 | | Re: MOC 36 Axle Schnabel Car
|
|
(...) Maybe its time to switch to a curve, straight, curve, straight, corner design? Josh (21 years ago, 26-Nov-03, to lugnet.trains)
|
| |
| | Re: DCC chip installed in accessory brick
|
|
In lugnet.trains, David Koudys wrote: <snip> (...) Oh My Goodness!!! THis could get really fun! So I install the Lenz N decoder in a train motor, leaving the 2x2 contact plate alone (still connected to the wheel pickups) Just soldered the pickups to (...) (21 years ago, 26-Nov-03, to lugnet.trains)
|
| |
| | Re: DCC chip installed in accessory brick
|
|
(...) I was thinking exactly this type of scenario at work today--getting a train motor and taking out the motor--just use the contacts--but then I figured that maybe I'll adapt one of my motors so that the 2x2 electric plate stays directly (...) (21 years ago, 26-Nov-03, to lugnet.trains)
|
| |
| | Re: DCC chip installed in accessory brick
|
|
This is great! Don't forget that this device does not have to be stationery but could be incorporated into your mobile wrecker crane for remote control of those tricky salvage operations! You will need some method of picking up the contact to the (...) (21 years ago, 25-Nov-03, to lugnet.trains)
|
| |
| | Re: DCC chip installed in accessory brick
|
|
(...) Dave, I don't know if you already did this, but before you glue it together, consider putting diodes in parallel with the light outputs. This will allow you to run inductive loads like motors and relays with the light outputs without fear of (...) (21 years ago, 25-Nov-03, to lugnet.trains)
|
| |
| | Re: DCC chip installed in accessory brick
|
|
In lugnet.trains, Chris Phillips wrote: <snip> (...) Hey Chris, THere was a post a while back in which someone showed how to take the metal tabs out of the 2x8 brick---by taking a small drill and taking off the plastic holders. I did that for my (...) (21 years ago, 25-Nov-03, to lugnet.trains)
|
| |
| | Re: DCC chip installed in accessory brick
|
|
(...) I'm glad to hear that this worked so well! When I first got into DCC I bought an HO decoder that ended up being just a little bit too big to cram inside a LEGO train motor, and I've been meaning to do this ever since. I was thinking of using (...) (21 years ago, 25-Nov-03, to lugnet.trains)
|
| |
| | DCC chip installed in accessory brick
|
|
(URL) took an HO chip and attached it to a 2x8 electric plate. After an absolute brutal hatchet and soldering job, I started anew and actually made a reasonable job of it. Separated the 2x8 into 4 2x2 electric segments 1 input 1 variable speed (...) (21 years ago, 25-Nov-03, to lugnet.trains)
|
| |
| | Re: A couple of new train things
|
|
(...) (URL) Light Blue Steamer Hi Teunis, those are nice creations! I count a width of 7 studs for the steamer, is that right? 7 is my lucky number.... ;-) (...) (URL) I have googeled it myself just a minute ago. I will try to update the FGLTC-site (...) (21 years ago, 25-Nov-03, to lugnet.trains, FTX)
|
| |
| | Michiana-LUG @ GATS Fort Wayne
|
|
Michiana-LUG's first GATS appearance was a great success and a lot of fun. Report to follow. Here are some pics... (5 URLs) GATS Fort Wayne 2003> Amy (21 years ago, 25-Nov-03, to lugnet.announce, lugnet.trains, lugnet.town, lugnet.org.us.michiana-lug, FTX) !!
|
