 | | NQC 2.2 now in beta
|
|
See (URL) for more information. Dave Baum (26 years ago, 23-Jun-00, to lugnet.robotics.rcx.nqc)
|
| |
 | | Re: Extra RAM
|
|
To find doors, you can assume that they are are always on a wall. Then, to find an open door, use an edge finding algorithm to highlight the edges. Where there should be a wall, but is not, there must be a door. A closed door could be found by (...) (26 years ago, 23-Jun-00, to lugnet.robotics)
|
| |
 | | Re: Extra RAM
|
|
(...) If you start with a blank map, you don't need a full sized array for mapping. You can build up a linked list or a binary Tree where each node hold position information status and size. If your memory is nearly use up. You start a garbage (...) (26 years ago, 23-Jun-00, to lugnet.robotics)
|
| |
 | | HB for sale
|
|
I am seeling my HB, it was only used for my senior project. Total time of use would be about two weeks. One modification was made to the board which was a differant switch was put on to it to turn it ON and OFF. If you are inteested please e-mail me (...) (26 years ago, 23-Jun-00, to lugnet.robotics.handyboard)
|
| |
 | | Re: global output control
|
|
(...) I thought about this for a while, when I was thinking about "obvert". In one sense, "invert" does imply that inversing again will revert (*grin*), but I don't believe that this meaning is implicit. There is another sense which simply means "to (...) (26 years ago, 22-Jun-00, to lugnet.robotics.rcx.nqc)
|
| |
 | | Re: global output control
|
|
(...) The problem I have with ForwardOutput() and ReverseOutput() is that the terms 'forward' and 'reverse' already have a meaning - specifically they refer to motor directions... Fwd(OUT_A); Rev(OUT_B); If you then 'reverse' the global direction... (...) (26 years ago, 22-Jun-00, to lugnet.robotics.rcx.nqc)
|
| |
 | | Re: Extra RAM
|
|
I think now that either way could be implemented, with special software for the vector map. A bit map you can upload, and just view, but a vector map, you can save space, but when uploaded, you could easily have software to map out the area. The (...) (26 years ago, 22-Jun-00, to lugnet.robotics)
|
| |
 | | Re: Extra RAM
|
|
(...) Ah! I think I see the difference. My concept of the "map" is something that starts out blank and the prime objective is to fill it in. I suspect the use of a term like "door" implies a map supplied from outside. In which case I agree that an (...) (26 years ago, 22-Jun-00, to lugnet.robotics)
|
| |
 | | Re: transmitter IR driver
|
|
(...) Bonk on the "Lego Mindstorms Internals" link under the RCX list. That is the (current) final word. DLC (26 years ago, 22-Jun-00, to lugnet.robotics)
|
| |
 | | Re: Extra RAM
|
|
(...) This really depends on the model you use. If you think of a simple vector map, which only encodes spatial data, you are right. But think of an model, which is divided into to major parts: spatial data and object data. The spatial data (...) (26 years ago, 22-Jun-00, to lugnet.robotics)
|
| |
 | | Re: Extra RAM
|
|
I feel compelled to add that using a bit map greatly simplifies the code involved in handling a map. And it allows mapped features to be classified easily too. Each byte, in a 2D "map" array represents a patch in the real world (a paxel? or loxel (...) (26 years ago, 22-Jun-00, to lugnet.robotics)
|
| |
 | | transmitter IR driver
|
|
hello I seek drivers or documentation, to use the transmitter IR of the lego in personnel applications. (like remote control....) Can you help me? Samuel LIARD (26 years ago, 22-Jun-00, to lugnet.robotics)
|
| |
 | | RE: global output control
|
|
(...) Ummm, how about... ReverseOutput(const int outs); // global reverse ForwardOutput(const int outs); // global fwd Reverse kind of implies invert, but I don't think that will matter to many folks... Cheers, Ralph Hempel - P.Eng ---...--- Check (...) (26 years ago, 22-Jun-00, to lugnet.robotics.rcx.nqc)
|
| |
 | | Re: Extra RAM
|
|
(...) How much resolution do you want to have and what for? If i think of an high resolution map, I think of vectors not bit maps. Esp. in a high resolution environment, you are much better and faster with vectors than with bit maps. If you imaging (...) (26 years ago, 22-Jun-00, to lugnet.robotics)
|
| |
 | | Re: Another pneumatic compressor and pressure switch designs
|
|
(...) I've used two of the little pumps in conjunction with two Air Tanks. I takes 15-20 sec. to fill up the tanks and afterwards you can operate a pneumatic cylinder every 2.5 - 3 sec. for about 15 min. while the compressor is running coutinously. (...) (26 years ago, 22-Jun-00, to lugnet.build, lugnet.robotics, lugnet.technic)
|
| |
 | | HB site down, use alternate
|
|
hi all, we are working through a hardware crash of the primary HB web site server machine. for now, please use instead: (URL) (26 years ago, 22-Jun-00, to lugnet.robotics.handyboard)
|
| |
 | | Re: Another pneumatic compressor and pressure switch designs
|
|
Hello, if you need a rich air source you should something like this. (URL) don't know how to explain it in english. It has a hand air pressure pump, a great tank of 5 liters and you should put no water inside the tank if you use it with Lego Ralf (...) (26 years ago, 22-Jun-00, to lugnet.robotics)
|
| |
 | | LCD Memory Map
|
|
I am just checking that I have got the LCD operation right so I apologise to anybody who is already clear on this. On the LCD module the Register select and Read/Write pins are connected to the A9 and A8 lines of the HB and the DB0-DB7 pins are (...) (26 years ago, 22-Jun-00, to lugnet.robotics.handyboard)
|
| |
 | | Re: Another pneumatic compressor and pressure switch designs
|
|
(...) Methinks you are going to need some of the blue airtanks (26 years ago, 22-Jun-00, to lugnet.build, lugnet.robotics, lugnet.technic)
|
| |
 | | Re: global output control
|
|
(...) We must have the same twisted sense of humor since the necessity of putting it in the FAQ pretty much tipped the scales for me. ObvertOutput() it is! Dave p.s. We'll see if I'm still laughing when people start e-mailing me about it. (26 years ago, 22-Jun-00, to lugnet.robotics.rcx.nqc)
|