 | | Srial problem
|
|
Hi. I am putting together a Handyboard and have been having success until it came time to test the bootstrap mode. The interface board's voltages check out and it blinks as it attempts to download. I am using an E1 and the Mac 6811 downloader. The E (...) (22 years ago, 9-Feb-02, to lugnet.robotics.handyboard)
|
| |
| | Re: Sensor Connector
|
|
The LEGO shaft encoder and light sensor are active sensors that need a special circuit. The Expansion Board for the HB provides this ckt and the requisite drivers. Your simplest path to using these with the HB is to get an Exp Bd. Barring that, you (...) (22 years ago, 7-Feb-02, to lugnet.robotics.handyboard)
|
| |
| | Re: Sensor Connector
|
|
(...) Thanks, I thought there might be a special connector but I see now that its a standard enough connector. Another question: How can I get the handy board to read from the lego rotation sensor and the lego light sensor? I can get the touch (...) (22 years ago, 7-Feb-02, to lugnet.robotics.handyboard)
|
| |
| | Re: Sensor Connector
|
|
Info on doing this is at (URL) . The male strip header is 929400-01-36-ND from Digikey. Fred (...) (22 years ago, 6-Feb-02, to lugnet.robotics.handyboard)
|
| |
| | Re: Sensor Connector
|
|
(...) Oh, that's easy. Just check out your local electronics store. I don't know if there is a Fry's Electronics in your area, but they have them. Radio Shack? I don't know, but I would assume anyone who sells electronic components would have them. (...) (22 years ago, 6-Feb-02, to lugnet.robotics.handyboard)
|
| |
| | Re: Sensor Connector
|
|
(...) Actually what I was looking for was how to make the male header pins to connect to the HB. Is there anywhere to buy them or how did you make them. Thanks for your answer, brendan (22 years ago, 6-Feb-02, to lugnet.robotics.handyboard)
|
| |
| | Re: Sensor Connector
|
|
(...) Actually, you can make a half way decent replica of the Lego two plate high connector at this point quite easily. When you prepare the 2x2 piece of the electric plate, cut the center circular section away from the underneath. Then, solder the (...) (22 years ago, 6-Feb-02, to lugnet.robotics.handyboard)
|
| |
| | Re: Sensor Connector
|
|
I've bought some lego electric plates (part 5037) from lego.com, and they seem to be withstanding the heat of a soldering iorn quite well (that was my fear... that I would turn them into bubbling messes). Actually they're holding up better than the (...) (22 years ago, 6-Feb-02, to lugnet.robotics.handyboard)
|
| |
| | Sensor Connector
|
|
I currently have lego motors and wires that I have used with the RCX but now Im using the Handy Board. The book explains how to connect the motor to the handy board by connecting a wire to a sensor connector but it doesnt state where to get such a (...) (22 years ago, 6-Feb-02, to lugnet.robotics.handyboard)
|
| |
| | Premature announcement of Interactive C 4.0
|
|
Actually, Fred's announcement is a little premature, sorry. Several important things to know if you do choose to download the current version of IC: 1) The libraries are tuned for the Botball contest (www.botball.org) and by default include a (...) (22 years ago, 29-Jan-02, to lugnet.robotics.handyboard)
|
