 | | Re: Sensor information & Extreme Creatures
|
|
In article <F437wI.MyC@lugnet.com>, Michael Gasperi <lugnet.robotics@lugnet.com> writes (...) If you mounted a fast-response thermistor behind a lens you would have a very directional scanning heatseeker. Obviously you would need to rotate the (...) (28 years ago, 17-Dec-98, to lugnet.robotics)
|
| |
 | | Re: Sensor information & Extreme Creatures
|
|
In article <36783E8B.7C3D@virgin.net>, Barry Bott <barry.bott@virgin.net> writes (...) Coins on the floor are no problem. What we need is a robot which finds coins down the side of the settee. (28 years ago, 17-Dec-98, to lugnet.robotics)
|
| |
 | | Re: New ROBOLAB pages... (Macs to IR tower)
|
|
On 12/16/98 3:51 PM, John Donaldson, jdonaldson@ghg.net, said: (...) Ok, I haven't actually tried this, but from what I've gleaned from the messages here: 1) The Mindstorms software will NOT work under Mac emulation because of the archaic and (...) (28 years ago, 17-Dec-98, to lugnet.robotics)
|
| |
 | | Re: New ROBOLAB pages....
|
|
In a message dated 12/16/98 10:53:55 PM Eastern Standard Time, jdonaldson@ghg.net writes: << Question??? If Robolab uses the RCX and can be programmed from either a PC or a MAC, How does it download the program on a MAC?? From what I have been (...) (28 years ago, 17-Dec-98, to lugnet.robotics)
|
| |
 | | Re: New ROBOLAB pages....
|
|
Question??? If Robolab uses the RCX and can be programmed from either a PC or a MAC, How does it download the program on a MAC?? From what I have been reading, the IR tower CAN NOT be used on a MAC. John A. Donaldson (...) (28 years ago, 16-Dec-98, to lugnet.robotics)
|
| |
 | | Re: NQC software for Mac? (Robolab back ordered)
|
|
Chris, If it is just having RTS=CTS, a software solution may be possible. E.g.: patch the SPIRIT.OCX so that it always returns RTS=CTS, patch the Mindstorm so that it doesn't care if the tower is connected, or patch windows or DOS so that RTS=CTS. (...) (28 years ago, 17-Dec-98, to lugnet.robotics)
|
| |
 | | Re: NQC software for Mac? (Robolab back ordered)
|
|
There are USB to Serial port adapters. Don't know if they work with a MAC or IMAC, but they are real. John A. Donaldson (...) (28 years ago, 16-Dec-98, to lugnet.robotics)
|
| |
 | | RE: Batteries?
|
|
(...) Sorry, I have no experience with rechargables in the RCX. (...) "9-12 volts" applies to the external power jack, and is for AC. That is not the same as the battery voltage. (...) No, it's not below range at all. The Mindstorms manual clearly (...) (28 years ago, 17-Dec-98, to lugnet.robotics)
|
| |
 | | Re: Archives?
|
|
Ramsey Jr, William T writes: > I just joined this list. Is there somewhere or some way to look at archives > from the list? Yes, unfortunately it's terribly clumsy. Send mail to lego-robotics-help for instructions. I'm working on fixing it.... (28 years ago, 17-Dec-98, to lugnet.robotics)
|
| |
 | | Re: Sensor information & Extreme Creatures
|
|
Barry Bott wrote in message <36783E8B.7C3D@virgin.net>... (...) I agree that I'm asking a lot out of a humble thermistor. My plan is to have a two thermistors. One on each end of a fairly long pole mounted like headlights on a mobile robot. Just (...) (28 years ago, 17-Dec-98, to lugnet.robotics)
|
| |
 | | Re: Batteries?
|
|
(...) The RCX uses a six-pack of AA batteries. Its voltage range is 9-12 volts, which puts the onboard power with alkies at the lower end. A six-pack of nicads or nimhs puts out about 7.2 volts, possibly enough to work but definitely below range. It (...) (28 years ago, 17-Dec-98, to lugnet.robotics)
|
| |
 | | Re: NQC software for Mac? (Robolab back ordered)
|
|
(...) Err, right. And if there's DTR/DCD printed on the wires it just won't play. Naughty people messing about with the assigned meanings of the pins. Whatever next? Cheers, Ben. (28 years ago, 17-Dec-98, to lugnet.robotics)
|
| |
 | | Re: flexible tubbing
|
|
How about rubber/latex surgical tubing from a chemical or medical supply house? If none in your locale, consider McMaster-Carr in LA -- many varieties of tubing (www.mcmaster.com -- no minimum order). Al Thiele (...) (28 years ago, 17-Dec-98, to lugnet.robotics)
|
| |
 | | Re: Sensor information & Extreme Creatures
|
|
(...) site: (...) I don't think any sensor using a thermistor will be really succesfull, probably the best technique is to use a pyroelectric sensor, Maplin in England sell them, Radio Shack in the States must. The pyroelectric sensor is an IR (...) (28 years ago, 16-Dec-98, to lugnet.robotics)
|
| |
 | | Re: NQC software for Mac? (Robolab back ordered)
|
|
I seem to remember seeing an add-in board which would add PC style serial ports to Macs. Now this was several years ago; it was for the NuBus; and it was rather expensive. I believe it was done so you could interface lab equipment to Macs. It may (...) (28 years ago, 17-Dec-98, to lugnet.robotics)
|
| |
 | | Re: NQC software for Mac? (Robolab back ordered)
|
|
(...) DTR/CD aren't alternatives, they serve an entirely different purpose. The PC software toggles the CTS signal, which the tower shorts to RTS, so that it can tell if the tower is connected. Since the Mac serial port doesn't have those pins, (...) (28 years ago, 17-Dec-98, to lugnet.robotics)
|
| |
 | | Warning: No CyberMaster in Macs
|
|
I've been reading some posts regarding Mac problems and I noticed that no one ever referred to CyberMaster problems in Mac (which is a good thing). Unfortunately people with Macs are _destined_ to not be able to use their CyberMaster, since it's not (...) (28 years ago, 16-Dec-98, to lugnet.robotics)
|
| |
 | | Batteries?
|
|
Hello All, Is there a rechargable batteries that anyone can suggest to use with the RCX? How long does a group of batteries usually last? What happens to the programs stored in the RCX when the batteries rundown? (28 years ago, 16-Dec-98, to lugnet.robotics)
|
| |
 | | RE: NQC software for Mac? (Robolab back ordered)
|
|
It's been a long time since I worked with serial hardware, but isn't there an alternative pair of pins to RTS/CTS? DTR/DTS or something like that? If the Mac sets the other pins you might be able to short them to the RTS/CTS pins. I know I've done (...) (28 years ago, 16-Dec-98, to lugnet.robotics)
|
| |
 | | Re: NQC software for Mac? (Robolab back ordered)
|
|
(...) It will *never* work. The PC software fiddles with the RTS and CTS pins, which the Mac *does not have*. --- Chris Osborn FozzTexx Enterprises 707 226 7629 - Voice 2136 Coronado Ave. 707 253 3063 - Fax Napa, CA 94559 <fozztexx@fozztexx.com> (...) (28 years ago, 16-Dec-98, to lugnet.robotics)
|