 | | RE: gear differential
|
|
Is the Lego differential piece that big gray frame that looks like some gears ought to go in it? If so, how do you build it? (28 years ago, 18-Nov-98, to lugnet.robotics)
|
| |
 | | Re: Direct control of IRDA
|
|
(...) Well, I read all that and I'm still none the wiser, has anyone talked to an RCX using a Windows PC's IrDA ? Matt (28 years ago, 18-Nov-98, to lugnet.robotics)
|
| |
 | | Re: Miniboard/download mode
|
|
(...) Check the voltage at the MOBD pin on the chip (not the socket, not the bottom of the board). If it is 5V with the switch in the one position, and ground (0V) in the other position, you may have a defective chip. Otherwise I'd guess open (...) (28 years ago, 18-Nov-98, to lugnet.robotics.handyboard)
|
| |
 | | RE: Direct control of IRDA
|
|
I don't think you can do it. They use different carrier frequencies, and slightly different signal timing. If you could get low-level control of the infrared transciever, you might be able to do it - but I'm guessing most PC IrDA ports are hardwired (...) (28 years ago, 18-Nov-98, to lugnet.robotics)
|
| |
 | | Botcode and NT 4.0
|
|
I downloaded and successfully installed Botcode under Windows NT 4.0, and after moving my IR Tower from Win95 to the NT box, it was a simple menu click to select the COM port and send instructions to the RCX - - great work, Marty!! Now on to (...) (28 years ago, 19-Nov-98, to lugnet.robotics)
|
| |
 | | Technic Idea Book
|
|
Where can One find the 'Lego Technic Idea Book'? Thanks in advance, Ken (28 years ago, 19-Nov-98, to lugnet.robotics)
|
| |
 | | Re: Technic Idea Book
|
|
(...) Well, all of the Technic idea books are out of print and unavailable from shop-at-home. There are 4 different ones: 8891 - (1991) I see occasionally in auctions on rec.toys.lego 8890 - (1998) also seen occasionally on rtl auctions 8889 - (...) (28 years ago, 19-Nov-98, to lugnet.robotics)
|
| |
 | | Re: motor port problem .
|
|
hi, I have a big problem. I followed the method of yours that just lift up pin 8 of one L293 and wirewrapped it. The positive supply is wirewrapped to pin 8 . How about the negative supply of the batteries should insert or wirewrapped? I inserted (...) (28 years ago, 19-Nov-98, to lugnet.robotics.handyboard)
|
| |
 | | Re: motor port problem .
|
|
hi , Attached from the previous mail, I have already solved the problem listed below. It is the 7404 is damaged .What causes it? Any ideas? RIght now this problem that melted my socket on the L293, the supply I used is 12V supply to my 2 DC motors. (...) (28 years ago, 19-Nov-98, to lugnet.robotics.handyboard)
|
| |
 | | Re: gear differential
|
|
(...) Hey, I had a worse idea once. Actually I'm still proud of it - I built an all-LEGO automatic transmission. Only *how* it worked was by using pairs of the little crown bushings (seemingly defunct as of this year?) as clutches, a pair at each (...) (28 years ago, 19-Nov-98, to lugnet.robotics)
|
| |
 | | Re: nqc-mode.el, very simple Emacs major-mode for NQC
|
|
(...) Go dude. Emacs rules. This is way cool (I have emacs on my NT box) (...) What, you didn't comment it yourself? :-) (28 years ago, 19-Nov-98, to lugnet.robotics)
|
| |
 | | Re: Technic Idea Book
|
|
John Cromer <lego-robotics@crynwr.com> wrote in message 199811190144.RAA1099...ech.edu... (...) In addition, I believe that Busy Bee still carries this (I got one from them a few months ago). (28 years ago, 19-Nov-98, to lugnet.robotics)
|
| |
 | | Re: Direct control of IRDA
|
|
(...) Short answer -- the IR protocol used by the RCX is more akin to that used in TV remotes than it is to the IrDA standard. If you could talk to your IR port directly, you could probably do that. But mostly, the low-level functionality is hidden (...) (28 years ago, 19-Nov-98, to lugnet.robotics)
|
| |
 | | Re: gear differential
|
|
(...) If you mean the cylindrical thing with a sorta gear-like thing at each end and a sorta peg in the middle, yes, that's it. I think the Mindstorms constructowhatever book has instructions... (28 years ago, 19-Nov-98, to lugnet.robotics)
|
| |
 | | Re: Other batteries...
|
|
A gell cell battery is charged via a maximum allowed charging voltage. If the charger doesn't limit the charging voltage to less than 14 volts it will shorten the life of a 12v gell cell considerably. A Ni-Cad uses a constant charging current, but (...) (28 years ago, 19-Nov-98, to lugnet.robotics.handyboard)
|
| |
 | | Help
|
|
Hallo All , i have a big problem, i want to use the ports Y0-Y5 but i don´t know why. I need a ports for write and read. On Saturday i have my first sumo-robot contest and i need this ports !!!! I´m want to use a Sharp GP2D02 Distance Sensor, for (...) (28 years ago, 19-Nov-98, to lugnet.robotics.handyboard)
|
| |
 | | Help Y0-Y5
|
|
Sorry for my bad english ! i want to write - i have a big problem, i want to use the ports Y0-Y5 but i don´t know how i use them. Bernd Klein (28 years ago, 19-Nov-98, to lugnet.robotics.handyboard)
|
| |
 | | Re: gear differential
|
|
(...) For those who still don't know how the LEGO differential works, take a look at: (URL) (28 years ago, 19-Nov-98, to lugnet.robotics)
|
| |
 | | Re: gear differential
|
|
In article <3653850B.99A94081@acm.org>, stephen p spackman <stephen@acm.org> writes (...) Indeed. Lego themselves double up sometimes by adding extra pair of pulleys - that helps a lot. Is there a part no for rubber band spares - on their own. The (...) (28 years ago, 19-Nov-98, to lugnet.robotics)
|
| |
 | | Re: Direct control of IRDA
|
|
In article <slrn75745o.9uh.matt...a.bu.edu>, Matthew Miller <lugnet.robotics@lugnet.com> writes (...) He he - how about using a digital watch then - the ones that can 'learn' TV operation. Now having said that flippantly, now 'we' are able to write (...) (28 years ago, 19-Nov-98, to lugnet.robotics)
|