 | | Re: Firmware download troubles
|
|
(...) ... (...) Dick and others, Thanks - this helped. What I did to solve this was run the NCQ command-line download at "normal" speed. This worked the first time. Interestingly, I am not sure that the Bricx (v3.3) download was running quad speed (...) (23 years ago, 10-Dec-02, to lugnet.robotics.rcx)
|
| |
| | Re: Firmware download troubles
|
|
A likely explanation for your downloading problem is the following. Standard Lego software uses 2400 baud data rate and a protocol that sends "double" bytes. The "double" byte is that each data byte is followed by its complement. Alternative (...) (23 years ago, 10-Dec-02, to lugnet.robotics.rcx)
|
| |
| | Re: want to get inentors kit but...
|
|
(...) If you want to use the 'official' Lego software, then I'm not sure what Windoze OS's are supported - but certainly Linux isn't. However, many (most even?) serious users end up using a 3rd party software package called 'Not Quite C' (NQC) which (...) (23 years ago, 10-Dec-02, to lugnet.robotics)
|
| |
| | RE: Installation Help!
|
|
Max, Aha! I did that and it got a lot further this time, but still failed. I'll have to wade through the log file to try and pinpoint where it went wrong as I don't want to post the whole 180k. Thanks for your help! Andy -----Original Message----- (...) (23 years ago, 10-Dec-02, to lugnet.robotics.rcx.legos)
|
| |
| | Re: Firmware download troubles
|
|
Matt, I discovered that the IR LED's and detector on my serial tower was located higher than I expected and pointed upward somewhat. I was able to get better transfers when the tower was leaning forward (pointing downward so to speak). Otherwise, I (...) (23 years ago, 9-Dec-02, to lugnet.robotics.rcx)
|
| |
| | Re: Firmware download troubles
|
|
Also: When it seems to get to the very end before the error appears, I sometimes get a long (3-4 seconds) low tone from the RCX. Matt (23 years ago, 9-Dec-02, to lugnet.robotics.rcx)
|
| |
| | Firmware download troubles
|
|
Hi All, I have pulled my RCX out of summer storage and I am trying to bring it to life. I have tried to download the 2.0 Firmware (firm0328.lgo) dozens of times with no success. It starts to download, then somewhere in the middle, or very close to (...) (23 years ago, 9-Dec-02, to lugnet.robotics.rcx)
|
| |
| | Re: Installation Help!
|
|
(...) You need to install the Cygwin gcc package. You need the normal Cygwin gcc to build the Cygwin->H8300 cross-compiler gcc. Max. (23 years ago, 9-Dec-02, to lugnet.robotics.rcx.legos)
|
| |
| | Re: installation of cygwin and legos/brickos
|
|
John, It looks as if you don't have the cross compiler or it is is not in a known directory. Try searching your entire hard drive for h8300. That might bring something up. You should have either tired to build the cross compiler or downloaded it (...) (23 years ago, 9-Dec-02, to lugnet.robotics.rcx.legos)
|
| |
| | Re: Installation Help!
|
|
Thanks for the info! I checked and I do have grep installed. But I did not install anything other than was listed. I initially tried to install everything but the download died after a couple of hours on my T1 connection. Would some kind person with (...) (23 years ago, 9-Dec-02, to lugnet.robotics.rcx.legos)
|
| |
| | Re: Installation Help!
|
|
(...) Hi Max, I got: $ gcc -v BASH: gcc: command not found but the command I am running to get all this output is the buildgcc.sh command to build gcc. Andy (23 years ago, 9-Dec-02, to lugnet.robotics.rcx.legos)
|
| |
| | want to get inentors kit but...
|
|
Is it true you need windows 98 to run it on? If so, is there anyway around this, coz I only have windows ME or red hat 6.2 linux (I'd rather use windows). Also, why does it cost $189 in the USA (about £120) and in the UK it costs £159 ? Is this lego (...) (23 years ago, 9-Dec-02, to lugnet.robotics)
|
| |
| | Re: modular bot
|
|
yeah the head can eat its tail :) but worm-walk can be done like wave or something like that so what do you think about it it's needed to have many rcxes :) regards pixel "Tobbe Arnesson" <StPnAtM@lotek.nu> wrote in message (...) (23 years ago, 9-Dec-02, to lugnet.robotics, lugnet.technic)
|
| |
| | Re: modular bot
|
|
<<snip>> (...) I see three, four bot's chasing it's own tail in a typical puppy manner :) Best regards, /Tobbe (URL) SPAM when e-mailing) (23 years ago, 9-Dec-02, to lugnet.robotics, lugnet.technic)
|
| |
| | Re: Ultimate Builders Set for Mac?
|
|
All the instructions on the UBS CD are jpegs and quicktime movs. This means that you can read them on a mac without using virtual PC, and if you have Quicktime Pro, you can join them all together as a slide show. Look on the CD in shared/build. I (...) (23 years ago, 9-Dec-02, to lugnet.robotics.rcx)
|
| |
| | Re: Mechanical pneumatic switch
|
|
(...) (23 years ago, 8-Dec-02, to lugnet.robotics)
|
| |
| | Re: Ultimate Builders Set for Mac?
|
|
James, Thanks for the helpful info! If a PC is really needed only for reading the build instructions, do you think I could read them using Virtual PC running on my Mac? Dean (...) (23 years ago, 9-Dec-02, to lugnet.robotics.rcx)
|
| |
| | Re: Ultimate Builders Set for Mac?
|
|
The LEGO pieces you get with the Ultimate Builders Set are a nice addition to any collection. However, the software with all the instructions for all the models only runs on the PC. All the behaviors are completely possible with Robolab but without (...) (23 years ago, 9-Dec-02, to lugnet.robotics.rcx)
|
| |
| | Ultimate Builders Set for Mac?
|
|
We use Robolab software and the RCX on our Power Macintosh G3. Will the Ultimate Buiders Set work for us in that environment? Dean (23 years ago, 8-Dec-02, to lugnet.robotics.rcx)
|
| |
| | Re: installation of cygwin and legos/brickos
|
|
(...) Saw this problem before. You might check older mails in this newsgroup discussing that. Running brickOS under Linux I don't know much about the cygwin problems. But your makefile assumes that the c compiler can be run with the command "cc" (...) (23 years ago, 8-Dec-02, to lugnet.robotics.rcx.legos)
|
