
 
  Rover (was Voltage Generator)
 
List, I just sent the message below to Linc and not to the whole list as it may be marginal on the Topic issue. Ben has asked about it too and others may. So I'm sending this now. I do still talk about Lego in this but further discussion may be too (...) (28 years ago, 20-Jan-99, to lugnet.robotics)
 
  Re: Voltage generator
 
Daniel, Peter Hesketh posted a similar suggestion, and yes the motor may be too firm for the job. I'll play around and do some testing, this week or as I can get time. Then I'll post the results. My goal is to end up with a pure Lego anemometer or (...) (28 years ago, 20-Jan-99, to lugnet.robotics)
 
  Re: Dacta in Canada? (Was Re: Differentials also available from LegoDacta)
 
(...) I don't know about this catalog, but DACTA has traditionally had a *ton* of sets, when you look at their entire range from DUPLO, BASIC/FreeStyle, Early Technology (probably not the official name), Technic-level science kits, robotics sets (...) (28 years ago, 20-Jan-99, to lugnet.robotics)
 
  Pictures of lego-scanner
 
I have updated my web-page with pictures of my lego-scanner and of Vector Rover, my bot implementing proximity detection that keeps track of its angular rotation like a logo turtle using a FOS light unit. (URL) Svale Skogsrud; Producer, (...) (28 years ago, 20-Jan-99, to lugnet.robotics)
 
  Re: Sensor monitoring
 
according to the sdk, all tasks are run in parallel, with each task being visited round-robin and executing one instruction. this would mean they are not being monitored at *exactly* the same time, but i would think a tight loop in two tasks (...) (28 years ago, 20-Jan-99, to lugnet.robotics)
 
  Re: Dacta in Canada?
 
(...) We digress from the original question. (which is so often the case. Threads seem to take on a life of their own here, don't they? :) To re-iterate, how can a person in Canada who is not afilliated with an educational facility get a LEGO/Dacta (...) (28 years ago, 20-Jan-99, to lugnet.robotics)
 
  Re: Dacta in Canada?
 
Follow this thread back to the reference for Spectrum Canada. They sell to individuals as well as schools. (At least they sold to me last week and are shipping the merchandise to my home.) rob (...) (28 years ago, 21-Jan-99, to lugnet.robotics)
 
  Re: Help! Can't talk to IR Tower with Mac w/nqcc!
 
(...) That wiring looks fine, provided that "IR" is a DB-9 female that connects directly to the IR device. If you use the IR cable supplied by lego, then you'll need to swap pins 2 and 3. Mac pins 1 and 2 (RS-232 pins 7 and 8) are not required at (...) (28 years ago, 21-Jan-99, to lugnet.robotics)
 
  Re: Direction of rotation sensor.
 
(...) Here's a thought: A rubber band around the axle to check and a pulley with a peg in it. In one direction, the pulley/peg run into the touch sensor and the band then starts slipping on the axle (hopefully geared down enough to sufficiently push (...) (28 years ago, 21-Jan-99, to lugnet.robotics)
 
  Re: Homebrew Rotation Sensor
 
I've added a circuit diagram for something that comes close to making voltages that look like a real LEGO Rotation Sensor. It's not perfect yet. The RCX may loose a few counts here and there. I think I need a better Opamp than the old LM324. (URL) (28 years ago, 21-Jan-99, to lugnet.robotics)
 
  Any interest in an RCX simulator?
 
I have been considering working on an RCX simulator for use with NQC programs. I'd be willing to develop the core simulator itself if others were willing to do the user interface work. I'll make sure the simulator is as portable as NQC currently is (...) (28 years ago, 21-Jan-99, to lugnet.robotics)
 
  Re: Help! Can't talk to IR Tower with Mac w/nqcc!
 
Success!! On the advice of Ben Kimball I started looking for an extension that might be competing for the serial port. My system is also used for MIDI and I found the MIDI Manager extension. I disabled it and rebooted and found that I could now talk (...) (28 years ago, 21-Jan-99, to lugnet.robotics)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR