To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / *27434 (-20)
  Re: Request: I2C Bus Handy Board interface Info.
 
I recently found an I2C driver at the Image Craft web page under their user contributed software page (URL) P. Loy andyl@citlink.net aloy1@utk.edu "Andrew Loy" <andyl@citlink.net> wrote in message news:G9yJDD.MpD@lugnet.com... (...) (26 years ago, 22-Mar-01, to lugnet.robotics.handyboard)
 
  New Site
 
I have created a new site as a reference for educators using RoboLab in the classroom. I would love to have some of you visit the site and provide feedback. At present we have only a few examples, but we are working on adding many more. The most (...) (26 years ago, 22-Mar-01, to lugnet.robotics.rcx.robolab, lugnet.robotics, lugnet.edu, lugnet.robotics.edu, lugnet.robotics.events.robot-arena, lugnet.robotics.rcx, lugnet.publish.html, lugnet.loc.us.in) ! 
 
  Re: light sensor multiplexer
 
"Nitin Patil" <gn1721@lycos.com> wrote in message news:GAKC9v.F5A@lugnet.com... (...) With the 0.1uF in parallel with the 4.7K, the voltage on the clock circuit is still above the measurement voltage during the normal read interval. It doesn't (...) (26 years ago, 21-Mar-01, to lugnet.robotics.rcx)
 
  Emergency - Half Dead Robot
 
Hi All, I powered on my handyboard the other day, and the next thing that happened was a click noise and some black smoke from the top left part of the HB (the F1, U13 area). I tried to repower it (after turning it off) and nothing happened. I (...) (26 years ago, 22-Mar-01, to lugnet.robotics.handyboard)
 
  Re: light sensor multiplexer
 
(...) Regarding the power used I think you are correct since it is or the order of few microamp. but even then your design can not ( rather Do not ) switch power. Also what I did not like in your desigh is 4.7K resistor. which changes reading in (...) (26 years ago, 21-Mar-01, to lugnet.robotics.rcx)
 
  Re: light sensor multiplexer
 
In lugnet.robotics.rcx, Rainer Balzerowski writes: hi Rainer (...) This is not true since you need to maximum of 60ms after that time out occurs in microconterolor and it chanes the sensor. yes that is true that it is slow for your application. I (...) (26 years ago, 21-Mar-01, to lugnet.robotics.rcx)
 
  Re: light sensor multiplexer
 
(...) I'll bet you can't even measure the power used in the two CMOS parts. Why don't you publish your design so we can pick on it? Michael Gasperi (26 years ago, 21-Mar-01, to lugnet.robotics.rcx)
 
  Ooooops!
 
Ingore the message where I wrote that the RCX didn´t start. It started without showing the "4th" on the lcd screen. Does anyone know how to do that? I mean that when you press the "ON - OFF" button it beeps and shows the "4th" or something. Just so (...) (26 years ago, 21-Mar-01, to lugnet.robotics.rcx.pbforth)
 
  Re: light sensor multiplexer
 
Hi Nitin, (...) Yes, sadly but true. That's why I have to use a battery anyway. (Or an output, but I would save it for other tasks.) (...) I understand. I should have explained what i'm doing with the sharps, sorry. I have a task running, that (...) (26 years ago, 21-Mar-01, to lugnet.robotics.rcx)
 
  Re: Bug in RCX 2.0 beta (Was: RIS 2.0 software now in beta)
 
(...) Hi Sebastian I think you're right in your analysis and TLG may silently have fixed the problem, because if you look at the Vision Command installation, you'll find that some of the SDK DLLs are newer in that release. For fun, I copied the DLLs (...) (26 years ago, 21-Mar-01, to lugnet.robotics.rcx, lugnet.robotics)
 
  Re: light sensor multiplexer
 
Hi Rainer, I do not understand quite your point about timing. Regarding to power sharp takes much more than what your RCX can give ( my measuremants show that RCX gives RMS current of )15 mA only this is not going to drive your sharp at all. (...) (26 years ago, 21-Mar-01, to lugnet.robotics.rcx)
 
  RE: Need for chat server?
 
Well ? :> Have I lost this thread or did you give up on the idea? I would hang around #Robotics, #Cybermaster, #VisionCommand, #NQC, #Mecha and #Market I even would create "my own" channel: #CM-RCX-comms hmmm... ok, just a thought, eheh One problem (...) (26 years ago, 21-Mar-01, to lugnet.robotics)
 
  RE: RCX & Cybermaster (VLL comms and MicroScout)
 
On Tue, 20 Mar 2001, Marco Correia wrote: Actually, if I recall correctly, the sensor inputs are quite happy to accept voltage inputs up to 9V, in RAW mode anyway. It might not be good if they were in an "active" mode, though (rotation sensor, light (...) (26 years ago, 21-Mar-01, to lugnet.robotics)
 
  Battery replacement
 
Hi, Two of my handyboard, pretty old ones have worned out batteries (apparently one element is not charging anymore !!!). I lokked in the digikey catalog for replacement , but the reference doesn't exist any longer !!! What type of element from (...) (26 years ago, 21-Mar-01, to lugnet.robotics.handyboard)
 
  Multiple GP2D02 sensors ?
 
Has anyone successfully connected more than two GP2D02 IR range sensors to the handyboard (with expansion board) ? I would like to impliment 4 sensors and be able to read the range from them all.. Thanks ... .. Rob .. (26 years ago, 21-Mar-01, to lugnet.robotics.handyboard)
 
  Re: light sensor multiplexer
 
(...) Hi Nitin, okay, I see. Sorry, but then your circuit isn't interesting for me. I thought about using Sharp GP2D12 with it, but that won't work. First the Sharps have a current consumption of about 33mA up to 50mA max. Second the Sharps need (...) (26 years ago, 20-Mar-01, to lugnet.robotics.rcx)
 
  Re: Bug in RCX 2.0 beta (Was: RIS 2.0 software now in beta)
 
Dear fellow Lego enthusiasts, so far I did not receive any feedback to my problem report, neither from the newsgroup, nor from Lego technical support. Could somebody please try to confirm that I am not completely stupid in my analysis! Regards, (...) (26 years ago, 20-Mar-01, to lugnet.robotics.rcx, lugnet.robotics)
 
  Preliminary Solar Cell Output Measurements
 
These results are preliminary, but they'll give you some idea of the solar cell's capabilities. Outdoors - Full Overcast Voltage: 3.5V Amperage: 30mA Incandescent Lightbulb - 100W@1" Voltage: 4.1V Amperage: 150mA Indandescent Lightbulb - 100W@6" (...) (26 years ago, 20-Mar-01, to lugnet.robotics, lugnet.dacta)
 
  Re: RCX Crash!
 
Well, acually I wanted to download the pbForth into the RCX because I was reading the book EXTREME MINDSTORMS that you wrote with Dave Baum. In the pbForth chapter I just read trough until I got to the second part. There I needed to test for myself (...) (26 years ago, 20-Mar-01, to lugnet.robotics.rcx.pbforth)
 
  Re: Solar-Powered Hexapod Walker
 
"Micah J. Mabelitini" <micahx@kih.net> wrote in message news:3AB7A891.656ABF...kih.net... (...) Well I guess that would make my model even more like the real thing. i.e. covered in solar cells regards lawrence (26 years ago, 20-Mar-01, to lugnet.robotics, lugnet.technic, lugnet.dacta)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR