To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / *1501 (+10)
  Re: Polaroid Sonar
 
Sriram, (...) It is on the outer edge of the module neer the ribbon cable connector. Its exact location is indicated by a circle with a + sign to indicate the polarity. (...) I simply (temporary) soldered to the connector at the end of the ribbon (...) (30 years ago, 18-Feb-97, to lugnet.robotics.handyboard)
 
  running .s19
 
Hello, I am trying to use normal .asm files assembled with as11 on the handy-board. I am not using IC. Although my .s19 file downloads fine I don't think it is being run. My code begins at $D000. I use an ORG statement to set $BFFE:$BFFE to $D000. (...) (30 years ago, 19-Feb-97, to lugnet.robotics.handyboard)
 
  Re: running .s19
 
does your program to anything else other than attempt to leave special mode? You could have it write a value to the motor address ($7000); that would be a more visible indication that it is running. BTW, why is your first instinct to take it out of (...) (30 years ago, 19-Feb-97, to lugnet.robotics.handyboard)
 
  Re: running .s19
 
shouldn't you be going into expanded mode, not single chip? (...) (30 years ago, 19-Feb-97, to lugnet.robotics.handyboard)
 
  Re: Motors & handyboard
 
(...) Why not use the H-bridge that is already on the bulldozer? If you work backwards throught the motor driver circuitry, or use the RF controller to send commands to the dozer and see what voltages change you can figure out where the inputs to (...) (30 years ago, 19-Feb-97, to lugnet.robotics.handyboard)
 
  Re: Motors & handyboard
 
(...) This is also excellent advice. On one R/C car I had, I ended up having to simulate the signal input to the controller because the h-bridge was so screwy but it does save you from having to build your own. On a related note, Radio Shack sells (...) (30 years ago, 19-Feb-97, to lugnet.robotics.handyboard)
 
  Digit outputs....
 
I've tried to program the digital outputs from the SPI header J6 on the HB with no success. I pump the values into the HB as per instruction form the FAQ note and measure the 4 outputs. No high/low, just some sort of oscillation. What could be my (...) (30 years ago, 20-Feb-97, to lugnet.robotics.handyboard)
 
  Re: Digit outputs....
 
Rather than trying to figure out the hex for the bits, I use the IC binaray number format, "0b". I set the bits using a binary mask, for example, to set the MOSI pin high, I use: bit_set(0x1008, 0b00001000) then to set the MOSI pin low, I use: (...) (30 years ago, 20-Feb-97, to lugnet.robotics.handyboard)
 
  SPI Routines in IC
 
Anybody have any routines or know of any published information for using the SPI with IC for: ...use with Dallas Semi's serial real time clock - DS1202 ...use with 12 Bit serial A/D - LT1298 ...use with Dallas semi's Thermomerter - DS1620 Thanks a (...) (30 years ago, 21-Feb-97, to lugnet.robotics.handyboard)
 
  motor drivers
 
Hi all, I am running some motors from a Mini Board and I want to up the current output of the board. I have noticed that the motor drivers on the MB are the L293 chips just like the Handy Board. Now if the 1 Amp motor chips that many Handy Board (...) (30 years ago, 21-Feb-97, to lugnet.robotics.handyboard)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR