To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / *42919 (-20)
  Rotating through a four-bit nibble
 
No, it's not pornographic (look over in rtlToronto - I hear it's a fun thread). But I'm working in NQC, and I need to rotate the bit series in a 4-bit (or 8-bit) nibble embedded in a 16-bit word. Annoying. Any suggestions? Masking the desired four (...) (21 years ago, 20-Sep-05, to lugnet.robotics)
 
  NWBrickCon™ 2005 Technic Award Sneak Peek
 
NWBrickCon is almost here. This is just a last little push for anyone bringing Technic MOCs. If you are bringing anything in the Technic theme please email me and let me know what you are bringing and how much table space you will need. ... and now (...) (21 years ago, 20-Sep-05, to lugnet.events.nwbrickcon, lugnet.events, lugnet.announce, lugnet.technic, lugnet.robotics, FTX) !! 
 
  position servoing under BrickOS
 
Thanks to your advices, Dick, Matt, and Steve, I've been very happy to solve my time sampling problems, installing BrickOS, which runs the rcx fast enough to get a proper position servoing (using rotation or light sensor, and a PID controller). I (...) (21 years ago, 20-Sep-05, to lugnet.robotics.rcx)
 
  error in using brickOS under Bricx Command Center
 
Dear all, I am new to Lego Mindstorms programming. Recently I installed Bricx Command Center in Windows XP Home following the instructions in (URL) I am able to use NQC and leJOS but not brickOS under Bricx Command Center. (Downloading the brickOS (...) (21 years ago, 17-Sep-05, to lugnet.robotics.rcx.legos)
 
  Re: Legway
 
(...) Yes, one of the most popular robots I've made, when it's working well, just stands there... :) (...) That's fine with me. However, don't be too surprised if it DOESN'T attract a big crowd. It's a big attraction to people who understand what it (...) (21 years ago, 19-Sep-05, to lugnet.robotics)
 
  Re: Legway
 
Hello, (...) I made a Legway too this weekend (i ordered some sensors to hitechnic). I didn't see it in real life before. It is really funny to see this robot standing up on only 2 wheels. if you're ok for this, Steve, i will show it at LEGOWorld (i (...) (21 years ago, 19-Sep-05, to lugnet.robotics)
 
  Re: time sampling under the rcx standard OS
 
(...) Well, in BrickOS, my loops usually execute at > 1kHz, so I usually just set it to check the sensor, and set the motor every 1ms. So it just keeps checking the clock. (...) Yes. There's an option that lets you download an "SREC" type of file. I (...) (21 years ago, 19-Sep-05, to lugnet.robotics.rcx.nqc)
 
  Re: time sampling under the rcx standard OS
 
(...) Sorry, I didn't explain. This program only aims at checking the loop frequency capability of the rcx firmware, implementing a PWM. The rotation sensor is only used as a potentiometer knob, allowing me to determine by hand the PWM pulse as (...) (21 years ago, 19-Sep-05, to lugnet.robotics.rcx.nqc)
 
  Re: time sampling under the rcx standard OS
 
Thank you Matt, the RCX loops much faster with your advices : about 10 loops per second. But as this frequency depends on the calculations included in the loop, I’m afraid this will not be enough. So I tried to download (URL) but it just appears as (...) (21 years ago, 18-Sep-05, to lugnet.robotics.rcx.nqc)
 
  Re: time sampling under the rcx standard OS
 
Thank you Dick, for advicing me to switch to the faster firmware, I’m sure I need both a 1-millisecond basic clock, and the 128 power level capability. So I tried to download it from (URL) but it just appears as a text file, which I don’t know how (...) (21 years ago, 18-Sep-05, to lugnet.robotics.rcx.nqc)
 
  Re: 5-DOF arm
 
(...) I would like to see some pictures. Thanks, Kev (21 years ago, 17-Sep-05, to lugnet.robotics)
 
  RE: time sampling under the rcx standard OS
 
Here are some comments on how to improve your code for real-time performance. 1. Move the "SetUserDisplay" out of the loop and put it just before the loop. 2. I think the "OnFwd" macro is actually two instructions: "Fwd" and then "On". Replace this (...) (21 years ago, 17-Sep-05, to lugnet.robotics.rcx.nqc)
 
  Re: time sampling under the rcx standard OS
 
(...) From what I've seen, the standard firmware takes about 3ms per command, and the same program will run on BrickOS about 100 times faster. I usually set up my BrickOS programs so they use the internal timer, and only update the motor setting (...) (21 years ago, 17-Sep-05, to lugnet.robotics.rcx.nqc)
 
  Re: time sampling under the rcx standard OS
 
(...) Francois, I think you should be able to get much faster sampling. I can easily get 10-20 Hz, and others have claimed to get down to 3 ms. Whether it can be done at a constant rate, I'm not sure, and think it probably depends on what else is in (...) (21 years ago, 17-Sep-05, to lugnet.robotics.rcx.nqc)
 
  time sampling under the rcx standard OS
 
Hi list, I'm trying to implement a position regulation (using a motor and a rotation sensor), using for instance a PID (Proportional-Integr...erivative) regulation. I tried to code it in NQC, using the standard OS, but it seems that the RCX loops at (...) (21 years ago, 17-Sep-05, to lugnet.robotics.rcx.nqc)
 
  time control : BrickOS versus the RCX standard OS ?
 
Hi list, I'm trying to implement a position regulation (using a motor and a rotation sensor), using for instance a PID (Proportional-Integr...erivative) regulation. I tried to code it in NQC, using the standard OS, but it seems that the RCX standard (...) (21 years ago, 17-Sep-05, to lugnet.robotics.rcx.legos)
 
  5-DOF arm
 
Hi everyone -- I have recently completed my Nth version of a 5-DOF arm plus claw. Finally, I am guardedly happy with the result. I think it's about as minimalist as such a thing can be; it's much smaller than models with similar capability I've seen (...) (21 years ago, 17-Sep-05, to lugnet.robotics)
 
  IR-based proximity measurement
 
I'm changing the subject line in the middle of the thread. Wonder what the server will do with that... I tried out Brian's "Max-picking" ping method, as well as a few other things. Here's a summary of what I found: 1) If the active sensor readings (...) (21 years ago, 16-Sep-05, to lugnet.robotics.rcx.nqc)
 
  Re: direct manipulation of bits in RCX registers using NQC
 
(...) Correct. A NQC command (say, "Wait(10);") is converted to one or more "bytecodes" (in this case, one bytecode, namely a string of 4 bytes (0x43 0x02 0x0a 0x00), the first of which is a command (0x43) while the following three are information (...) (21 years ago, 16-Sep-05, to lugnet.robotics.rcx.nqc)
 
  Re: direct manipulation of bits in RCX registers using NQC
 
Hey, Thanks for all the helpful responses, everyone. Brian: (...) I guess that "firmware" must be the code that tells RCX how to interpret user instructions (NQC, C, IC, opcodes, or whatever), and convert them to binary machine-specific code. Right? (...) (21 years ago, 16-Sep-05, to lugnet.robotics.rcx.nqc)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR