 | | Re: I was thinking about bipedal walkers this morning and....
|
|
(...) Dunno but this non-LEGO robot (with knees) has been taught to run (URL) wish there was a video available on the net somewhere - I saw it on TV yesterday, and though it's difficult to tell it's running, it does seem rather more "human-like" (...) (21 years ago, 18-Dec-03, to lugnet.technic, lugnet.robotics)
|
| |
| | Re: Connecting New Cylinders
|
|
(...) I think I'd be worried that bending forces when operating the cylinders could cause the thin liftarm to snap the inlet. At least with the wide liftarm, the forces would be carried by a substantially larger area, and with the hose also (...) (21 years ago, 18-Dec-03, to lugnet.technic)
|
| |
| | Re: I was thinking about bipedal walkers this morning and....
|
|
(...) Hi Mark, I have never seen a walker like this. I'd be the last person to say it can't be done. Kevin (...) (21 years ago, 18-Dec-03, to lugnet.technic, lugnet.robotics)
|
| |
| | I was thinking about bipedal walkers this morning and....
|
|
Consider the way we walk... we start by effectively starting to lean slightly forward, and we swing a leg some distance in front of ourselves to stop from falling. We then start to bring the other leg forward as we reupright ourselves and repeat the (...) (21 years ago, 18-Dec-03, to lugnet.technic, lugnet.robotics)
|
| |
| | Re: Connecting New Cylinders
|
|
(...) This solution should also work for small pistons. I'd have less concerns about breaking them due to excess stress. Kevin (21 years ago, 18-Dec-03, to lugnet.technic, FTX)
|
| |
| | Re: Connecting New Cylinders
|
|
"Ross Crawford" <rosscraw@bigpond.net.au> wrote in message news:Hq36E4.1q4v@lugnet.com... (...) no doubt it is i thought thin liftarm with piston vents inside axleholes could join pistons better (stronger) but wide liftarm is a very good solution (...) (21 years ago, 18-Dec-03, to lugnet.technic)
|
| |
| | Re: Connecting New Cylinders
|
|
(...) Of course if you could use the thin liftarm it would be better, but I think the wide liftarm is also an elegant solution :) ROSCO (21 years ago, 18-Dec-03, to lugnet.technic)
|
| |
| | Re: Connecting New Cylinders
|
|
sorry tobbe :) i'm sure you know what i mean you are just joking right? :)))) pixel "Tobbe Arnesson" <StPnAtM@lotek.nu> wrote in message news:Hq1sqo.13rM@lugnet.com... (...) (21 years ago, 18-Dec-03, to lugnet.technic)
|
| |
| | Re: Connecting New Cylinders
|
|
hi philo it's a pitty it could be elegant solution :) of course you checked liftarm's axlehole :) ie 1x2 liftarm pixel "Philippe Hurbain" <philohome@free.fr> wrote in message news:Hq1sxr.16Jo@lugnet.com... (...) (21 years ago, 18-Dec-03, to lugnet.technic)
|
| |
| | Re: New Williams
|
|
Matt, Very nice work! Your car looks great. The only thing I would do is add a few of the aero bits between the front wing and radiator intake if possible. Williams upgraded their website and there is some nice info on the fw25. Keep up the good (...) (21 years ago, 17-Dec-03, to lugnet.loc.au, lugnet.technic, FTX)
|
| |
| | Re: Connecting New Cylinders
|
|
Hi Pixel, (...) Yes, they fit perfectly (...) Unfortunately no, the pneumatic tube is very loose on the remaining part of the vent :( Philo (21 years ago, 17-Dec-03, to lugnet.technic)
|
| |
| | Re: Connecting New Cylinders
|
|
(...) Eeehhh... What? /Tobbe (21 years ago, 17-Dec-03, to lugnet.technic)
|
| |
| | Re: Connecting New Cylinders
|
|
i'm just curious is it possible to put piston's vents inside the axlehole? if yes then maybe the rest of vent will stick out enough to still join the tube hmm? pixel "Tobbe Arnesson" <StPnAtM@lotek.nu> wrote in message news:Hq1HJ7.rDH@lugnet.com... (...) (21 years ago, 17-Dec-03, to lugnet.technic)
|
| |
| | Re: Connecting New Cylinders
|
|
(...) I knew it would be a hassle to connect this new cylinder back-to-back! Too bad TLC did not put an axle hole in it :( I must say Mark's version looks like a winner (right until the inlet pops off :) )! -- Best regards, /Tobbe (URL) (remove SPAM (...) (21 years ago, 17-Dec-03, to lugnet.technic, FTX)
|
| |
| | Re: New Williams
|
|
XFUT: lugnet.modelteam Nice model Matthew. Here's the BS-folder with the rest of the pics: (URL) -- Best regards, /Tobbe (URL) (remove SPAM when e-mailing) (...) (21 years ago, 17-Dec-03, to lugnet.loc.au, lugnet.technic, lugnet.modelteam, FTX)
|
| |
| | Re: new design for microwalkers
|
|
(...) A whole jungle of walkers :) (21 years ago, 17-Dec-03, to lugnet.technic)
|
| |
| | Re: Modified, Motorized 8466 Off-Roader
|
|
Yikes, that's one ugly off-roader but insanely cool! Good job! Love the outdoor action shots! Cool idea with the dif. mod too! (21 years ago, 17-Dec-03, to lugnet.technic)
|
| |
| | Re: Modified, Motorized 8466 Off-Roader
|
|
(...) Here's the front differential. Only the front end has a differential, the rear is solid, I guess you could call it permanently locked. (2 URLs) PLMKWYT Nathan Falslev (21 years ago, 17-Dec-03, to lugnet.technic, FTX)
|
| |
| | Re: new design for microwalkers
|
|
The Zoo is now open!! (...) (21 years ago, 16-Dec-03, to lugnet.technic)
|
| |
| | Re: some pneumatic stuff
|
|
"Kevin L. Clague" <kevin_clague@yahoo.com> wrote in message news:Hpy4Ay.1r7s@lugnet.com... (...) i knew the name is not good :) and ofcourse i uploaded wrong picture grrrr sorry now it's correct DL (URL) should release some pressure when it's high (...) (21 years ago, 16-Dec-03, to lugnet.technic)
|
