 | | Crate Contraption Writeups
|
|
I didn't want to post a writeup of the recent crate contraptions we've done until I had some video to show. Unfortunately all the video I took at NWBrickCon in October had really messed up audio. Last weekend we showed a nearly identical setup, (...) (22 years ago, 31-Mar-05, to lugnet.org.us.smart, lugnet.robotics) !
|
| |
 | | Re: caster wheel design
|
|
Thanks everybody for the answers, but i think i will give up with the caster... The robot will be very heavy... i think it wont work.. I will go to a synchro drive aproach... Thanks. Patrick "Patrick Levy" <omiccron@uol.com.br> escreveu na mensagem (...) (22 years ago, 31-Mar-05, to lugnet.robotics)
|
| |
 | | Re: I2C bus for Lego RCX
|
|
$36 before the discount that is almost 30% off Nitin (...) (22 years ago, 31-Mar-05, to lugnet.robotics)
|
| |
 | | Re: caster wheel design
|
|
I had a similar problem once, when my Cybot had a broken castor - I found that the Lego axle made a snug fit in the cavity intended for it - however it was bending and under a lot of tension. My solution was to use axle-joiners((URL) and 2 unit long (...) (22 years ago, 31-Mar-05, to lugnet.robotics)
|
| |
 | | Re: caster wheel design
|
|
(...) heck I ended up with any of them. They work great however. (22 years ago, 31-Mar-05, to lugnet.robotics)
|
| |
 | | Re: caster wheel design
|
|
(...) This the one you mean? (URL) (22 years ago, 31-Mar-05, to lugnet.robotics)
|
| |
 | | Re: caster wheel design
|
|
(...) You can actually do that one better - use a 2x2 plate with offset wheel holder on the bottom, & you can dispense with the 2x3 plate. I browsed Peeron & Bricklink and couldn't locate it, but they're handy for microcasters. (22 years ago, 31-Mar-05, to lugnet.robotics)
|
| |
 | | Re: Alternate connectors
|
|
You even do not need to cut your existing LEGO wires visit (URL) cost effective too Nitin (...) (22 years ago, 30-Mar-05, to lugnet.robotics, FTX)
|
| |
 | | Re: Alternate connectors
|
|
(...) One of the NALUG members did the very thing you are talking about. I believe he used a connector from Radio Shack but I will double check or have him check the forums. Mike (22 years ago, 30-Mar-05, to lugnet.robotics, FTX)
|
| |
 | | Alternate connectors
|
|
I am trying to find a suitable connector that will let me cut up and extend the regular mindstorm wires, as well as to connect to custom built sensors. I have seen that some people have used (URL) Molex connectors> (URL) but I can't seem to find (...) (22 years ago, 30-Mar-05, to lugnet.robotics, FTX)
|
| |
 | | Re: caster wheel design
|
|
(...) Another "microcaster" is the style used in "ERBIE the Robocar" discussed here (URL) made with a 2x2 turntable, a 2x3 plate, and a single wheel (URL) works surprisingly well, so long as 1) The weight isn't huge and 2) the surface isn't too (...) (22 years ago, 30-Mar-05, to lugnet.robotics)
|
| |
 | | Re: caster wheel design
|
|
(...) Move the other wheels or the CG so that the caster doesn't support much weight. No matter what your design, a caster that carries a lot of weight will not work well. The large turntables will have a lot of friction when carrying a lot of load. (...) (22 years ago, 30-Mar-05, to lugnet.robotics)
|
| |
 | | Re: I2C bus for Lego RCX
|
|
OK, that's neat! That's a novel way to attach to bricks and electrical connectors. Is the $36 before or after the $10 discount ? Either way, I'll probably be buying one to play with. -JSM (...) (22 years ago, 29-Mar-05, to lugnet.robotics)
|
| |
 | | Re: caster wheel design
|
|
If you are planning on running on smooth surfaces, you might be suprised at how well your robot drives and turns with just one of those domed 2x2 'gliders' instead of a wheeled caster. ---...--- Steve Baker ---...--- HomeEmail: (...) (22 years ago, 30-Mar-05, to lugnet.robotics)
|
| |
 | | Re: caster wheel design
|
|
(...) How heavy is this? A caster needs an offset, but making this offset as small as possible should reduce bending. I usually use a medium pulley on a #3 axle; either end of the axle is held in the pin hole of a Technic crossblack, while short (...) (22 years ago, 30-Mar-05, to lugnet.robotics)
|
| |
 | | caster wheel design
|
|
Hi, I´m tring to build a robot that may use a caster wheel, But i am running some serious problemes in it design. If I use an axle or pin for the caster, it will bend. (the robot is quite heavy). So i tried to use a turntable as a caster axle, but (...) (22 years ago, 30-Mar-05, to lugnet.robotics)
|
| |
 | | Re: I2C bus for Lego RCX
|
|
(...) Very nice job as usual... as I told you before, I really love your PCB to RCX electrical connectors! (...) Special mention to your Wink Kit (URL) very cool introduction to LEGO sensors building! Philo ...not affiliated in anyway to Mindsensors (...) (22 years ago, 30-Mar-05, to lugnet.robotics)
|
| |
 | | Re: Robolab as a tool for teaching programming
|
|
(...) Note that the LEGO Company appears to agree strongly with you. From a press release I just read: ---...--- NEWS RELEASE March 28, 2005 NI today announced The LEGO Company uses the NI LabVIEW graphical development environment and NI (...) (22 years ago, 29-Mar-05, to lugnet.robotics)
|
| |
 | | Re: GBC 6 - the obsession continues...
|
|
(...) Well, until the video is uploaded, here are some of my pictures from the event (after moderation): (URL) link showing the whole thing: (URL) And as Iain I'd like to know what's inside the black box! Ahh, but that was truly the beauty of (...) (22 years ago, 29-Mar-05, to lugnet.robotics)
|
| |
 | | I2C bus for Lego RCX
|
|
Some thing Extremely new :-) I2C bus interface for RCX. Now we can connect any I2C device to RCX. You can use SRF08 or SRF10 with RCX very easily without tampering your RCX Have look at (URL) lot of new things at www.mindsensors.com Nitin (22 years ago, 29-Mar-05, to lugnet.robotics)
|