 | | Re: adder-subtractor update
|
|
And maybe the "d" in add? (...) (25 years ago, 19-Jan-01, to lugnet.robotics)
|
| |
| | Re: adder-subtractor update
|
|
Forgot the 'l' of html ;) (URL) C." <lego-robotics@crynwr.com> wrote in message news:3.0.6.32.200101...gtlinux... (...) be (...) well (...) (25 years ago, 19-Jan-01, to lugnet.robotics)
|
| |
| | Re: adder-subtractor update
|
|
(...) At 06:36 16-01-2001 GMT, mike fusion wrote: (...) (URL) ? :) mc. (25 years ago, 19-Jan-01, to lugnet.robotics)
|
| |
| | robolab/rcx/scout/send mail command
|
|
i have an rxc, a scout and a copy of robolab 2 for macintosh (i don't have any instruction books for robolab). i understand that it is possible to send commands from the rcx to the scout and receive replys. could any one give me a quick start (...) (25 years ago, 19-Jan-01, to lugnet.robotics)
|
| |
| | Re: Vision command & macintosh
|
|
(...) That is what it seems to be. (...) You can't use a logitech camera with the Lego software, but you can use the lego camera with the logitech SDK though there is no SDK for macintosh systems. Take a look at question No. 7 at (URL)I have no (...) (25 years ago, 19-Jan-01, to lugnet.robotics)
|
| |
| | Re: Vision command & macintosh
|
|
(...) I believe that someone said that whilst the Lego camera is made by Logitech, it has a different USB identifier or some such thing - that made it so you couldn't interchange Lego and Logitech cameras with the same software. I have no firsthand (...) (25 years ago, 19-Jan-01, to lugnet.robotics)
|
| |
| | Re: adder-subtractor update
|
|
One question: What is the URL? -- Bob Fay California, USA rfay@we.mediaone.net (URL) (25 years ago, 19-Jan-01, to lugnet.robotics)
|
| |
| | Re: adder-subtractor update
|
|
please take me off the list. I just don't have the time to read all of it Thanks (25 years ago, 18-Jan-01, to lugnet.robotics)
|
| |
| | adder-subtractor update
|
|
my site has been updated today, added a new chassis which has a shorter gearing (less gear lashing) but is one brick higher. it is still shorter than a motor any questions? mike (25 years ago, 18-Jan-01, to lugnet.robotics)
|
| |
| | Re: Vision command & macintosh
|
|
(...) I had heard that the actual camera was a Logitech QuickCam, but I could find no Mac drivers on their site that will work with the Lego camera. Any ideas? John (25 years ago, 18-Jan-01, to lugnet.robotics, lugnet.robotics.rcx)
|
| |
| | Re: Sharing USB cable between IR and VC?
|
|
(...) 1. The "hub" inside the camera will not help you unless it actually has additional "ports" on it. It's probably a one port "USB Hub" which is present as a result of logitech using someone else's USB solution instead of developing a custom (...) (25 years ago, 18-Jan-01, to lugnet.robotics)
|
| |
| | Re: RCX Firmware (was: Remote dead, what to do?)
|
|
(...) Thanks for the clarification. So... am I correct to assume that there is some portion of the RCX firmware that is not accessable for update/replacement? This would be the portion that describes/controls the 'built-in functions? Thanks again, (...) (25 years ago, 18-Jan-01, to lugnet.robotics)
|
| |
| | Re: Remote dead, what to do?
|
|
(...) Correct, the Remote requires Firmware in the RCX. (...) No. It needs the Firmware to set up the IR port to receive the commands. The Built-in programs will run without firmware with the RUN Button. (...) The SCOUT always has it's firmware. (...) (25 years ago, 18-Jan-01, to lugnet.robotics)
|
| |
| | RE: Cable length
|
|
You mean the 9-pin cable for the IR tower, right. Yes, you can use a much longer cable. Get one with one female (holes) and one male (pins) connector, and you should be OK. You have to use it on the computer end, because the tower only accepts a (...) (25 years ago, 18-Jan-01, to lugnet.robotics)
|
| |
| | Re: Remote dead, what to do?
|
|
(...) No, the Remote functionality requires (AFAIK) the RIS firmware. It won't work with the Robolab firmware which is different. (...) ?? Programs won't run w/o firmware of some kind. (...) The Scout wasn't designed to be used with a remote (...) (25 years ago, 18-Jan-01, to lugnet.robotics)
|
| |
| | Re: News sensors and the RDS
|
|
John Barnes wrote in message <4.2.0.58.2001011614...server>... (...) competition (...) I have an answer to this. You don't need a computer to program it and it's easier for younger children (or adults that don't want to get on the computer) to play (...) (25 years ago, 18-Jan-01, to lugnet.robotics)
|
| |
| | Re: Remote dead, what to do?
|
|
Will the Remote Control directly control the RCX output ports A - C without downloading firmware? Will it run the RCX built-in programs without downloading firmware? The output ports and built-in programs of the Scout from set 9735 Robotics (...) (25 years ago, 18-Jan-01, to lugnet.robotics)
|
| |
| | Re: Palmpilot and RCX
|
|
i have it at home, but i do have someone else's port of nqc to the palm, and the direct controller, i guess you can use the palm as a remote. actually it may be for windows ce, but i'll check all the same. m. "Sebastian Scherer" (...) (25 years ago, 17-Jan-01, to lugnet.robotics)
|
| |
| | RE: Sharing USB cable between IR and VC?
|
|
Probably not a good idea. First, unless you replace the cable on the camera, you'll have to roll it up and carry it on your robot. USB cables have a minimum length, so you need another rolled up USB cable carried on your robot to connect the tower (...) (25 years ago, 17-Jan-01, to lugnet.robotics)
|
| |
| | Re: Help/Advice How to buy certain bricks in the UK
|
|
I think Pitsco sells two big turntables for $10! JB (25 years ago, 17-Jan-01, to lugnet.robotics)
|
