 | | Re: Connecting New Cylinders —Mark Riley
|
| | | (...) Well, I don't have any of the new pistons so this may not work, but have a look at this setup (click for larger view): (URL) With the new pistons, you should be able to use the new 1x2 liftarms instead. To get the liftarm to seat properly over (...) (21 years ago, 12-Dec-03, to lugnet.technic, FTX)
|
| | | |
| | | | | Re: Connecting New Cylinders —Philippe Hurbain
|
| | | | (...) It works very well! (URL) Philo (21 years ago, 12-Dec-03, to lugnet.technic, FTX)
|
| | | | |
| | | | | | Re: Connecting New Cylinders —Jonathan MacIntyre
|
| | | | | (...) Thanks Philo for the ideas, I find them very useful. (21 years ago, 13-Dec-03, to lugnet.technic, FTX)
|
| | | | | |
| | | | | | | Re: Connecting New Cylinders —Philippe Hurbain
|
| | | | | | | (...) Rather thank Mark... I just made the photograph :o) Philo (21 years ago, 13-Dec-03, to lugnet.technic, FTX)
|
| | | | | | | |
| | | | | | | Re: Connecting New Cylinders —Kevin L. Clague
|
| | | | | | (...) This solution should also work for small pistons. I'd have less concerns about breaking them due to excess stress. Kevin (21 years ago, 18-Dec-03, to lugnet.technic, FTX)
|
| | | | | | |
| | | | | | Re: Connecting New Cylinders —Tobbe Arnesson
|
| | | | (...) I knew it would be a hassle to connect this new cylinder back-to-back! Too bad TLC did not put an axle hole in it :( I must say Mark's version looks like a winner (right until the inlet pops off :) )! -- Best regards, /Tobbe (URL) (remove SPAM (...) (21 years ago, 17-Dec-03, to lugnet.technic, FTX)
|
| | | | |
| | | | | | Re: Connecting New Cylinders —Paul Kleniewski
|
| | | | i'm just curious is it possible to put piston's vents inside the axlehole? if yes then maybe the rest of vent will stick out enough to still join the tube hmm? pixel "Tobbe Arnesson" <StPnAtM@lotek.nu> wrote in message news:Hq1HJ7.rDH@lugnet.com... (...) (21 years ago, 17-Dec-03, to lugnet.technic)
|
| | | | |
| | | | | | Re: Connecting New Cylinders —Tobbe Arnesson
|
| | | | | (...) Eeehhh... What? /Tobbe (21 years ago, 17-Dec-03, to lugnet.technic)
|
| | | | | |
| | | | | | | Re: Connecting New Cylinders —Paul Kleniewski
|
| | | | | | sorry tobbe :) i'm sure you know what i mean you are just joking right? :)))) pixel "Tobbe Arnesson" <StPnAtM@lotek.nu> wrote in message news:Hq1sqo.13rM@lugnet.com... (...) (21 years ago, 18-Dec-03, to lugnet.technic)
|
| | | | | | |
| | | | | | Re: Connecting New Cylinders —Philippe Hurbain
|
| | | | Hi Pixel, (...) Yes, they fit perfectly (...) Unfortunately no, the pneumatic tube is very loose on the remaining part of the vent :( Philo (21 years ago, 17-Dec-03, to lugnet.technic)
|
| | | | |
| | | | | | Re: Connecting New Cylinders —Paul Kleniewski
|
| | | | hi philo it's a pitty it could be elegant solution :) of course you checked liftarm's axlehole :) ie 1x2 liftarm pixel "Philippe Hurbain" <philohome@free.fr> wrote in message news:Hq1sxr.16Jo@lugnet.com... (...) (21 years ago, 18-Dec-03, to lugnet.technic)
|
| | | | |
| | | | | | Re: Connecting New Cylinders —Ross Crawford
|
| | | | (...) Of course if you could use the thin liftarm it would be better, but I think the wide liftarm is also an elegant solution :) ROSCO (21 years ago, 18-Dec-03, to lugnet.technic)
|
| | | | |
| | | | | | Re: Connecting New Cylinders —Paul Kleniewski
|
| | | | "Ross Crawford" <rosscraw@bigpond.net.au> wrote in message news:Hq36E4.1q4v@lugnet.com... (...) no doubt it is i thought thin liftarm with piston vents inside axleholes could join pistons better (stronger) but wide liftarm is a very good solution (...) (21 years ago, 18-Dec-03, to lugnet.technic)
|
| | | | |
| | | | | | Re: Connecting New Cylinders —Ross Crawford
|
| | | | (...) I think I'd be worried that bending forces when operating the cylinders could cause the thin liftarm to snap the inlet. At least with the wide liftarm, the forces would be carried by a substantially larger area, and with the hose also (...) (21 years ago, 18-Dec-03, to lugnet.technic)
|
| | | | |
