 | | cat out of bag, sort of :)
|
|
I prematurely posted an 0.2.4 version of legOS (mainly just right out of CVS) on sourceforge. I've asked Paolo and others to review it for me before we make an "official" announcement, so there isn't one yet (I'd like to post it to freshmeat and (...) (26 years ago, 14-Jun-00, to lugnet.robotics.rcx.legos)
|
| |
 | | Re: legOS 0.2.4 on Win NT 4.0 WS
|
|
Ooops, fixed - sorry - if only all bug-resolutions were as fast .... Now where was that pint .... (...) (26 years ago, 14-Jun-00, to lugnet.robotics.rcx.legos)
|
| |
 | | legOS 0.2.4 on Win NT 4.0 WS
|
|
Hi All, I've just successfully installed legOS 0.2.4 on Win NT and run the demo programs, all thanks to Lius' instructions. I did have one small difficulty though, with both the gzip file and CVS versions at sourceforge - it's tiny ... It was a (...) (26 years ago, 14-Jun-00, to lugnet.robotics.rcx.legos)
|
| |
 | | CVS screwup- sorry
|
|
I checked in a patch to config.h last night that had too many whitespaces and it broke the build. Sorry. I've fixed it now. Luis ---...--- "Going to California with an aching in my heart. Someone told me there's a girl out there with love in her (...) (26 years ago, 14-Jun-00, to lugnet.robotics.rcx.legos)
|
| |
 | | Re: Specification for Adapter for RCX
|
|
Ram Meenakshisundaram schreef: (...) Mine is a 230 VC AC to 10V AC adapter, output 7VA. (26 years ago, 14-Jun-00, to lugnet.robotics)
|
| |
 | | Re: Specification for Adapter for RCX
|
|
I have been using a switchable Radio Shack wall transformer for a while. Make sure its the AC input/AC output style! Set to 9 volts, I used the RcxCC diagnostic panel to view the "battery voltage" at 9.6 volts. That is within spec, because its what (...) (26 years ago, 14-Jun-00, to lugnet.robotics)
|
| |
 | | Re: Specification for Adapter for RCX
|
|
(...) I stand corrected. (26 years ago, 14-Jun-00, to lugnet.robotics)
|
| |
 | | Re: Specification for Adapter for RCX
|
|
Matthew Miller wrote in message ... (...) Sure they do, go to: (URL) Spare Parts, Tools, & Resources - LEGO Dacta Spare Parts - Miscellaneous: Adapter, Identifier: W979833 Allows the RCX to operate from a main power supply rather than from (...) (26 years ago, 14-Jun-00, to lugnet.robotics)
|
| |
 | | Re: Specification for Adapter for RCX
|
|
(...) I don't think Lego makes one. (26 years ago, 14-Jun-00, to lugnet.robotics)
|
| |
 | | Specification for Adapter for RCX
|
|
Hi, I am looking for the EXACT specification for Lego's wall-wart for the RCX. What is its exact power ratings etc. etc? So, if anyone has the Lego wall-wart, can you read the specs out for me. Thanks Ram (26 years ago, 14-Jun-00, to lugnet.robotics)
|
| |
 | | Re: LNP Question
|
|
Hello Colin, (...) (26 years ago, 14-Jun-00, to lugnet.robotics.rcx.legos)
|
| |
 | | Re: HB Memory map
|
|
Device Location Notes ===...=== 6811 internal $0000-$00ff Built-in RAM (A1 chip) $0000-$01ff (E1 chip) ---...--- 6811 control $1000-$103f Built-in registers ---...--- Expansion I/O $4000-$4fff Memory reads in this range enable the Y1 latch selector, (...) (26 years ago, 14-Jun-00, to lugnet.robotics.handyboard)
|
| |
 | | Re: LNP Question
|
|
"Colin Ryan" <colin.ryan@cs.tcd.ie> ha scritto nel messaggio news:394758BE.3DEA88....tcd.ie... (...) I'm working to a porting of lnpd for Win32, but it's not finished yet... Bye, Paolo. --- Indecision is the key to flexibility. (26 years ago, 14-Jun-00, to lugnet.robotics.rcx.legos)
|
| |
 | | Re: Interfacing BASIC Stamp and Lego?
|
|
In a flee market, I stumbled upon an Swedish electronics magazine with Lego on its cover. Of course, I had to buy it. :) The article's header read: "LightFinder - Controlling Robots using BASIC Stamp". The article is of course in Swedish but if (...) (26 years ago, 14-Jun-00, to lugnet.robotics)
|
| |
 | | Re: Motors spinning at startup
|
|
The problem is the same with LEGO-gear-motors. Even worse, the post says "... put a wire to the can ..." but how can you do this with a plastic device? Any help appreciated. Dirk (26 years ago, 14-Jun-00, to lugnet.robotics.handyboard)
|
| |
 | | LNP Question
|
|
Hi All, Apologies if this should be obvious., but I'm curious as to how I can build a windows based LNP application, can it be done? I see that most LNP discussions to date are Linux and LNPd oriented, which would lead me to believe that my only (...) (26 years ago, 14-Jun-00, to lugnet.robotics.rcx.legos)
|
| |
 | | Re: Help needed: Problems setting up the IR tower
|
|
(...) Have you already tried with a new 9V battery in the IR tower? Antonio (26 years ago, 14-Jun-00, to lugnet.robotics.rcx)
|
| |
 | | Re: Help with make in Windows
|
|
Ah...progress. I have finally started tracing the function calls. Did I mention my head hurts? :-p Seriously, what I found was in the 0.2.2 on Windows Instructions, number 8 says "Change the CINC variable definition in legOS\Makefile.common to (...) (26 years ago, 14-Jun-00, to lugnet.robotics.rcx.legos)
|
| |
 | | Re: legOS built on NT - what now
|
|
Colin, what version of legOS did you install? -- Gary (...) (26 years ago, 14-Jun-00, to lugnet.robotics.rcx.legos)
|
| |
 | | Re: Help needed: Problems setting up the IR tower
|
|
I have tried both Andi Scharfstein´s and Reinis Kanders´ recommendations and everything seems ok but there was no improvement... The comm port works fine with my PalmPilot craddle but not with my IR tower...Does anyone else have another (...) (26 years ago, 14-Jun-00, to lugnet.robotics.rcx)
|