Subject:
|
Re: Pneumatic "One Leg at a Time" Robot Circuit
|
Newsgroups:
|
lugnet.technic
|
Date:
|
Tue, 13 Sep 2005 19:12:21 GMT
|
Viewed:
|
7954 times
|
| |
|
|
> > Here's the pneumatic circuit diagram that will allow the above function to be
> > realised, whilst allowing a variable number of legs to be used. The diagram has
> > 2 leg modules in it, but the table shows enough columns for four legs. I
> > suggest that four legs is probably the minimum for stability but I'd be
> > interested to see a stable tripod.
> >
> > http://www.brickshelf.com/gallery/mbellis/Technic/Pneumatics/Building-Blocks/pneumatic_one_leg_at_a_time_robot_circuit.jpg
> >
> > There are 5n+3 steps in the cycle, where n is the number of legs. The circuit
> > uses 3n+1 (or 4n+1) cylinders and 7n+2 valve switches.
> >
> > Load bearing is accommodated by the fact that all the legs share the weight, so
> > if a small pressure drop occurs when a raised foot is lowered, all the other
> > feet would rise a bit rather than one leg rising all the way, and it would equal
> > out by the time the raised foot was fully lowered.
> >
> > As well as walking robots, this circuit lends itself to any function that
> > requires several sub-systems to operate in sequence, with a global reset at the
> > end.
> >
> > Mark
>
> Hi Mark,
>
> Now I know what to build next..... a four legged walker that lifts one leg at
> a time. On paper it looks like I can get one made for 1+2n pistons and 2+4n
> switches. This assumes that legs mechanically lock when weight bearing. I don't
> use pneumatic differential pair logic when making walkers. I stick with single
> switch AND gates that Mark Terrabain turned me on to.
>
> In general I don't think that differential pair logic is the most cost
> effective way to build sequencers because they are so much more expensive to
> implement.
>
> Kev
hi,
why do you wanne build a thing that lifts one leg a time?.... i did it but it
dont have any advanges. it isn't much more stable. it isn't faster (my cat 343
was not to slow) but stil i don't see any inprovments. the only thing is that it
is looking cool!!!
http://brickshelf.com/cgi-bin/gallery.cgi?f=141780
the why it move's is more orgenic then anything i see on 4 legs from lego. but
that is not where you are looking for is'nt it?...
sigurd
|
|
Message has 2 Replies:
 | | Re: Pneumatic "One Leg at a Time" Robot Circuit
|
| "sigurd" <sigurd18@hotmail.com> wrote in message news:IMrs0L.18LJ@lugnet.com... (...) Didn't the Star Wars AT-ATs move one leg at a time? (Going by memory sometimes produces weird results) Rob www.brickmodder.net (21 years ago, 13-Sep-05, to lugnet.technic)
|
Message is in Reply To:
| | Re: Pneumatic "One Leg at a Time" Robot Circuit
|
| (...) Hi Mark, Now I know what to build next..... a four legged walker that lifts one leg at a time. On paper it looks like I can get one made for 1+2n pistons and 2+4n switches. This assumes that legs mechanically lock when weight bearing. I don't (...) (21 years ago, 13-Sep-05, to lugnet.technic)
|
16 Messages in This Thread:
  
 
- Entire Thread on One Page:
- Nested:
All | Brief | Compact | Dots
Linear:
All | Brief | Compact
This Message and its Replies on One Page:
- Nested:
All | Brief | Compact | Dots
Linear:
All | Brief | Compact
|
|
|
|
