 | | Angle Sensor
|
|
Hi, Can someone tell me how the angle sensor works? Is it giving a RAW value back, or maybe even a real angle (between 0 and xxx, with step 1)? Where can I get the angle sensor in Europe (The Netherlands)? Thanks in advance... Michel -- Did you (...) (28 years ago, 27-Mar-99, to lugnet.robotics)
|
| |
 | | Re: Handy Board inputs
|
|
Hi Becky, If you are using the HB with the expansion board, you *do* need new library files loaded. Check the web site at: (URL) easiest way to run new library files is to edit lib_hb.lis to include them. To test the HB inputs w/o the expansion (...) (28 years ago, 27-Mar-99, to lugnet.robotics.handyboard)
|
| |
 | | Re: Angle Sensor
|
|
(...) The Lego rotation sensor counts each rotation in 16 steps starting from 1 (no. # 2 to 17 for the first full rotation). If the rotation goes backwards the count is negative (no. # 0 to -15 for the first full backward rotation). The count is (...) (28 years ago, 27-Mar-99, to lugnet.robotics)
|
| |
 | | Re: Angle Sensor
|
|
One of the best suggestions (maybe from Ralph Hempel??) that I have seen for this sensor is to gear it up (down?) to get the desired rotational resolution. -Rob Doucette. Franz-Michael S. Mellbin wrote in message ... (...) (no. (...) 1 + (...) that (...) (28 years ago, 27-Mar-99, to lugnet.robotics)
|
| |
 | | RE: Angle Sensor
|
|
(...) Nope, wasn't me...I'll bet the fancy LEGO milling machine does something like it though... Maybe I should buy a rotation sennsor first :-) Cheers, Ralph Hempel - P.Eng ---...--- Check out pbFORTH for LEGO Mindstorms at: (URL) ---...--- Reply (...) (28 years ago, 27-Mar-99, to lugnet.robotics)
|
| |
 | | Re: Angle Sensor
|
|
Well, then I guess I need to build my own rotation sensor using a "Potmeter" (variable resistor) because I need a real angle, actually I need an angle per time value. Is this is possible? I saw something about this on a website in the mindstorms (...) (28 years ago, 27-Mar-99, to lugnet.robotics)
|
| |
 | | Help needed!
|
|
Hi, I have assembled my recently bought Handy Board kit and have run into major problems: In paragraph 6.0.5 of the assembly manual, the Handy Board is tested for the microprocessor and memory circuits. After powering up the board and running IC (...) (28 years ago, 28-Mar-99, to lugnet.robotics.handyboard)
|
| |
 | | King of the hill
|
|
Howdy, I'm looking for fellow Mindstormers in the Houston, Texas area for sparing. Basicaly, I want to try a "king of the hill" type of competition. White circular field, black border (say black electrical tape), last robot inside the field wins. (...) (28 years ago, 28-Mar-99, to lugnet.robotics.events)
|
| |
 | | Light Sensor Non Destructive Mods
|
|
Hi All, I've just added a new page to my website that describes a non-destructive mod to the light sensor that actually allows it to read ambient light! (URL) The range is <10 for a dark box and >90 for a halogen lamp about 6 feet away. It's really (...) (28 years ago, 28-Mar-99, to lugnet.robotics, lugnet.robotics.rcx.pbforth)
|
| |
 | | Java class libraries for HandyBoard
|
|
Users interested in running Java on HandyBoard can now download demonstration application and a set of library class files at (URL) Gasparik (28 years ago, 28-Mar-99, to lugnet.robotics.handyboard)
|
| |
 | | Polaroid Sonar Device fried!!!!
|
|
The C3279 chip ("Q1") on my sonar device fried. I checked the expansion board and it is assembled correctly. I am not sure why it would fry. I added the 0.1uF electrolytic capacitor to C7 position as stated in the sonar.html site and suggeted by an (...) (28 years ago, 28-Mar-99, to lugnet.robotics.handyboard)
|
| |
 | | Re: Angle Sensor
|
|
(...) So long as your software remembers to count the revolutions, it's surely very simple to gear the Lego sensor to get a real angle... however for your idea below, you might need much too much gearing! (...) You shouldn't need fuzzy logic to do (...) (28 years ago, 28-Mar-99, to lugnet.robotics)
|
| |
 | | RE: Angle Sensor
|
|
(...) Oh Oh, time to get on the flame suit. I agree with Stuart. Fuzzy logic was one of those fads that was to be applied to ALL control systems. The problem is that many control system problems are well understood and solutions are already in (...) (28 years ago, 28-Mar-99, to lugnet.robotics)
|
| |
 | | Re: Angle Sensor
|
|
In article <000e01be788c$3c95fe...@p200mmx>, Michel Verhagen <mive@xs4all.nl> writes (...) Someone posted a URL of a balancing machine recently which used fuzzy logic. Try deja news. (28 years ago, 28-Mar-99, to lugnet.robotics)
|
| |
 | | Re: Help needed!
|
|
MSMKatz wrote: <snip> (...) <snip> Marc, I wonder if the hardware is perfectly ok, but you're inadvertently attempting to load the wrong software. I'm not sure where your lib_hs.lis came from or why IC automatically loads it, but I think it might be (...) (28 years ago, 28-Mar-99, to lugnet.robotics.handyboard)
|
| |
 | | Re: Polaroid Sonar Device fried!!!!
|
|
(...) The most common causes would probably be: (1) Not having a transducer hooked up when the ping is initiated; (2) Having the flat flex cable plugged in backwards (you can't trust the stripe to be on the correct side! Make sure pin 1 goes to (...) (28 years ago, 28-Mar-99, to lugnet.robotics.handyboard)
|
| |
 | | legOS Network Protocol
|
|
Markus, I have been away for the last week or so. What have I missed in the discussion on LNP? I would like to get cracking on this. I have 2 or 3 guys over here who want to get into this too. -Jake Jacob S. Barrett jsbarrett@acm.org (28 years ago, 28-Mar-99, to lugnet.robotics.rcx.legos)
|
| |
 | | Re: Angle Sensor
|
|
Your missing one very important fact here: With the equations you gave, the pole can't be a variable size, can it? Anyway, of course all problems solved with fuzzy logic can be solved using "normal" equations, but I'm a student and I'm now following (...) (28 years ago, 28-Mar-99, to lugnet.robotics)
|
| |
 | | Help needed! Additional info
|
|
Hi everybody! Will Bain alerted me that I was using the wrong library files. I've corrected this, but am still having the "board not responding" problem! Any help on this is still very much welcome!! Thanks and best regards, Marc msmkatz@wxs.nl (...) (28 years ago, 28-Mar-99, to lugnet.robotics.handyboard)
|
| |
 | | Re: GCC 2.8.1 for HC11
|
|
(...) How come you didn't simply use the 2.6.3 cross-compiler? I doubt the optimizer is improved _that_ much for the HC11. (...) It was a while ago, and I don't remember how much of Carlos's work is left. It all had to be converted to the new (...) (28 years ago, 29-Mar-99, to lugnet.robotics.handyboard)
|