 | | Order RCX seperately (new in online catalog)
|
|
I don't know if anyone has mentioned this yet, but it looks like the RCX is listed as an individual item on the Lego on-line catalog: (URL) havta call S@H and see what it costs. Hopefully, it's cheaper than through Pitsco. (28 years ago, 19-Dec-98, to lugnet.robotics)
|
| |
 | | Re: LCD configs (was:Suppliers and rf link)
|
|
john calhoun, Mine just arrived and they are 1 X 16 connectors. I ordered 2035TNLD/Y displays for $8.00 each. You might want to order now while they have the 2X16 displays with 1X16 connectors. I have soldered the connector on and tested it and its (...) (28 years ago, 19-Dec-98, to lugnet.robotics.handyboard)
|
| |
 | | Re: ROM stuff: Better than PWM
|
|
(...) In fact, I'm using exactly this algorithm to drive the motors for my laser scanner - though the host platform is an embedded PC, not the RCX. I'm currently rewriting the motor drivers to: * keep an 1ms resolution system clock * call the task (...) (28 years ago, 19-Dec-98, to lugnet.robotics)
|
| |
 | | RE: All-around-the-robot bump detection
|
|
There is an example on the net somewhere of building it just like this using the bend sensors ripped out of a Mattel PowerGlove. -Kerry -----Original Message----- From: Dennis Parker [mailto:dparker@onr.com] Sent: Friday, December 18, 1998 6:55 AM (...) (28 years ago, 19-Dec-98, to lugnet.robotics)
|
| |
 | | Re: Conductive Foam
|
|
Conductive foam is would be great, but press down on it a few times and watch it not return to its full shape. If you used it as a sensor, you have to have very low resolution, because it doesn't recover much. (...) (28 years ago, 19-Dec-98, to lugnet.robotics)
|
| |
 | | Re: All-around-the-robot bump detection
|
|
Like I said, just ideas, and I haven't yet woken up. Thoughts ? I like the pneumatic idea, but instead of using a cylinder, how about taking a piece of Lego tubing and bending it, so that when you have pressure in the system, the tube wants to (...) (28 years ago, 19-Dec-98, to lugnet.robotics)
|
| |
 | | Re: ROM stuff: Better than PWM
|
|
(...) Funny - I was thinking of doing exactly the same thing - and also basing it on Bresenham. I've always wondered about 1-bit D/A, but if you actually read the docco it is wrapped up in so much weird signal theory it is very hard to understand (...) (28 years ago, 19-Dec-98, to lugnet.robotics)
|
| |
 | | ROM stuff: Better than PWM
|
|
So I was thinking about writing a motor driver that is better than what is in the ROM already. Here's the problem: You have a function called once every 1/1000th of a second. You want to allow n speeds of the motor at minimal cost in lookup tables. (...) (28 years ago, 19-Dec-98, to lugnet.robotics)
|
| |
 | | Re: dc motor output control
|
|
Maybe you can put a series of diodes in series and in parallel but the other direction to reduce the voltage. H-bridge +- +- +- +- motor H-bridge -+ -+ -+ -+ Good luck, James (...) (28 years ago, 19-Dec-98, to lugnet.robotics.handyboard)
|
| |
 | | RE: urgent request help !!!!
|
|
What about the display board itself? Could it be that one of the SMT parts on the board is dead? Or a trace on the LCD is shorted? --phil (28 years ago, 19-Dec-98, to lugnet.robotics.handyboard)
|
| |
 | | Re: Question for you Technic pros
|
|
Hi: (...) The cross axle w/ eyes (Lego's name, not mine!) was in only 1 technic set, the small front end loader 8235 (1995). It differs from the two tie rods in that the tie rods can accept a ball joint but the axle w/ eyes cannot. The cross axle (...) (28 years ago, 19-Dec-98, to lugnet.robotics)
|
| |
 | | Re: flexible tubbing
|
|
(...) Hello... Your logging machine sounds like a great model. I hope you're able to show a bunch of detailed pictures in the future. <ICS> (28 years ago, 18-Dec-98, to lugnet.robotics)
|
| |
 | | Re: Question for you Technic pros
|
|
Linc Smith wrote in message ... (...) that (...) I'm not quite sure to which part you are refering at the above site, unless you are talking about the "rack w/ tie rods" which is still quite different from the cross axle w/ eyes #16. But now that I (...) (28 years ago, 18-Dec-98, to lugnet.robotics)
|
| |
 | | RE: urgent request help !!!!
|
|
-----Original Message----- From: phillip chia [mailto:philchia@sin...et.com.sg] Sent: Friday, December 18, 1998 7:04 AM To: handybd Cc: Mr Peter Lim Subject: urgent request help !!!! Hi Fred and others, I very desperate to debug the problem that (...) (28 years ago, 18-Dec-98, to lugnet.robotics.handyboard)
|
| |
 | | Re: Question for you Technic pros
|
|
John, if I am thinking of the same piece (cross axle w/ eyes #16, 1995) that can be found at (URL) I am aware of at least two very similar piece that is 6 studs (fairly sure) long. They are meant to accept a ball to form a ball-joint. Check out (URL) (28 years ago, 18-Dec-98, to lugnet.robotics)
|
| |
 | | Vertical Mill
|
|
I have posted pictures and a QuickTime movie of my new vertical mill at (URL) Bob Fay rfay@we.mediaone.net (28 years ago, 18-Dec-98, to lugnet.robotics)
|
| |
 | | RE: All-around-the-robot bump detection
|
|
Or you could begin to take a series of actions. If an action results in another hit on the bumper (or a continuous hit) then you abandon that action. So the robot tries everything until something works. That's just like evolution. :) -----Original (...) (28 years ago, 18-Dec-98, to lugnet.robotics)
|
| |
 | | Question for you Technic pros
|
|
Does the "Cross axle with holes" exist in any lengths other than 16? If so, in what lengths does it exist, and if possible what are the part numbers of the other lengths? -John Van (28 years ago, 18-Dec-98, to lugnet.robotics)
|
| |
 | | Re: All-around-the-robot bump detection
|
|
(...) What if something hits the robot? (28 years ago, 18-Dec-98, to lugnet.robotics)
|
| |
 | | dc motor output control
|
|
hi everyone, i need some help on controling the output voltage of the dc motor ports. the output voltage is 9.6V and i like to know if there is any way to clamp down the voltage to 5V or lesser. i try using a enternal resistor but the output signal (...) (28 years ago, 18-Dec-98, to lugnet.robotics.handyboard)
|