 | | Re: Connecting New Cylinders
|
|
(...) Thanks Philo for the ideas, I find them very useful. (21 years ago, 13-Dec-03, to lugnet.technic, FTX)
|
| |
| | Re: Connecting New Cylinders
|
|
Thanks Kevin for the ideas. (21 years ago, 13-Dec-03, to lugnet.technic)
|
| |
| | Re: Connecting New Cylinders
|
|
(...) It works very well! (URL) Philo (21 years ago, 12-Dec-03, to lugnet.technic, FTX)
|
| |
| | Re: JCB JS220 Excavator
|
|
(...) I keep most of them built up these days, you are right, it is definitely hard to take these apart, they take months to build... Really the only time I think about taking a model apart is when it is superceded by a better one. Jennifer (21 years ago, 12-Dec-03, to lugnet.technic)
|
| |
| | Re: Connecting New Cylinders
|
|
(...) Well, I don't have any of the new pistons so this may not work, but have a look at this setup (click for larger view): (URL) With the new pistons, you should be able to use the new 1x2 liftarms instead. To get the liftarm to seat properly over (...) (21 years ago, 12-Dec-03, to lugnet.technic, FTX)
|
| |
| | My first swiled LEGO
|
|
I called LEGO the other day about a piston that had a broken off pressure port, and got a replacement. The replacement piston has swirls of a darker colored plastic in the yellow cylinder part as can be seen here in the right piston. (URL) not aware (...) (21 years ago, 12-Dec-03, to lugnet.technic)
|
| |
| | Re: Connecting New Cylinders
|
|
(...) Hi Jonathan, Here is a second version. The gaps between two back to back are not nice integral stud lengths. This makes it a pain. It turns out that the larger of the two gaps is the pretty close to the distance between the outer edges of (...) (21 years ago, 12-Dec-03, to lugnet.technic)
|
| |
| | Re: Connecting New Cylinders
|
|
(...) Hi Jonathan, I'd never tried this, but was able to come up with this: (URL) problem with it is that the pistons are not in perfect alignment. (URL) (21 years ago, 12-Dec-03, to lugnet.technic)
|
| |
| | Re: JCB JS220 Excavator
|
|
(...) A comment on how you might be able to control the speed of pneumatics is to add an orifice to both of the line of the cylinder. This would regulate the amount and speed of the air entering and leaving the cylinder. Hope this gives you some (...) (21 years ago, 12-Dec-03, to lugnet.technic)
|
| |
| | Connecting New Cylinders
|
|
Hello I am trying to connect two of the new form factor cylinders back-to-back. Does any one have any ideas? I wish only to use lego parts. Thanks (21 years ago, 12-Dec-03, to lugnet.technic)
|
| |
| | Re: Pneumatic hoses
|
|
(...) sells fish tanks & supplies. We used it to make a couple of long (1.5m) tubing lengths, it worked very well and was basically a perfect fit on the Lego peumatic pieces. JohnG, GMLTC (21 years ago, 11-Dec-03, to lugnet.technic)
|
| |
| | Re: Pneumatic hoses
|
|
(...) There's always fuel hose for model airplanes, but that's expensive (high grade silicone to be fuel and heat resistant). Another source is your well sorted car part dealer, they have thin vacuum hoses that might fit. A friend used this and it's (...) (21 years ago, 11-Dec-03, to lugnet.technic)
|
| |
| | Re: 2004 Products see?
|
|
(...) What you got there is a regular sized antenna, put through a 1x1 cone, and then through the hole on a 1x1 clip/holder/thingy. You can see the butt of the antenna on the other side. Most defenitly a regular sized antenna. It would be nice to (...) (21 years ago, 10-Dec-03, to lugnet.pirates, lugnet.castle, lugnet.technic.bionicle, lugnet.technic, FTX)
|
| |
| | Re: 2004 Products see?
|
|
It looks like the trans-orange antennae on the side of the 8380 race set (1st race set listed): (...) is a new, shorter size antenna. Anyone else think so? David "Fuzzy" Gregory (21 years ago, 10-Dec-03, to lugnet.pirates, lugnet.castle, lugnet.technic.bionicle, lugnet.technic, FTX)
|
| |
| | Re: Pneumatic hoses
|
|
Hi Morten, for the interconnection of a pneumatic remote control with the model I use the isolation tube of the cables used for the electric installation of a house. It has a cross section of 1.5 mm^2. The isolation fits perfectly and air tight in (...) (21 years ago, 9-Dec-03, to lugnet.technic)
|
| |
| | Re: 2004 Products see?
|
|
"Aaron Muhl" <Aaron_Muhl@yahoo.com> wrote in message news:HpM8DI.22vI@lugnet.com... (...) thankyouthankyouthan...outhankyou I've been trying to see Xpod pics for a very long time. Now I'm trying to figure out what the lid is. At first glance it (...) (21 years ago, 9-Dec-03, to lugnet.pirates, lugnet.castle, lugnet.technic.bionicle, lugnet.technic, lugnet.space)
|
| |
| | Re: 2004 Products see?
|
|
Thanks for the leaks! Unfortunately, no good castle sets there.... The pirate sets looked interesting until I looked closer at the figures. BTW, congrats to .space! There is a "pod" set! -Aaron "matt doyle" <parisinflames08@yahoo.com> wrote in (...) (21 years ago, 9-Dec-03, to lugnet.pirates, lugnet.castle, lugnet.technic.bionicle, lugnet.technic, lugnet.space)
|
| |
| | Re: 2004 Products see?
|
|
Leak.... Save 'em while they're still there im sure they will be gone shortly (18 URLs) (21 years ago, 9-Dec-03, to lugnet.announce, lugnet.pirates, lugnet.castle, lugnet.technic.bionicle, lugnet.technic, FTX)
|
| |
| | Re: Pneumatic hoses
|
|
(...) I bought mine from Revol in France ((URL) "Tuyau"), but their website is only in french though they seem to be able to sell internationnally. Philo (21 years ago, 8-Dec-03, to lugnet.technic)
|
| |
| | Burger King Bionicles
|
|
Saw the new Burger King Bionicle offers today (didn't buy as I was too hungry images of the figurines (not really lego at all(and I don't mean that ikn a Biuonicle sense!)) can be seen at (URL) meal comes in a box propertioned like a lego set box (...) (21 years ago, 7-Dec-03, to lugnet.loc.uk, lugnet.technic.bionicle, lugnet.market.shopping)
|
