 | | Problems after upgrading from brickos 0.2.6.09 to 0.2.6.10
|
|
Hello, I hope somebody could help me with the following problem. So far I was using brickos 0.2.6.09 under Windows XP and everything worked fine. I downloaded version 0.2.6.10 and downloaded it's brickos.srec file to the RCX. As soon as I switch on (...) (24 years ago, 5-Apr-03, to lugnet.robotics.rcx.legos)
|
| |
 | | Re: baby walker
|
|
after watching that film, i got to say that this is fun but its totally not a walker. first foremost for that leg drag, I'd rename this Igor or somthing. -tk "Philippe Hurbain" <philohome@free.fr> wrote in message news:HCvtts.nF@lugnet.com... (...) (...) (24 years ago, 5-Apr-03, to lugnet.technic, lugnet.robotics)
|
| |
 | | Re: baby walker
|
|
...and then they were five... The 1x7 liftarm is a bit short and the motor bumps against the flexible axle. So I used a 1x9 (7+2) to be low enough, and I could remove Micromotor bottom. I used a 1x2 liftarm with plate only for aestetical reasons... (...) (24 years ago, 5-Apr-03, to lugnet.technic, lugnet.robotics)
|
| |
 | | Re: BrickOs Problem (again)
|
|
(...) Cygwin is pure Windows. DJGPP is DOS, and doesn't work well with brickOS. Although everyone should use Linux. DJGPP and brickOS: I managed to build binutils under djgpp, gcc failed but is probably fixable. However, djgpp doesn't have POSIX (...) (24 years ago, 5-Apr-03, to lugnet.robotics.rcx.legos)
|
| |
 | | Re: Lego motor reverse with 2 switches
|
|
You could make a half H-bridge: --------| i---...---| i---...--- | | | | | | / Motor / | | | ---...--- Remember that you have to program a dead time between the switches so as not to short the batteries. You could also make a full H-Bridge, using (...) (24 years ago, 5-Apr-03, to lugnet.robotics)
|
| |
 | | Re: baby walker
|
|
(...) Cool! I figured that the stiffness of the wire would help. I guess I'll call it Shorty ,as it's only a little over an inch tall :). Now I've just got to get that micro motor ordered so I can try it out myself. I'm wondering if you could try (...) (24 years ago, 5-Apr-03, to lugnet.technic, lugnet.robotics)
|
| |
 | | Re: baby walker
|
|
It works! (URL) stability is obtained more from wire stiffness than from 2x4 brick (not heavy enough, without wire motor would turn over when in topmost position) Cheers, Philo www.philohome.com (...) (24 years ago, 5-Apr-03, to lugnet.technic, lugnet.robotics)
|
| |
 | | Lego motor reverse with 2 switches
|
|
I built a lego robot, I am using linux as operating system. I also have a simple circuit connected to the printer port that has 4 switches. (I can activate or deactivate 4 circuits) . My robot has 2 motors, and i need to forward or reverse each of (...) (24 years ago, 5-Apr-03, to lugnet.robotics)
|
| |
 | | Re: BrickOs Problem (again)
|
|
(...) You didn't install tar. Run Cygwin setup again and add tar. (...) No, incorrect. (...) No, he needs to install tar. Max. (24 years ago, 5-Apr-03, to lugnet.robotics.rcx.legos)
|
| |
 | | Re: BrickOs Problem (again)
|
|
(...) Hello, I think it's really hard to install brickOS on XP cause Cygwin is on a dos base (no ?) and XP have no DOS (only emule). To solve you problem you should install linux :-P Seriously : if cygwin don't find tar you should try to search (...) (24 years ago, 5-Apr-03, to lugnet.robotics.rcx.legos)
|
| |
 | | BrickOs Problem (again)
|
|
Hi, Recently, I have tried and tried to install BrickOS into Win XP. However, I have had problems in installing. I have installed cygwin and checked that all files have been installed. Built the gcc 2.95.2 and binutils 2.10.1 cross compiler. But I (...) (24 years ago, 5-Apr-03, to lugnet.robotics.rcx.legos)
|
| |
 | | Re: synchro drive robot
|
|
I have a few synchro drive robots here: (URL) CAD, but some good shots are there. (...) (24 years ago, 5-Apr-03, to lugnet.robotics)
|
| |
 | | synchro drive robot
|
|
Hi, I'm trying to build a synchro drive robot and am having trouble with the gearing. I was wondering if anyone had a cad drawing of a synchro drive or pictures of the gearing of a synchro drive. Thanks Scott (24 years ago, 5-Apr-03, to lugnet.robotics)
|
| |
 | | Re: ....powered caster.....
|
|
(...) You may get some ideas from my page here: (URL) first design shown is what you are after: a powered caster. Its probably bigger than what you want though. The other one is an offset wheel design that would only work with a synchro robot. I (...) (24 years ago, 4-Apr-03, to lugnet.robotics)
|
| |
 | | Re: Spybotics Comms
|
|
In lugnet.robotics.spybotics, Marco Correia writes: [snip] (...) I need help answering the question "Can a Spybot send Mana IR-like protocol? I want my Spybot to control my mana. I'm too stupid to interpret to Spybot SDK on my own, and there's no (...) (24 years ago, 4-Apr-03, to lugnet.robotics.spybotics, lugnet.robotics.rcx.nqc, lugnet.robotics)
|
| |
 | | Sensor Assembly Problem
|
|
Hi, I'm using the handyboard for a robotics competition, and I have been having a problem when I use my compass and sonar together. I am using a Daventech SRF04 ultrasonic ranger, and a Daventech compass. Here is the problem: I can read the sonar (...) (24 years ago, 4-Apr-03, to lugnet.robotics.handyboard)
|
| |
 | | RE: sensors, actuators, and software, oh my!
|
|
(...) hmmmm... these jump to mind: Human "sensors": a) global/positional(2D) Light Level (also 3D because we move our head/eyes taking notice of the sampling vector) b) global/positional(stereo) Sound Frequency/Level (might also be considered 3D (...) (24 years ago, 4-Apr-03, to lugnet.robotics)
|
| |
 | | ....powered caster.....
|
|
Hi All, I am working on designing a powered caster wheel.......that is a caster wheel that has an integral Lego motor, and wheel/tire. I am looking to make it as compact as possible. I am using one of the 9 volt gear motors. I have tried having the (...) (24 years ago, 4-Apr-03, to lugnet.robotics)
|
| |
 | | Re: diet walker
|
|
"travis" <phree@attbi.com> wrote in message news:HCt81I.160H@lugnet.com... (...) (URL) (24 years ago, 4-Apr-03, to lugnet.robotics, lugnet.technic)
|
| |
 | | diet walker
|
|
I don't know where I'll shave the next part, but here is the Diet Walker. It walks and is very sturdy due to the elastic band being replaced by gears. The feet do work, and are much more sturdy than I thought they might be. (URL) me know what you (...) (24 years ago, 4-Apr-03, to lugnet.announce.moc, lugnet.build.mecha, lugnet.robotics, lugnet.technic)
|