Subject:
|
Re: Santa Fe caboose
|
Newsgroups:
|
lugnet.trains
|
Date:
|
Tue, 5 Mar 2002 17:05:59 GMT
|
Viewed:
|
453 times
|
| |
![Post a public reply to this message](/news/icon-reply.gif) | |
> In lugnet.trains, David VinZant writes:
> > Hey Larry I did find this one picture. It may not be as dramatic of a curve
> > but it does have an arc to it.
> > http://www.walthers.com/prodimage/0140/01400000005394.gif
>
>
In lugnet.trains, Larry Pieniazek writes:
> But I'd argue that at LEGO resolution that rounded edge should be lost in
> (wait for it... ) "rounding error". (crowd groans) given the size of it
> compared to the size of one stud or the height of one brick.
I'd agree that the rounded edge is too small to model, but the overall curve
of the roof can still be done. I like to have (in six-wide at least) a
plated roof, with the middle four studs raised by one plate. This isn't my
best example of engine building, but look at the roof here:
http://homepage.ntlworld.com/j.j.railton/taneng/index.html
Where it's built in to an end wall, I have 1 stud of the roof colour showing
either side of the central raised part. If the roof overhangs an open area,
I use 2-wide plates under-lapping[1] the centre 4-wide one, to hide the cracks.
Jason J Railton
[1] If you don't like made-up words, how is the language meant to evolve?
|
|
Message is in Reply To:
![](/news/x.gif) | | Re: Santa Fe caboose
|
| (...) They (the car manufacturers... Pullman Standard, American Car Foundry and others) took big pieces of steel and put them into huge 200++ ton presses and formed ribs and raised/lowered areas into them for strength. They rounded the ends so that (...) (22 years ago, 5-Mar-02, to lugnet.trains)
|
13 Messages in This Thread: ![Santa Fe caboose -David VinZant (4-Mar-02 to lugnet.trains)](/news/x.gif) ![](/news/246.gif) ![Re: Santa Fe caboose -Larry Pieniazek (4-Mar-02 to lugnet.trains)](/news/x.gif) ![](/news/246.gif) ![Re: Santa Fe caboose -David VinZant (4-Mar-02 to lugnet.trains)](/news/x.gif) ![](/news/46.gif) ![Re: Santa Fe caboose -John Neal (4-Mar-02 to lugnet.trains)](/news/x.gif) ![](/news/46.gif) ![Re: Santa Fe caboose -Larry Pieniazek (5-Mar-02 to lugnet.trains)](/news/x.gif) ![](/news/46.gif) !["Super Chief" (was: Santa Fe caboose) -Tony Hafner (5-Mar-02 to lugnet.trains)](/news/x.gif) ![](/news/46.gif) ![Re: "Super Chief" (was: Santa Fe caboose) -Larry Pieniazek (5-Mar-02 to lugnet.trains)](/news/x.gif)
![](/news/x.gif) ![](/news/28.gif) ![](/news/x.gif) ![](/news/68.gif) ![Re: Santa Fe caboose -David VinZant (4-Mar-02 to lugnet.trains)](/news/x.gif) ![](/news/246.gif) ![Re: Santa Fe caboose -John Neal (4-Mar-02 to lugnet.trains)](/news/x.gif)
![](/news/x.gif) ![](/news/28.gif) ![](/news/x.gif) ![](/news/x.gif) ![](/news/68.gif) ![Re: Santa Fe caboose -Larry Pieniazek (5-Mar-02 to lugnet.trains)](/news/x.gif) ![](/news/46.gif) ![You are here](/news/here.gif)
![](/news/x.gif) ![](/news/68.gif) ![Re: Santa Fe caboose -Mark Williams (5-Mar-02 to lugnet.trains)](/news/x.gif) ![](/news/46.gif) ![Re: Santa Fe caboose -Larry Pieniazek (5-Mar-02 to lugnet.trains)](/news/x.gif)
- Entire Thread on One Page:
- Nested:
All | Brief | Compact | Dots
Linear:
All | Brief | Compact
|
|
|
|