To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / *29124 (-20)
  magnetic shaft encoder
 
Hi All, Does anyone in this group have experience with using the KMZ10B (magnetic field sensor) to build a shaft encoder? I am interested in a schema to connect it to the HB, either digital or analog input. Thanks, Willem (25 years ago, 17-Jul-01, to lugnet.robotics.handyboard)
 
  Re: Uploading datalog - some confusion?
 
(...) Are you sure about the handshake, on a PC with a serial IR-tower there is no handshake (not necessairy because the PC is the master and the RCX is the slave). (...) best regards, Stef Mientki (25 years ago, 16-Jul-01, to lugnet.robotics.rcx)
 
  RIS 1.5 at TRU in Canada
 
Whoo hoo-- Toys R Us here in London, Ontario seems to have slashed the price on the RIS 1.5 down to $199CDN (about $120USD). That's a 1/3rd reduction in price and almost as good as the $150 that Future Shop online had last year. Now, how do I (...) (25 years ago, 16-Jul-01, to lugnet.loc.ca.on, lugnet.org.ca.rtltoronto, lugnet.robotics.rcx, lugnet.robotics)
 
  Re: Problems installing in Win98
 
Thanks for the info. I'm downloading the sources for binutils and gcc even as I write this. I'll let you know how it turns out. regards (25 years ago, 16-Jul-01, to lugnet.robotics.rcx.legos)
 
  Re: Repairing torn 9V mini motor axles
 
I find that on this type of plastic glue does not work, you might try plastic weld and a cut-off pin. If you keep the head of one side if the pin and insert this into the shorter of the two pieces (use a mini drill bit to bore into each end of the (...) (25 years ago, 16-Jul-01, to lugnet.robotics)
 
  Re: Problems installing in Win98
 
(...) You will need both source and binary tarballs of gcc and binutils, from the CygWin setup utility. You may also need autoconf, automake, flex, yacc, bison etc. -- or not, I don't know. They were installed when I did my build. You should also (...) (25 years ago, 16-Jul-01, to lugnet.robotics.rcx.legos)
 
  Re: ...venting and questioning....
 
(...) No kidding. Many discussions on Lugnet have echoed this sentiment. The only arguments I've seen so far that make sense are that some people cannot find the item locally, or they have not researched and considered the local cost vs eBay cost, (...) (25 years ago, 16-Jul-01, to lugnet.robotics)
 
  Suggested Makefile Changes
 
'make realclean' causes a rebuild of .depend in legOS/util/dll-src. This is inconsistent with other places .depend files are used. dependency building in the lib branch of the tree is not triggered, and would use the old-style makedepend program, (...) (25 years ago, 16-Jul-01, to lugnet.robotics.rcx.legos)
 
  Re: Problems installing in Win98
 
(...) Thanks for the reply. I looked at your post, sorry I'm not able to comment on what files are needed, I'm just now getting into all this. How difficult was it doing the build on your machine? Could you post or send me the steps you followed or (...) (25 years ago, 16-Jul-01, to lugnet.robotics.rcx.legos)
 
  Re: Problems installing in Win98
 
Yes, it is possible. I have legOS running under Cygwin 1.3.2 (latest net release). I did, however, compile the cross compiler from source. See my post 'Toolchain for Cygwin 1.3.2 (latest)', dated 14/07/01 18:34, 2 posts before yours. Given that (...) (25 years ago, 16-Jul-01, to lugnet.robotics.rcx.legos)
 
  Re: Multiple source files
 
Hi, Assuming you have a.C and b.C, and you want to build b.lx, then the following Makefile fragment will work, if you patch your Makefile.user as given below. **** Begin Makefile Fragment **** all: b.lx # Specify all targets to build b.ds1 b.ds2: (...) (25 years ago, 16-Jul-01, to lugnet.robotics.rcx.legos)
 
  Problems installing in Win98
 
Hello, I am trying to install legOS on a WIN98 machine with cygwin 1.3.2. I am have problems with the cross compiler. I just noticed the statement on (URL) that the cross compiler was compiled against the older version of cygwin and that it won't (...) (25 years ago, 16-Jul-01, to lugnet.robotics.rcx.legos)
 
  Repairing torn 9V mini motor axles
 
My students over the last year have torqued the axles off six 9v mini-motors. I've tried just super-glueing another axle. Unfortunately, I can't seem to keep the glue away from the casing nor get true alignment. I've popped the back off, but can't (...) (25 years ago, 16-Jul-01, to lugnet.robotics)
 
  CVS
 
Hi all I'm trying to get the latest code from the cvs root as anonymous. It doesn't seem to let me login using the anonymous. I'm following the instructions on the sourceforge page: cvs -d:pserver:anonymous...root/legOS login but it tells me (...) (25 years ago, 15-Jul-01, to lugnet.robotics.rcx.legos)
 
  Re: RCX 1.0 polarity
 
I see this question has been answered in other posts! I'll look first next time. ;-} Cheers! (...) (25 years ago, 15-Jul-01, to lugnet.robotics)
 
  Re: Programming VC
 
Hi Alberto, (...) No ! Every region is good for only one event. But you can build your own region to act like one with two events. You have to edit some bitmaps (as described here : (URL) ) Now, if you build a region (two in fact) with red and green (...) (25 years ago, 15-Jul-01, to lugnet.robotics.vc)
 
  Programming VC
 
I have some questions about programming VC. Is it possible to launch two differents events over the same region ? (i.e Do something if it detect blue and other thing if it detect red) Is it possible to combine events from differents regions ? I (...) (25 years ago, 14-Jul-01, to lugnet.robotics.vc)
 
  Re: RCX 1.0 polarity
 
(...) Um. None required. Um. Need to study AC current first. Um... AC doesn't have a polarity (well, it does, but it changes every 120th of a second...). Therefore, it doesn't matter _what_ polarity you put on the center pin. And, since there is a (...) (25 years ago, 15-Jul-01, to lugnet.robotics)
 
  Spirit.ocx
 
Hi, Could someone please email me the spirit.ocx file? I'm am a legal owner of the RCX software, but I cannot find the CD. Thanks. (25 years ago, 15-Jul-01, to lugnet.robotics)
 
  RCX 1.0 polarity
 
Hi! Does anyone know the polarity of the center pin for the AC jack on the RCX 1.0? Many thanks! Darc. (25 years ago, 15-Jul-01, to lugnet.robotics)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR