 | | Re: Voltage Sensor
|
|
(...) Hello Nathan, At this stage I am wanting to include this sensor as part of a larger suite of components - Voltage regulator and Trickle charger. Ultimately I want to etch all of these circuits onto a single board and tuck it away in a lego (...) (24 years ago, 18-Sep-02, to lugnet.robotics)
|
| |
 | | Re: Replacement RCX Cost?
|
|
(...) I just ordered one 9709 from this store for $69.95 + $8.95 shipping. John Hansen (24 years ago, 18-Sep-02, to lugnet.robotics)
|
| |
 | | Re: Voltage Sensor
|
|
(...) Thanks Peter, Yes, it was brought to my attention that the useful portion of a 12V battery is at the top end of the voltage range. I don't think I thought about it to be honest - I guess the learning curve just keeps pointing up at this stage. (...) (24 years ago, 18-Sep-02, to lugnet.robotics)
|
| |
 | | Re: Voltage Sensor
|
|
(...) I presume you're using a 12V lead-acid or NiCd battery. As the battery discharges, the output voltage drops, slowly at first but then faster when it gets close to being empty. By the time it reaches, say, 10V, it's time to recharge it. So when (...) (24 years ago, 18-Sep-02, to lugnet.robotics)
|
| |
 | | Handy Board for sale
|
|
Hi, forgive me if you already saw this note on the Handy Board Yahoo group. I have a Handy Board that is over two years old I'd like to sell. It has been stored in a project box so it is still in great condition. I just recharged it and downloaded (...) (24 years ago, 18-Sep-02, to lugnet.robotics.handyboard)
|
| |
 | | Re: Voltage Sensor
|
|
Tom, it is possible to also buy ready made voltage sensors for the RCX, see (URL) have used a most of the sensors from this company for data-logging purposes, but have not yet used the voltage sensor. If you would like more info, I can probably try (...) (24 years ago, 18-Sep-02, to lugnet.robotics)
|
| |
 | | Re: Replacement RCX Cost?
|
|
Rob's suggestion of calling the LEGO Outlets is the best bet. The Dawsonville, Georgia store has a bunch of the 9709, which is the 1.0 RCX (external jack version) brick only. Last time I picked some up they were around $60. jt (...) (24 years ago, 18-Sep-02, to lugnet.robotics)
|
| |
 | | Re: Replacement RCX Cost?
|
|
(...) Well, an entire gazillion piece set *including* an RCX costs at most ~$200 from normal (ie non "educational") sources. (...) power socket? Probably the school will want that kind in preference to the 1.5 or 2.0 versions. I guess it depends on (...) (24 years ago, 18-Sep-02, to lugnet.robotics)
|
| |
 | | Re: Replacement RCX Cost?
|
|
(...) Assuming all you need is the brick and not the entire RIS, there are new v1.5 and v2.0 RCX bricks on BrickLink at: (URL) less than $90. You may also want to try the various LEGO stores listed in the side bar of: (URL) the 9709 v1.0 RCX which (...) (24 years ago, 18-Sep-02, to lugnet.robotics)
|
| |
 | | Replacement RCX Cost?
|
|
Our school has to replace two RCX's that 'walked' last year. Any better price around than $199 at Pitsco?? Thanks! (24 years ago, 17-Sep-02, to lugnet.robotics)
|
| |
 | | Re: Voltage Sensor
|
|
Hello again, if you have difficulties making sense out of my previous posting, try viewing it with a fixed-width font. Otherwise all fomulas will ook scrambled. In the Web interface, "view raw message" is likely to work for that purpose, but of (...) (24 years ago, 17-Sep-02, to lugnet.robotics)
|
| |
 | | Re: Voltage Sensor
|
|
Hello Tom, (...) Yes. You need a low impedance output driving 0..5V into the RCX, thus overriding its internal pullup. (...) Actually, I should have written "resolution" instead of "accuracy". The 10..15V range spans 5V with 256 steps, giving you a (...) (24 years ago, 17-Sep-02, to lugnet.robotics)
|
| |
 | | Evansville LEGO Robotics Competition
|
|
For Immediate Release! Ivy Tech State College and the Evansville chapter 73 of The Society of Manufacturing Engineers announce the Student Robotics Challenge IV titled 'The Eliminator'. This event is similar to our last competition with (...) (24 years ago, 17-Sep-02, to lugnet.robotics.events, lugnet.loc.us.in.eva)
|
| |
 | | Re: Picking up CDs.
|
|
I worked on a similar project about a year ago. I needed to put a small mark on the inside the a CD ring at a certain spot (or pretty near). I had to do this to 4000 CD's. I don't have access to the odd air cylinders, so I had to make do with other (...) (24 years ago, 17-Sep-02, to lugnet.robotics)
|
| |
 | | Re: Voltage Sensor
|
|
Caution: the your external supply has one side connected to RCX ground, which is itself connected to sensor input connector right side. Whichever circuit you choose, you will have to make sure that sensor connector will not be reversed (the (...) (24 years ago, 17-Sep-02, to lugnet.robotics)
|
| |
 | | Re: Can anyone Remote Control RCX ?
|
|
(...) There are multiple ways in BricxCC to remotely control the RCX. You can use the Brick Joystick (which is pretty cool) to control motor outputs via a joystick or other game controller. You can use the Direct Control dialog to control outputs (...) (24 years ago, 17-Sep-02, to lugnet.robotics)
|
| |
 | | Re: Voltage Sensor
|
|
(...) Thanks Dean, I had some thought in monitoring the battery level directly through RCX. But potentially I wanted to monitor multiple battery sources so I thought I might as well as develop an external sensor. Another thought was that the same (...) (24 years ago, 17-Sep-02, to lugnet.robotics)
|
| |
 | | Re: Voltage Sensor
|
|
(...) It's amazing when you get a different perspective on a problem! While not really applicable for this application the idea is indeed very elegant and saves on a precious input port. I have a spare regulator which I will modify to test this out. (...) (24 years ago, 17-Sep-02, to lugnet.robotics)
|
| |
 | | Re: How to setup gcc and make in cygwin
|
|
I had a go at those instructions then gave up after 3 weeks of trying to get them to work. "Ed Manlove" <emanlove@ieee.org> wrote in message news:H2JupE.J4w@lugnet.com... (...) most (...) no (...) for (...) my (...) (24 years ago, 16-Sep-02, to lugnet.robotics.rcx.legos)
|
| |
 | | Re: Can anyone Remote Control RCX ?
|
|
brickx is the deal. you'll need to make sure that your brick has firmware... there is an easy test in the acutal mindstorms trouble shooter to determine if you do. otherwise brickx is more than capable of taking care of buisness. -tk "Douglas (...) (24 years ago, 17-Sep-02, to lugnet.robotics)
|