To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.org.ca.rtltorontoOpen lugnet.org.ca.rtltoronto in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Organizations / Canada / rtlToronto / 5376
  Re: Is it wrong to cut up flex tubing?
 
"Derek Raycraft" <derek.raycraft@sitraka.com> wrote in message news:3D86611F.506050...aka.com... (...) ::scratches head:: I can't picture what piece you're talking about: "those 1x2 plates with the groves on the sides". I'm really curious about what (...) (22 years ago, 17-Sep-02, to lugnet.org.ca.rtltoronto)
 
  Re: Is it wrong to cut up flex tubing?
 
(...) Snipped - The message and the hoses :) I believe that Derek is talking about this peice. (URL) VW (22 years ago, 17-Sep-02, to lugnet.org.ca.rtltoronto)
 
  Re: Is it wrong to cut up flex tubing?
 
(...) (URL) over in .trains posted a design for low profile trucks that used flex tubing and uses that door rail part.... this post is the start of a thread about it. (URL) might not be what was meant though. Hope that helps. 1 - collaborative (...) (22 years ago, 17-Sep-02, to lugnet.org.ca.rtltoronto)
 
  Re: Is it wrong to cut up flex tubing?
 
(...) will the REAL derek please stand up? BTW cut NOTHING!!! I don't cut my lego parts and I'm a better man for it..... Sure my Search sub and 8460 look a bit odd, but i still have very long pneumatic tubing. Fight the urge, be lego pure. :) . .. (...) (22 years ago, 17-Sep-02, to lugnet.org.ca.rtltoronto)
 
  Re: Is it wrong to cut up flex tubing?
 
(...) Yes this is one of the parts I'm talking about, but I don't think it's the one Iain is wondering about. Derek (22 years ago, 17-Sep-02, to lugnet.org.ca.rtltoronto)
 
  Re: Is it wrong to cut up flex tubing?
 
(...) Yes I think this is the part Iain is wondering about. (...) Yes I'm using a similar design, to what they are talking about in this thread, for my trucks. Derek (22 years ago, 17-Sep-02, to lugnet.org.ca.rtltoronto)
 
  Re: Is it wrong to cut up flex tubing?
 
(...) hehe, what could you be referring too? :-) Actually the point has become moot. As it turns out the interference of other parts has made it unnessisary to cut flex tubing after all. The pneumatic T-connector will do just fine. Its nice to know (...) (22 years ago, 17-Sep-02, to lugnet.org.ca.rtltoronto)
 
  Re: Is it wrong to cut up flex tubing?
 
"Larry Pieniazek" <lpieniazek@mercator.com> wrote in message news:H2L3L5.Hsu@lugnet.com... (...) used (...) flex tubing with this? Iain (STILL confused about the trucks) (22 years ago, 17-Sep-02, to lugnet.org.ca.rtltoronto)
 
  Re: Is it wrong to cut up flex tubing?
 
(...) I'm not sure what was meant by saying flex tubing was used in design of the trucks discused in that thread. I did up a diagram of my truck, but I can't post it at the moment. Hopefully later tonight or tomorrow. Basicly you pop the wheels out (...) (22 years ago, 17-Sep-02, to lugnet.org.ca.rtltoronto)
 
  Re: Is it wrong to cut up flex tubing?
 
(...) Ok so I finish the base of the truck. (URL) is the older design. I still need to find the model for the 2 long half beam so I can model the new design. Derek (22 years ago, 17-Sep-02, to lugnet.org.ca.rtltoronto)
 
  Re: Is it wrong to cut up flex tubing?
 
"Derek Raycraft" <derek.raycraft@sitraka.com> wrote in message news:3D87C15D.803080...aka.com... (...) You guys are so good at this! Iain (22 years ago, 18-Sep-02, to lugnet.org.ca.rtltoronto)
 
  Re: Is it wrong to cut up flex tubing?
 
Sorry to jump into the thread late and dumb, but *doh*... Looking at the rendering... you've captured a flex tube between two of those motor-mounting 2x1 plates with the extra bit on them? And that's your axle for the train? I think that's one of (...) (22 years ago, 19-Sep-02, to lugnet.org.ca.rtltoronto)
 
  Re: Is it wrong to cut up flex tubing?
 
(...) I think you've go it a little mixed up. The wheels in my truck are taken from the 9V train wheel block. (URL) are surprisingly easy to pop out. Never thought of doing this before though. The metal axle that holds the two wheels together is the (...) (22 years ago, 19-Sep-02, to lugnet.org.ca.rtltoronto)
 
  Re: Is it wrong to cut up flex tubing?
 
"Jeff Elliott" <jeffe@telepres.com> wrote in message news:3D89E534.6FE52B...res.com... (...) There isn't any flex tubing in Derek's *axles*, he's got it between the crosses in the 2x1x0.5 beams that are shown as 3x1x0.5 beams. But what I don't get (...) (22 years ago, 19-Sep-02, to lugnet.org.ca.rtltoronto)

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR