 | | Re: NQC Code
|
|
Nancy, Sorry for not getting back sooner. Been outof town. Anyway, thanks for the reply. This is what I am looking for. I am going to combine this wirh another routine. Basicly 1. Right Touch Sensor hits object. RCount += 1; IF RCount >= 2 { RCount (...) (28 years ago, 9-Dec-98, to lugnet.robotics)
|
| |
 | | Re: NQC Code
|
|
Dave, Sorry for not getting back sooner. Been out of town. Anyway, thanks for the reply. This is what I am looking for. I am going to combine this wirh another routine. Basicly 1. Right Touch Sensor hits object. RCount += 1; IF RCount >= 2 { RCount (...) (28 years ago, 9-Dec-98, to lugnet.robotics)
|
| |
 | | Bot-Kit 1.0 Released
|
|
I am pleased say that I have now been able to release Bot-Kit 1.0 which provides an interface between MindStorms/Cybermaster and the Smalltalk programming language. This is available for download from (URL) This link also contains more information (...) (28 years ago, 10-Dec-98, to lugnet.robotics)
|
| |
 | | Re: Delphi developers
|
|
John: I haven't heard about Delphi, but some have created other ways to program the RCX. See my Mindstorms page and look under the Alternate Programming Environments section. The page is located at (URL) Nelson nelsonb@vii.com (...) (28 years ago, 10-Dec-98, to lugnet.robotics)
|
| |
 | | Re: RCX Command Center
|
|
Found the problem. I normally run code like this from the D: drive. It seems that unless I have the NQC dir on the C: then it can not find "Command.com". Once I moved the NQC to the C: and remapped my icon, then it alled worked. Would it be (...) (28 years ago, 9-Dec-98, to lugnet.robotics)
|
| |
 | | unsuscribe
|
|
unsuscribe (28 years ago, 10-Dec-98, to lugnet.robotics)
|
| |
 | | ...-help@...
|
|
(28 years ago, 10-Dec-98, to lugnet.robotics)
|
| |
 | | -help@
|
|
(28 years ago, 10-Dec-98, to lugnet.robotics)
|
| |
 | | autostart of program in mindstorm
|
|
You can use my free RCX Command Center. You can select the program, run it or stop it, and even run individual tasks. (Of course, it also does a lot more.) See my web page for more info: (URL) Overmars (...) (28 years ago, 10-Dec-98, to lugnet.robotics)
|
| |
 | | Communicating with IR tower
|
|
The standard way for doing this is to use variable 0 on the RCX. Te robot can set it to a specific valu when it needs something. The PC can use the SetEvent command and the VariableChange event handler to check whether the variable changes. (...) (28 years ago, 10-Dec-98, to lugnet.robotics)
|
| |
 | | Delphi developers
|
|
RCX Command Center was written in Delphi using the spirit.ocx. It work very easy. (Only note that the On command to switch motors on is called On_ because on is a reserved word in Delphi.) But if you want to write programs to download to the RCX, I (...) (28 years ago, 10-Dec-98, to lugnet.robotics)
|
| |
 | | CM: MotorCurrent
|
|
For the Cybermaster unit, it is possible to monitor the current of the external motor, measured in milliamps. I assume this can be used to detect when the motor is stalled. Do anybody know the typical values of MotorCurrent when the motors is o (...) (28 years ago, 10-Dec-98, to lugnet.robotics)
|
| |
 | | Re: Communicating with IR tower
|
|
Hi John, I've been doing this for a while with the Cybermaster. You can simple use the SetVar and Poll commands in immediate mode via the OCX to read and set variables in the brick. Add a bit of handshaking and you have a communications mechanism (...) (28 years ago, 10-Dec-98, to lugnet.robotics)
|
| |
 | | effect of motor speeds
|
|
I noticed that settting the motor speed does not seem to have much efect on the speed the robot is moving: 0 = slow 1 = faster 2 = slighly faster than 1 3-7 = about equal to 2 Am I doing something wrong? Or is this standard behavior? Mark Overmars (28 years ago, 10-Dec-98, to lugnet.robotics)
|
| |
 | | Re: CM: MotorCurrent
|
|
I only made one test with it, and by the looking at the results I couldn't tell if the motor running loaded, but I may be wrong! The result of the function seems to be: .If no motor is attached, the result is zero. .If a motor is attached and not (...) (28 years ago, 10-Dec-98, to lugnet.robotics)
|
| |
 | | Re: CM: MotorCurrent
|
|
(...) Yes, this sounds plausible. My comment on stall detections was probably wrong. Fredrik (28 years ago, 10-Dec-98, to lugnet.robotics)
|
| |
 | | Re: effect of motor speeds
|
|
(...) I think so, most problematical is the reduction in starting torque, free running always seems to peak at the same RPM. With an Acrobot based robot I have problems with wrinkles in the carpet stopping it when manoevering at low speed, but it (...) (28 years ago, 10-Dec-98, to lugnet.robotics)
|
| |
 | | Re: effect of motor speeds
|
|
(...) I think it depends a lot on the weight of the robot and the type of mobility used. For instants, when I use tracks on my CyberMaster, 1 is very very slow and 7 is fast. All the other numbers between have speeds more or less according to this (...) (28 years ago, 10-Dec-98, to lugnet.robotics)
|
| |
 | | Re: effect of motor speeds
|
|
Humm... I think I switched the legends. Laurentino Martins (...) (28 years ago, 10-Dec-98, to lugnet.robotics)
|
| |
 | | Re: Communicating with IR tower
|
|
(...) Have you already done this? (detect out of range situations?) I'd really would like to know how did you do it! I also have a CyberMaster and I'm working with NQCC and with the Spirit.OCX in VC++. Thanks! Laurentino Martins (...) (28 years ago, 10-Dec-98, to lugnet.robotics)
|