To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / *40984 (-20)
  Re: Help installing brickOS
 
(...) Sure. The configure script tries to find the gcc cross compiler toolchain for the brick's hitachi processor. This chain is needed to compile brickOS to a program that can be run by the RCX. But it seems that you did not install the tool chain. (...) (22 years ago, 28-Oct-04, to lugnet.robotics.rcx.legos)
 
  BricxCC 'Float' Command not working on Scout
 
While programming a Scout using BrickCC, no matter how many times I tried, I could not get the Scout to 'float' its motors. The program was as follows- task main() { OnFwd(OUT_A); Wait(50); Float(OUT_A); } After a half second the motor would brake, (...) (22 years ago, 28-Oct-04, to lugnet.robotics)
 
  Re: Help installing brickOS
 
(...) I believe that I had the exact same problem a few weeks ago, but I found that using a pre-built package takes a lot of the hassle out of installing BrickOS. The pre-built packages can be found at: (URL) hope this helps, Timothy (22 years ago, 27-Oct-04, to lugnet.robotics.rcx.legos)
 
  Help installing brickOS
 
I'm trying to install brickOS 0.2.6.10.6 on WIN NT. After unning "configure" it's busy for along time, and terminates with the message -"No Hitachi gcc compiler found. Please install compiler and try again." Any suggestions? Thanks, Jordon (22 years ago, 27-Oct-04, to lugnet.robotics.rcx.legos)
 
  GASTON
 
Hi all, 1. Finally most of the documents, building instructions, schematics and so on are available concerning our robot GASTON (URL) Ultimate Robolab is advancing well and will soon be available for beta-testing: (URL) (22 years ago, 27-Oct-04, to lugnet.robotics)
 
  Re: Compound shaft
 
(...) You could use a differential - or maybe a large turntable. ---...--- Steve Baker ---...--- HomeEmail: <sjbaker1@airmail.net> WorkEmail: <sjbaker@link.com> HomePage : (URL) : (4 URLs) GEEK CODE BLOCK----- GCS d-- s:+ a+ C++++$ UL+++$ P--- (...) (22 years ago, 27-Oct-04, to lugnet.robotics)
 
  Re: Piggybacking sensors, but in a different way
 
(...) While you may be able to connect a touch sensor (passive) to two RCXs, I doubt that would work with a light sensor (any active sensor). Mainly, because one of them must be set to power the sensor. Normally, when the sensor is read by an RCX, (...) (22 years ago, 26-Oct-04, to lugnet.robotics.rcx)
 
  Re: 1Wire vs I2C
 
On Tue, 26 Oct 2004 18:19:36 GMT, Bruce Boyes <lego-robotics@crynwr.com> wrote: Big Snip! (...) Whew! Thanks for the insight! How does the component/driver cost compare? -Rob. (22 years ago, 26-Oct-04, to lugnet.robotics)
 
  1Wire vs I2C
 
(...) I2C is much faster (100 Kbit I2C is the slowest, vs 14 Kbit 1Wire), more reliable, but much shorter distance. Newer I2C can be 1 Mbit or more. (...) 1Wire will never do 115 kbits reliably. The 1Wire overdrive option is not reliable and few (...) (22 years ago, 26-Oct-04, to lugnet.robotics)
 
  Re: Compound shaft
 
(...) An example of this is here: (URL) using (URL) that can engage with any of the technic 1x plates : 2719 Technic Plate 1 x 10 with Holes 4263 Technic Plate 1 x 4 with Holes 4262 Technic Plate 1 x 6 with Holes 4442 Technic Plate 1 x 8 with Holes (...) (22 years ago, 26-Oct-04, to lugnet.robotics)
 
  Piggybacking sensors, but in a different way
 
Is it possible to piggyback 1 sensor onto two rcx's? For instance, have one light sensor connected to port 1 of two different rcx's at the same time. The purpose would be for one rcx to control chassis movement, and another to control manipulator (...) (22 years ago, 26-Oct-04, to lugnet.robotics.rcx)
 
  Re: Compound shaft
 
(...) I've seen this done a) with a new style differential - it will spin free on a central axle and has a 24t gear at one end and a 16t at the other. b) two 16t "clutch" gears connected either via the toothed bearings, or via the driving ring (...) (22 years ago, 26-Oct-04, to lugnet.robotics)
 
  Compound shaft
 
Does anyone know of a compound shaft in Lego shafts? The primary purpose would be for a clock (minute and second hands) Thanks! Larry (22 years ago, 26-Oct-04, to lugnet.robotics)
 
  Re: Mini-RCX
 
(...) The pcb for my Brainibot kit is around that size. (Just search the web for "Brainibot".) It uses an 8-pin PIC and has two H-bridge motor drivers, two "antennae" (e.g. push switches), a light sensor and a sounder. One of the models is (...) (22 years ago, 26-Oct-04, to lugnet.robotics)
 
  Re: Mini-RCX
 
(...) Any idea on how I2C compares to 1-wire? I know that there 1-wire is being considered for some open-source home automation schemes because of the extremely low cost of interfacing, and the data rates seem comparable 115k for 1-wire vs. 100k for (...) (22 years ago, 26-Oct-04, to lugnet.robotics)
 
  Re: Mini-RCX
 
(...) I don't see a problem with the computer side of things - what concerns me is battery storage and power management. You can get *tiny* computers that would easily fit in this kind of tiny space - but the RCX motors need 9 volts - you would need (...) (22 years ago, 25-Oct-04, to lugnet.robotics)
 
  CMUCam2
 
Hi, recently I have read about the the CMUCam2. This is a quite cheap camera for robotics. This camera module contains also a µP module for image reconition tasks. Here are a list of the features: • Track user defined color blobs at up to 50 Frames (...) (22 years ago, 25-Oct-04, to lugnet.robotics)
 
  Re: Mini-RCX
 
(...) Yes, it is possible. Check this out: (URL) (22 years ago, 25-Oct-04, to lugnet.robotics)
 
  Re: Mini-RCX
 
(...) Oh, it's possible (if you put the batteries someplace else)... there's more smarts than an RCX in a high-end wristwatch, and that's a smaller footprint than you specify. The trick is that to do it, you'd have to build it from the chips up, (...) (22 years ago, 25-Oct-04, to lugnet.robotics)
 
  Re: Rotation sensor limitation
 
(...) The simplest answer is to try it. Yes the limit that an RCX 16 bit integer can hold is 32767. From there things go to -32768 down to zero I think. (...) Kevin (22 years ago, 25-Oct-04, to lugnet.robotics.rcx.nqc)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR