 | | ROVER
|
|
Dear Mr Fred Martin, I hope you remember that we in India were making a rover ,which in the end ran into some problems.We had to present the inoperational rover only for the exhibition. Now,after the exhibition we are trying to make the rover work. (...) (28 years ago, 2-Feb-99, to lugnet.robotics.handyboard)
|
| |
 | | Re: what variety of 6811 can be used?
|
|
Hi! (...) Hi Steve! I've put my hb to work yesterday, but I think I can help you a bit. The "FN" means the chip has "plcc" package, while the "P" would mean it's DIP package. The plcc is the one used in the Handy Board, as you can see the 52 pins (...) (28 years ago, 2-Feb-99, to lugnet.robotics.handyboard)
|
| |
 | | Re: what variety of 6811 can be used?
|
|
(...) why does the 512 bytes matter? the HB has 32K of external ram. i guess if you're planning to do rom-able code development then i understand. there's very little difference between the e and a series. the port A counter/timer pins are slightly (...) (28 years ago, 2-Feb-99, to lugnet.robotics.handyboard)
|
| |
 | | Pneumatic 6 legged walker
|
|
For those of you interested in pneumatics I've finally completed a pneumatic 6 legged walker. Included on the page is a small .avi so you can see it walk. CU Bert Visit my site on Lego, Robot's and Visual Basic at (URL) you check the web site (...) (28 years ago, 2-Feb-99, to lugnet.robotics)
|
| |
 | | Re: Pneumatic 6 legged walker
|
|
Thank you... Have you built pneumatic robots as well? Have you been able to make them strong enough to carry a compressor? CU Bert Visit my site on Lego, Robot's and Visual Basic at (URL) bericht----- Van: Barfoot, William: <bbarfoot@tosco.com> Aan: (...) (28 years ago, 2-Feb-99, to lugnet.robotics)
|
| |
 | | Re: 2 servos
|
|
(...) Sure is! Check out this page on the HB web site: (URL) Will , , __@_/ \_@__ |/ | /__, o @_/ )\ ) ( \ (\/\\, ~~~...~~~ ' ` ~~~...~~~ ` ~~~...~~~ Wendy Parson, You can't say civilization isn't advancing; Will Bain, in every war they kill you in (...) (28 years ago, 2-Feb-99, to lugnet.robotics.handyboard)
|
| |
 | | Re: Navigation and PID ressources for Handy Board
|
|
(...) Francois, That's right, I was trying to use the PID for a control system but I finally gave up due to the small power supply from its motor outputs. The last time I browsed the HB web I did found some articles in the mail list, maybe you can (...) (28 years ago, 2-Feb-99, to lugnet.robotics.handyboard)
|
| |
 | | Motor outputs
|
|
Dear all, I asked this question before but I might have used the wrong wordings. Here I try again. As you all know, the HB 's motor outputs give PVM, however, it gave me problems when I tried to amplify the power (both current and voltage.) Is there (...) (28 years ago, 2-Feb-99, to lugnet.robotics.handyboard)
|
| |
 | | Re: 360 deg. swiveling electrical connection
|
|
I am not familiar with the cyberslam darts... Does it have to be electrical trigger (or are you planning to route something else - a sensor perhaps) ? If mechanical trigger is ok, perhaps you could use a lego axle up the center of the rotary joint. (...) (28 years ago, 3-Feb-99, to lugnet.robotics)
|
| |
 | | Re: Variations on the "ADDER SUBTRACTOR" ("differtrans" ?)
|
|
Hey Russell..check out my Geo page..no popup, no obnoxious banner..but hey..I'm sneaky... (...) Joe Greene Technical Support OpenDisc Systems, Inc. Boulder, Colorado, 80301-2442 USA 303-546-0460 Joe_Greene@OpenDisc.Com (28 years ago, 3-Feb-99, to lugnet.robotics)
|
| |
 | | Re: Adder/Subtractor revisited
|
|
Ahh, I see. I thought you meant to power the primary diff in the A-S transmission in this fashion. Yes, a third diff coupled carrier-to-carrier with the primary one in the A-S would work. Three diffs ! I don't think I have enough of them to model (...) (28 years ago, 3-Feb-99, to lugnet.robotics)
|
| |
 | | Re: Where to buy the Invention System?
|
|
(...) I live in China - and have been/am facing the same problem. Until now Mindstorms has only been on sale in Canada, UK and the US. February 1 it was launched in some other English speaking areas (amongst others in Hong Kong). Internet ordering (...) (28 years ago, 3-Feb-99, to lugnet.robotics)
|
| |
 | | RE: 360 deg. swiveling electrical connection
|
|
The other options is to use a wire but not allow the turret to turn more than 180degrees either side of center, if you are at 179 and wish to go to -179 you have to go all the way back around rather than just nipping across those 2degrees. It's (...) (28 years ago, 3-Feb-99, to lugnet.robotics)
|
| |
 | | Re: Where to buy the Invention System?
|
|
(...) (URL) shipped mine to Spain with no problem. Best Pedro Jorge (28 years ago, 3-Feb-99, to lugnet.robotics)
|
| |
 | | Re: Expansion Board Files
|
|
Doug Are you using the freeware version of IC or the Newton labs version of IC. I just downloaded the latest expansion board library files and I get the following Synchronizing with board Pcode version 3.10 present on board Loading (...) (28 years ago, 3-Feb-99, to lugnet.robotics.handyboard)
|
| |
 | | Re: LCD screen source
|
|
A few years back I got an Optrex DMC16249 LCD from Digikey (URL) Look for Digikey part no.73-1037-ND . I just checked there web site and they still have the same part. The Optrex LCD is a perfect fit for the HB John (...) (28 years ago, 3-Feb-99, to lugnet.robotics.handyboard)
|
| |
 | | legOS & C
|
|
Cygwin B20.1 legOS 0.16 Whenever I try to do a declaration initialization of an array: int thing[] = {0x01,0x02,0x03}; I get a failure on linking: "undefined reference to memcpy" The code compiles and runs fine when compiled for x86. I can always (...) (28 years ago, 3-Feb-99, to lugnet.robotics)
|
| |
 | | Problems with servo function
|
|
Hi all, I'm new to the list, handyboards, IC, and robotics, but I'm not totally clueless so bear with me... So I got an HB from Pat Hui, and it seems to work fine. I've been able to write a program that will vary a beep tone and print variable (...) (28 years ago, 3-Feb-99, to lugnet.robotics.handyboard)
|
| |
 | | Re: Expansion Board Files
|
|
(...) I finally got back to this ... had to go to the day job ... :) (...) ... and everything loads just fine now. Thanks Fred, for this and everything that you are doing. I'm just getting into this stuff but so far I am having a blast. -- Doug (28 years ago, 3-Feb-99, to lugnet.robotics.handyboard)
|
| |
 | | Re: legOS & C
|
|
(...) What compiler are you using? I was unable to duplicate this behavior with egcs-1.1 -- for static integer arrays it outputs .word pseudo-ops and for automatic arrays that small it generates inline code to initialize each element. In any case, (...) (28 years ago, 3-Feb-99, to lugnet.robotics)
|