 | | Re: 6.8 nF Capacitor
|
|
The 6.6nF was the capacitance measured for the two 6.8nF capacitors that I have managed to get (rated as 10% tolerance). The problem is that the parts listed for the HB are 2% tolerance 6.8nF capacitors which gives a lowest value of 6.6664nF which (...) (26 years ago, 6-Jul-00, to lugnet.robotics.handyboard)
|
| |
 | | Re: 6.8 nF Capacitor
|
|
(...) Yes. Capacitors have typically very loose tolerances anyhow; usually 20% unless you buy specifically selected samples in a tighter tolerance. The 6.8 is a standard value while the 6.6 you have is likely a specially selected non-standard value. (...) (26 years ago, 6-Jul-00, to lugnet.robotics.handyboard)
|
| |
 | | 6.8 nF Capacitor
|
|
Can any body tell me if a 6.6nF capacitor will do to replace the 6.8nF in the IR Transmission circuit (Fred?) ?. Thanks in advance. John Hatton (26 years ago, 6-Jul-00, to lugnet.robotics.handyboard)
|
| |
 | | HB to Comms board cable
|
|
Is there a 'best' length for the telephone cable between the HB and the Comms board. I am about to start construction and I was wondering if there was a maximum length for the cable and if a particular length was recommended. Thanks for your help. (...) (26 years ago, 6-Jul-00, to lugnet.robotics.handyboard)
|
| |
 | | Re: Connect HP 48GX
|
|
Gruezi/ Hi, (...) Instead of using the serial port, how about using the HP4**x IR port? I recall there being HP4**x programs that emulate IR remote controls which should be easy to modify (?) for general-purpose communications. Marco A. Assfalk de (...) (26 years ago, 6-Jul-00, to lugnet.robotics.handyboard)
|
| |
 | | Caution when using DCP container constructs
|
|
In Robolab 2.0 the eight DCP container constructs store the raw value of the sensor. This means the value stored is not in rotations, volts, dB, etc. but in a raw measurement of these values. This raw value cannot be easily used with other Robolab (...) (26 years ago, 5-Jul-00, to lugnet.robotics.rcx.robolab)
|
| |
 | | Minor bug in DCP sound sensor support
|
|
Robolab 2.0 and 2.01 programmer extras has a bug in the DCP sound sensor construct "Wait for increasing sound". This construct sets the sensor type to touch when it should set the sensor type to light. The other sound sensor constructs "Wait for (...) (26 years ago, 5-Jul-00, to lugnet.robotics.rcx.robolab)
|
| |
 | | Handyboard startup problems
|
|
Hi all, I'm having some problems with me previously functioning handyboard. I'm using a standard board which has worked fine for nearly a year. Recently it didn't get any use for awhile and the batteries ran down. After charging them for 18+ hours I (...) (26 years ago, 5-Jul-00, to lugnet.robotics.handyboard)
|
| |
 | | Re: legOS battery life code
|
|
Sorry! I forgot to post the code. Here it is: #include <dsensor.h> #include <dlcd.h> #include <conio.h> int get_battery_mv() { long b; int mv; b = BATTERY; b = ds_scale(b) * 0xABD4L; mv = b / 0x618L; return mv; } int main(int ac, char **av) { int b; (...) (26 years ago, 5-Jul-00, to lugnet.robotics.rcx.legos)
|
| |
 | | legOS battery life code
|
|
Hello, I recently received some code in the mail that when compiled and uploaded to the RCX is supposed to give you the battery life. But when I go to compile it, legOS/util/makelx gives me the following error message: single byte different at (...) (26 years ago, 5-Jul-00, to lugnet.robotics.rcx.legos)
|
| |
 | | Re: 6.8nF Capacitor
|
|
(...) Not knowing what parts the HB uses, but assuming it is something like a polystyrene cap, then I think I have some in my component drawer. Send me your address, and I'll stick a couple in the post. Best Wishes (26 years ago, 5-Jul-00, to lugnet.robotics.handyboard)
|
| |
 | | Re: Interactive Robots
|
|
(...) Quite good. Fantastic site, I have just spend a relaxing 30 minutes browsing it. Keep up the good work. Scott A (...) (26 years ago, 5-Jul-00, to lugnet.robotics.rcx)
|
| |
 | | Re: Submarine
|
|
Flying lego planes.. now there's an idea!! Lets see.. It would have to be big!, and consist mainly of a light technix frame. You would need to use some lego panels attached to the wing frame structure for lift. It would definitely be challenging! It (...) (26 years ago, 4-Jul-00, to lugnet.robotics)
|
| |
 | | Re: VECTOR 2X
|
|
This is my routine to use the Vector 2x with my board (see link below my name) with an I/O expansion board connected. You will need to change the I/O port #defines to work with the Handy Board I/O ports on your expansion board, but other than that (...) (26 years ago, 4-Jul-00, to lugnet.robotics.handyboard)
|
| |
 | | Re: temperature sensor problem
|
|
(...) No problem. Most of the other environments hide this sort of thing programmer, but this relies on the fact that the programming environment knows how each sensor is going to be used. I didn't think this fit with the C philosophy*, so (...) (26 years ago, 4-Jul-00, to lugnet.robotics.rcx.nqc)
|
| |
 | | Re: Submarine
|
|
(...) Yes, I even remember seeing the silly mockup of the N64 controller that controlled it. But the whole thing is a gag. It is not a real submarine. You can see from the Lego parts used what the size is. It is so small that the umbilical would (...) (26 years ago, 4-Jul-00, to lugnet.robotics)
|
| |
 | | Re: Submarine
|
|
(...) (URL) or (URL) these are "old" pages, so many links/photos are offline (URL) remember seeing more, better pictures, one could see the camera inside and the RCX. -end of subject- ___...___ Marco C. aka McViper (26 years ago, 4-Jul-00, to lugnet.robotics)
|
| |
 | | Submarine
|
|
(...) --- Chris Osborn Full System, Inc. fozztexx@fullsystem.com 2160 Jefferson St., #240 (URL) Napa, CA 94559 Webhosting that *works* - 99.99% uptime - First 3 months free (26 years ago, 4-Jul-00, to lugnet.robotics)
|
| |
 | | Re: Has anyone built and ice/snow vehicle?
|
|
(...) one, (...) Already been done (the submarine) (URL) another link, to the LegoSub homepage, but I don't have it here. ___...___ Marco C. aka McViper (26 years ago, 4-Jul-00, to lugnet.robotics)
|
| |
 | | Re: USB IR tower?
|
|
(...) I'm almost certain that the upcoming RCX 2.0 's IR-Tower is USB. (...) A RF comms would be even nicer, like my Cybermaster :) The only advantage of a USB-PBrick instead of a RF-PBrick(+IR to inter-PBrick comms) would be that the PBrick could (...) (26 years ago, 4-Jul-00, to lugnet.robotics)
|