To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / *6621 (-20)
  Vertical Mill
 
I have posted pictures and a QuickTime movie of my new vertical mill at (URL) Bob Fay rfay@we.mediaone.net (28 years ago, 18-Dec-98, to lugnet.robotics)
 
  RE: All-around-the-robot bump detection
 
Or you could begin to take a series of actions. If an action results in another hit on the bumper (or a continuous hit) then you abandon that action. So the robot tries everything until something works. That's just like evolution. :) -----Original (...) (28 years ago, 18-Dec-98, to lugnet.robotics)
 
  Question for you Technic pros
 
Does the "Cross axle with holes" exist in any lengths other than 16? If so, in what lengths does it exist, and if possible what are the part numbers of the other lengths? -John Van (28 years ago, 18-Dec-98, to lugnet.robotics)
 
  Re: All-around-the-robot bump detection
 
(...) What if something hits the robot? (28 years ago, 18-Dec-98, to lugnet.robotics)
 
  dc motor output control
 
hi everyone, i need some help on controling the output voltage of the dc motor ports. the output voltage is 9.6V and i like to know if there is any way to clamp down the voltage to 5V or lesser. i try using a enternal resistor but the output signal (...) (28 years ago, 18-Dec-98, to lugnet.robotics.handyboard)
 
  Re: Limited number of MindStorms??
 
Just got my kit this morning from Lego Direct :))) One thing worth noting: Fear Airborne Express. Their driver deliverd all the packages for my apartments this morning... by leaving them on the sidewalk in front of the building. My Lego kit had a (...) (28 years ago, 18-Dec-98, to lugnet.robotics)
 
  Re: flexible tubbing
 
Thanks for the response. There are some good ideas here. I think that I will start by looking for some thin wall surgical tubing, and looking into gum rubber and silicon tubing. There is a RC model store on my way home, and I think I may be able to (...) (28 years ago, 18-Dec-98, to lugnet.robotics)
 
  Re: flexible tubbing
 
Try vacuum tubes at autoparts stores. I was at a Part America yesterday and they had a large variety of vacuum tubes that varied in flexibility. David (28 years ago, 18-Dec-98, to lugnet.robotics)
 
  Re: All-around-the-robot bump detection
 
lego-robotics@crynwr.com wrote in message I think this "bladder" idea might work better as you could have more air displaced (assuming you hit the obstacle with any kind of speed <G> ). Concern for a bump producing enough displacement to move the (...) (28 years ago, 18-Dec-98, to lugnet.robotics)
 
  Re: Limited number of MindStorms??
 
(...) What's your number? (URL) (...) Jim West NIC Architect MCI Worldcom (28 years ago, 18-Dec-98, to lugnet.robotics)
 
  Re: Limited number of MindStorms??
 
We'll they're over 86,000 now my RCX# is above that :) Jeff D. Payne UtahLINK Network Operations (...) (28 years ago, 18-Dec-98, to lugnet.robotics)
 
  Conductive Foam
 
Has anyone come up with any sensors using the conductive foam used in packing IC Chips. Years ago I saw a couple books on home-brew robotics and they were using this foam as a pressure sensor. Pass a current through the foam and the resistance (...) (28 years ago, 18-Dec-98, to lugnet.robotics)
 
  RE: All-around-the-robot bump detection
 
Why not set a variable with 1 or 0, e.g. 1=Forward, 0=Backwards. This way when the robot hits something you would know what direction it's traveling in. I haven't tried this, it's just an idea. -----Original Message----- From: Fred Read (...) (28 years ago, 18-Dec-98, to lugnet.robotics)
 
  Re: All-around-the-robot bump detection
 
How 'bout this as an alternative. A flexable containment, possibly the moderate diameter rubber tube, inside which are two circuits. One is a continuous metal strip which runs along the inside edge of the outside wall of the tube. The second is a (...) (28 years ago, 18-Dec-98, to lugnet.robotics)
 
  RE: All-around-the-robot bump detection
 
Jeremy makes a very good point ! :) You should be able to get away with 3 (in theory). I think this "bladder" idea might work better as you could have more air displaced (assuming you hit the obstacle with any kind of speed <G> ). me Andrew Phelps (...) (28 years ago, 18-Dec-98, to lugnet.robotics)
 
  RE: All-around-the-robot bump detection
 
If you have three sections and overlap them correctly, you can distinguish six different directions of contact. You wouldn't have to multiplex the touch sensors if you didn't need any more inputs, but you could multiplex them onto one input if you (...) (28 years ago, 18-Dec-98, to lugnet.robotics)
 
  RE: All-around-the-robot bump detection
 
Hmmmmm, It's morning and I haven't had coffee yet so bear this in mind but it seems to me that this is a) a fairly cool scheme for post collision detection, and b)expandable to support direction detection through the use of 4 sensors. Imagine that (...) (28 years ago, 18-Dec-98, to lugnet.robotics)
 
  Re: All-around-the-robot bump detection
 
(...) I haven't actually tried this, but I can hardly imagine that the pressure generated from just squeezing one small part of the tube is sufficient to extend a cylinder and press a touch sensor. The pressure generated will probably just "vanish" (...) (28 years ago, 18-Dec-98, to lugnet.robotics)
 
  RE: All-around-the-robot bump detection
 
Oh yeah, that too. :) Jeremy Morton a-jeremm@microsoft.com -----Original Message----- From: Fred Read [mailto:fred@corp.ne...om.net.uk] Sent: Friday, December 18, 1998 6:10 AM To: lego-robotics@crynwr.com Subject: Re: All-around-the-robot bump (...) (28 years ago, 18-Dec-98, to lugnet.robotics)
 
  RE: All-around-the-robot bump detection
 
The tubing is such a small diameter that I think it would take a large surface of contact for enough air to be displaced to move a pneumatic cylinder. Maybe with not-Lego(tm) tubing that was, maybe 1/4 to 1/2 inch [6.35 to 12.7 mm :P ] in radius (...) (28 years ago, 18-Dec-98, to lugnet.robotics)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR