To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / *27684 (-20)
  Racing Line Follower
 
Hello I've built a line follower which is quite fast (approx 4 secs per lap on the testpad). It consists of two motors, each powering a 2/3 geared large wheel. Two light sensors are attached to the front pivot wheel. The distance between the sensors (...) (26 years ago, 2-Apr-01, to lugnet.robotics)
 
  Re: David Schilling
 
Oh I see. thanx....good luck! (...) (26 years ago, 2-Apr-01, to lugnet.robotics, lugnet.org.us.smart)
 
  Re: David Schilling
 
(...) I built the Killough platform for the March SMART meeting mini-challenge. (SMART is the Seattle Mindstorms and Robotic Techies group.) The basic idea was to build a robot to wander around a table, without falling off, and stop beside a heavy (...) (26 years ago, 2-Apr-01, to lugnet.robotics, lugnet.org.us.smart)
 
  Re: David Schilling
 
I built a Killough platform based on Leo Dorst's site and Doug Carlson's site. I have a quicktime movie and links to Leo's and Doug's sites available at: (URL) this helps! (...) (26 years ago, 2-Apr-01, to lugnet.robotics)
 
  Re: David Schilling
 
Looks like a form of the Killough platform on Leo Dorst's site. The rods appear to provide a 'shell' to keep the blue base from getting stuck in the v area. There are movies of the motion on Doug Carlson's site. I do not have any links handy, but (...) (26 years ago, 1-Apr-01, to lugnet.robotics)
 
  RE: Curved Feet
 
Scott, I see this set frequently on eBay. There are six there now. Just search for "8880". I got two that way. It's a great set, though I feel that the suspension and joints to transmit driving power to the wheels are rather inflexible. Most of the (...) (26 years ago, 2-Apr-01, to lugnet.robotics)
 
  Re: Solar Cell Output (Shell logo)
 
Here's another link. (URL) Regards Micah J. Mabelitini - LUGNET #918 The University of Kentucky SECC Middlesboro Academic Skills Resource Center accutron@kih.net - (URL) (26 years ago, 2-Apr-01, to lugnet.robotics)
 
  Re: Solar Cell Output (Shell logo)
 
(...) I believe the cell is made by Shell's photovoltaics division. (URL) Regards Micah J. Mabelitini - LUGNET #918 The University of Kentucky SECC Middlesboro Academic Skills Resource Center accutron@kih.net - (URL) (26 years ago, 2-Apr-01, to lugnet.robotics)
 
  Re: Solar Cell Output (Shell logo)
 
This is may be a bit Off Topic With all the talk about the lego solar cell, (and cap) I went and got one of each. They are a nice curiosity, but as of right now, I can't seem to find any robot applications. Maybe when the sun comes back to Toronto, (...) (26 years ago, 1-Apr-01, to lugnet.robotics)
 
  David Schilling
 
This has an unusual drive-train, I'd like to see what i does and how it moves. (URL) (26 years ago, 1-Apr-01, to lugnet.robotics)
 
  Re: legocam as alternative input device
 
(...) The only idea I have about that is to write your own virtual serial port to which the VC software points and capture the commands normally send to an RCX. (Is it worth it ?) But if you have the knowledge to do this, you should try the logitech (...) (26 years ago, 1-Apr-01, to lugnet.robotics.vc)
 
  Re: Ideas for new sets?
 
(...) Pokemon Jürgen (26 years ago, 1-Apr-01, to lugnet.robotics)
 
  Re: Shutting off illumination LED on Light Sensor for LIDAR
 
(...) Actually you don't need LegOS, any input set to raw mode with the LEGO firmware will do fine. This is because even in passive mode there is a pull up of 10k to 5V, and in fact the LED is glowing dimly in this mode. Just tried it, I can get raw (...) (26 years ago, 1-Apr-01, to lugnet.robotics)
 
  Re: Question about RIS 1.0
 
(...) The RIS 1.0 can be run from either 12VAC or 12VDC. In either case an internal bridge rectifier supplies the internal circuitry with the proper polarity. Internal power is supplied through an LM2936M 5V regulator (maximum input of 45V BTW) The (...) (26 years ago, 1-Apr-01, to lugnet.robotics)
 
  Re: Question about RIS 1.0
 
(...) Transformers do NOT convert AC to DC. They only convert AC to AC. The DC conversion is performed by four diodes in the RIS1.0. Maximum input is rated at 12V AC or DC (the diodes will take care of the polarity for DC inputs) although the (...) (26 years ago, 1-Apr-01, to lugnet.robotics)
 
  Re: Solar Capacitor
 
(...) Yeah it's for real. There's been alot of discussion about the capacitor on here recently, just do a news search. (26 years ago, 1-Apr-01, to lugnet.robotics)
 
  Solar Capacitor
 
I have been playing with a couple of Lego solar panels and the Capacitors. (URL) label on the capacitor claims a value of 1 farad. Is this value possible in such a small component? I always thought a 1 farad capacitor would need a huge plate area. I (...) (26 years ago, 31-Mar-01, to lugnet.robotics)
 
  Re: Ideas for new sets?
 
(...) ...and they are marketing to children raised on Nintendo. We are responsible to teach children how valuable a "highly flexible mechnical building toy" is. ---...--- $50,000 for Jill Behrman (URL) (26 years ago, 31-Mar-01, to lugnet.robotics)
 
  Re: light sensor multiplexer
 
hi Nitil, that's a nice and simple cirquit, but isn't there anything wrong with the grouding ? (...) -- met vriendelijke groet, Stef Mientki email: s.mientki@ids.kun.nl tel: 024 361 3905 fax: 024 354 1211 Postadres: KUN / fmw 171 Instrumentele (...) (26 years ago, 31-Mar-01, to lugnet.robotics.rcx)
 
  Re: Lego Remote Control - Here's The Scoop
 
what about newmatic switches? all lot of sets have them to (...) (26 years ago, 31-Mar-01, to lugnet.technic, lugnet.robotics)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR