 | | Re: Connecting New Cylinders
|
|
Hi Pixel, (...) Yes, they fit perfectly (...) Unfortunately no, the pneumatic tube is very loose on the remaining part of the vent :( Philo (21 years ago, 17-Dec-03, to lugnet.technic)
|
| |
| | Re: Connecting New Cylinders
|
|
(...) Eeehhh... What? /Tobbe (21 years ago, 17-Dec-03, to lugnet.technic)
|
| |
| | Re: Connecting New Cylinders
|
|
i'm just curious is it possible to put piston's vents inside the axlehole? if yes then maybe the rest of vent will stick out enough to still join the tube hmm? pixel "Tobbe Arnesson" <StPnAtM@lotek.nu> wrote in message news:Hq1HJ7.rDH@lugnet.com... (...) (21 years ago, 17-Dec-03, to lugnet.technic)
|
| |
| | Re: Connecting New Cylinders
|
|
(...) I knew it would be a hassle to connect this new cylinder back-to-back! Too bad TLC did not put an axle hole in it :( I must say Mark's version looks like a winner (right until the inlet pops off :) )! -- Best regards, /Tobbe (URL) (remove SPAM (...) (21 years ago, 17-Dec-03, to lugnet.technic, FTX)
|
| |
| | Re: New Williams
|
|
XFUT: lugnet.modelteam Nice model Matthew. Here's the BS-folder with the rest of the pics: (URL) -- Best regards, /Tobbe (URL) (remove SPAM when e-mailing) (...) (21 years ago, 17-Dec-03, to lugnet.loc.au, lugnet.technic, lugnet.modelteam, FTX)
|
| |
| | Re: new design for microwalkers
|
|
(...) A whole jungle of walkers :) (21 years ago, 17-Dec-03, to lugnet.technic)
|
| |
| | Re: Modified, Motorized 8466 Off-Roader
|
|
Yikes, that's one ugly off-roader but insanely cool! Good job! Love the outdoor action shots! Cool idea with the dif. mod too! (21 years ago, 17-Dec-03, to lugnet.technic)
|
| |
| | Re: Modified, Motorized 8466 Off-Roader
|
|
(...) Here's the front differential. Only the front end has a differential, the rear is solid, I guess you could call it permanently locked. (2 URLs) PLMKWYT Nathan Falslev (21 years ago, 17-Dec-03, to lugnet.technic, FTX)
|
| |
| | Re: new design for microwalkers
|
|
The Zoo is now open!! (...) (21 years ago, 16-Dec-03, to lugnet.technic)
|
| |
| | Re: some pneumatic stuff
|
|
"Kevin L. Clague" <kevin_clague@yahoo.com> wrote in message news:Hpy4Ay.1r7s@lugnet.com... (...) i knew the name is not good :) and ofcourse i uploaded wrong picture grrrr sorry now it's correct DL (URL) should release some pressure when it's high (...) (21 years ago, 16-Dec-03, to lugnet.technic)
|
| |
| | New Williams
|
|
Hi all- Delurking Welcome to my new incarnation of my williams fw25 - version 5 revision "B" (2 URLs) It's taken me all year, but I finally have a perfect model - now I get to do it all again when williams release their fw26:) PLMKWYT - I need the (...) (21 years ago, 16-Dec-03, to lugnet.loc.au, lugnet.technic, FTX)
|
| |
| | Re: Connecting New Cylinders
|
|
(...) Well, the first example is in a post by Dennis Boseman: (URL) used them in my original and/or gates. A single piston can give you two stable states, expanded or contracted. Two pistons can give you three lengths with four stable states: (...) (21 years ago, 15-Dec-03, to lugnet.technic)
|
| |
| | Modified, Motorized 8466 Off-Roader
|
|
I've been working on this for a little while. I've strengthened the suspension and drivetrain on the front of the 8466, and created an entirely new rear suspension that articulates over just about everything. The vehicle is 4 wheel drive, (...) (21 years ago, 15-Dec-03, to lugnet.technic, FTX)
|
| |
| | Re: some pneumatic stuff
|
|
(...) What is a protection valve? (...) A piston with both ports used, and a switch with all three ports used is a transistor, right? (...) Kevin (21 years ago, 15-Dec-03, to lugnet.technic)
|
| |
| | some pneumatic stuff
|
|
hi thinking about pneumatics i found an idea of protection valve DL (URL) pneumatic transistor :))))) DL (URL) (21 years ago, 15-Dec-03, to lugnet.technic)
|
| |
| | Re: The badgers have driven me insane...
|
|
(...) This badgerthing is seriously thretening my health. Each time some new version of the theme shows up I laugh so hard I allmost suffocate! My personal health aside, good work dude! Can't wait to se the Snake in Lego... /Henrik ps. (URL) (21 years ago, 15-Dec-03, to lugnet.build.sculpture, lugnet.technic, lugnet.fun)
|
| |
| | Re: JCB JS220 Excavator
|
|
Hello Could you please let us know when you have posted the CAD files. I would love to build one. Thanks (21 years ago, 15-Dec-03, to lugnet.technic, FTX)
|
| |
| | Re: Connecting New Cylinders
|
|
(...) Probably what amounts to a braindead question coming up... Could someone describes some possible applications for this design pattern? Thanks >> Mark (21 years ago, 14-Dec-03, to lugnet.technic)
|
| |
| | Re: Connecting New Cylinders
|
|
Hi Jonathan, For the loading crane of my MAN tipper truck I've connected to old style cylinders with 1/2 pins and plate corners. In the crane arm there's only space for a two studs wide cylinder so I've glued to together :) (URL) Dennis Bosman (URL) (...) (21 years ago, 14-Dec-03, to lugnet.technic, FTX)
|
| |
| | Re: Connecting New Cylinders
|
|
(...) Rather thank Mark... I just made the photograph :o) Philo (21 years ago, 13-Dec-03, to lugnet.technic, FTX)
|
