 | | Light outputs on RCX
|
|
Has anyone ran lights from the RCX outputs? I need something brighter than an LED, any ideas? Thanks, Bryan Bible --- __o --- __o Tandem Computers --- _ \<,_ --- _ \<,_ Austin Texas --- (*) / (*) --- (*) / (*) bryan.bible@compaq.com -- Did you check (...) (28 years ago, 18-Jan-99, to lugnet.robotics)
|
| |
 | | Re: Light outputs on RCX
|
|
(...) I took apart a laser pointer. I put the laser module into a mutilated brick. I added a diode, an LM-317, appropriate resistors and a .1uF capacitor to make a 3 volt power supply. The diode makes it so the laser is on for motor forward, off for (...) (28 years ago, 18-Jan-99, to lugnet.robotics)
|
| |
 | | Re: Light outputs on RCX
|
|
Paul Haas writes: > On Mon, 18 Jan 1999, Bible, Bryan wrote: > > > Has anyone ran lights from the RCX outputs? I need something brighter than > > an LED, any ideas? > > I took apart a laser pointer. I put the laser module into a mutilated > brick. I (...) (28 years ago, 18-Jan-99, to lugnet.robotics)
|
| |
 | | Where is "R4" on Handy Board Extension Schematic?
|
|
I have just finished building the extension board, and, while it appears to work all right, I can't seem to find resistor R4 on the schematic. The power transistor near the on/off switch is getting quite hot with the expansion board piggybacked on (...) (28 years ago, 18-Jan-99, to lugnet.robotics)
|
| |
 | | Re: new Throwbots
|
|
(...) I doubt that these joints will be of much use - they're way to rigid, and there is not a real good place to attach a motive link. (28 years ago, 18-Jan-99, to lugnet.robotics)
|
| |
 | | Re: Light outputs on RCX
|
|
(...) I made several diffrent color (even flashing!) lights with the mini xmas lights. they are real bright if you set the output to 8 or they work at any level. I took the bulb out of the little plastic holder and soldered wires to the wires on the (...) (28 years ago, 18-Jan-99, to lugnet.robotics)
|
| |
 | | Re: new Throwbots
|
|
(...) I just bought 2 of the new throwbots, Granite and Electro. I am not very impressed. The best part about them is the colored gears. Only because I am tired of gray. ---...--- @¿@ (URL) ,-, Follow the adventures of Capt. Jack Napalm! One thing (...) (28 years ago, 18-Jan-99, to lugnet.robotics)
|
| |
 | | Re: RCX 2.0 -- ideas.
|
|
(...) As a first step, how about simple 2 *4 s with logic gates in them? one of the connectors below for power, one output below, and two inputs on top :) Jasper (28 years ago, 18-Jan-99, to lugnet.robotics)
|
| |
 | | Re: RCX 2.0 -- ideas.
|
|
(...) Whereas I have lost it several times form turning the RCX off.. a real pain. Jasper (28 years ago, 18-Jan-99, to lugnet.robotics)
|
| |
 | | RE: RCX 2.0 -- ideas.
|
|
(...) Actually I'd be happy with just some Lego resistors, a 2X1 plate with the two studs as contacts and a resistor between them :) 100% pure multiplexed touch sensors Oh well. -- Did you check the web site first?: (URL) (28 years ago, 18-Jan-99, to lugnet.robotics)
|
| |
 | | Re: LOGO with Mindstorms
|
|
(...) Are the exotic sensors (rotation temperature, as described in the RCX program thing) available yet? if so in which sets, or is it just at Dacta? Jasper. (28 years ago, 18-Jan-99, to lugnet.robotics)
|
| |
 | | Re: FLASHING LIGHT ON LCD PANEL?
|
|
So using the Lego software I ran a small prg that reset all the variables. I still have that flashing quarter circle. do I need to reset it in NQC? and if so a sample code might help. Chris the guy with the lego brick tattoo or visit my lego walker (...) (28 years ago, 19-Jan-99, to lugnet.robotics)
|
| |
 | | Re: Seeking Strategies on Humanoid Robots/Walkers [DAT]
|
|
(...) I seem to recall that noone has succesfully solved the problem of artificial biped locomotion even in traditional robotics, let alone within the constraints of LEGO. Basically, what you need is a system that can sense very delicate shifts in (...) (28 years ago, 19-Jan-99, to lugnet.robotics)
|
| |
 | | Re: is Mindstorm/RCX Y2K Compliant???
|
|
(...) It's a microcontroller. Therefore it has an internal clock. Therefore it can suffer from Y2K, if it hasn't been removed. (...) No it's not. We're not even close to getting everything away. How do you think we will fare if the world's (...) (28 years ago, 19-Jan-99, to lugnet.robotics)
|
| |
 | | Off topic [was Re: is Mindstorm/RCX Y2K Compliant???)
|
|
(...) The most likely scenario is that so many people are in such a tizzy about Y2K that there will be runs on banks throughout the civilized world before the end of the year, causing total economic collapse. Ignorance, not computer bugs, are the (...) (28 years ago, 19-Jan-99, to lugnet.robotics)
|
| |
 | | Expression limitations w/bytecode
|
|
As I understand it, the bytecode interpreter doesn't allow you to do fairly simple things like subtract two variables from each other. That makes doing comparisions between sensors somewhat challenging if you want to know the magnitude of the (...) (28 years ago, 19-Jan-99, to lugnet.robotics)
|
| |
 | | Re: Expression limitations w/bytecode
|
|
(...) The firmware does support basic arithmetic operations. You can use them in NQC like this... int a, b; task main { a = IN_1; b = IN_1; b -= a; } Dave p.s. As a side note, NQC does not support stuff like "a=b+c", but this is due to concurrency (...) (28 years ago, 19-Jan-99, to lugnet.robotics)
|
| |
 | | Re: is Mindstorm/RCX Y2K Compliant???
|
|
(...) No, just because it has a microcontroller in it doesn't mean it will stop working in 2000. Russell is absolutely right. If it doesn't know what the year is (you never tell it) it doesn't know when Y2K is going to happen. There are too many (...) (28 years ago, 19-Jan-99, to lugnet.robotics)
|
| |
 | | RE: is Mindstorm/RCX Y2K Compliant???
|
|
This is getting way out of hand... (...) If it doesn't know what year it is, then it can't have a Y2K problem! And even if it would know about the year, and even if there was a Y2K bug, I don't think it would matter much. In the worst case, your (...) (28 years ago, 19-Jan-99, to lugnet.robotics)
|
| |
 | | Re: FLASHING LIGHT ON LCD PANEL?
|
|
(...) The simplest solution is to reload the firmware. You can use the Lego software to do this. I'm almost positive you can reset if from inside NQC, but since I don't use NQC, I can't give you sample code. -Kekoa (28 years ago, 19-Jan-99, to lugnet.robotics)
|